Metal stamping and fabricating shops

Stamping and fabricating shops feed coil or sheet into power presses and roll formers to make vehicle parts, hardware, closures and small metal goods, often adding welding, finishing and assembly. The metal is benign; the presses are not, and customers expect defect-free parts delivered to the hour.

Manufacturing · NAICS 332119 · SIC 3469 · Updated November 2026

01 / Loss drivers

Where losses come from.

  1. 01

    Hand and finger amputations at press points of operation and during die setting

  2. 02

    Defective batches that force customers to sort, rework or recall assemblies

  3. 03

    Fires in hydraulic systems, lubricant mist, welding cells and finishing lines

How it comparesEach line’s rating against the average for its NAICS sector, Manufacturing (178 business types), and for all 747.
  1. PropertyProperty: Elevated, 3 of 5; sector average 3.7; all business types 2.9.
  2. Business interruptionBusiness interruption: Elevated, 3 of 5; sector average 3.5; all business types 2.7.
  3. Premises liabilityPremises liability: Low, 1 of 5; sector average 1.9; all business types 2.7.
  4. Products and completed workProducts and completed work: Elevated, 3 of 5; sector average 3.4; all business types 2.6.
  5. Workers’ injuryWorkers’ injury: High, 4 of 5; sector average 3.4; all business types 3.0.
  6. Commercial autoCommercial auto: Moderate, 2 of 5; sector average 2.3; all business types 2.5.
  7. Crime and theftCrime and theft: Moderate, 2 of 5; sector average 1.9; all business types 2.2.
  8. Inland marine and equipmentInland marine and equipment: Elevated, 3 of 5; sector average 2.6; all business types 2.6.
  9. EnvironmentalEnvironmental: Elevated, 3 of 5; sector average 2.8; all business types 2.3.
  10. Cyber and dataCyber and data: Elevated, 3 of 5; sector average 2.7; all business types 2.7.
  11. Professional liabilityProfessional liability: Moderate, 2 of 5; sector average 1.5; all business types 2.0.
  12. Umbrella and excessUmbrella and excess: High, 4 of 5; sector average 3.6; all business types 3.6.
What’s changing
  • Servo presses, robots and in-die sensors cut hand feeding and amputations, but add networked controls and costly equipment with long replacement times.
  • Electric vehicle programs bring new parts such as battery trays and busbars in aluminum and copper, raising stock values and theft exposure.
  • Vehicle makers are shifting more recall and warranty costs onto suppliers, and some replace multi-part stamped assemblies with single large castings.
02 / Line by line

Twelve lines, rated.

Each line shows its rating and the reason for it; open a line for what to watch for and the controls that matter. Ratings are UrbanStat’s own editorial view of a typical business of this type, on a five-step scale. They are a starting point for questions, not a quote, a rate or a statistical measure.

Property

Elevated
Presses and steel stock are robust, but hydraulic oil, drawing lubricants, weld spatter and paint or powder lines supply ignition and fuel.

Fire, explosion, water and weather damage to buildings, contents and stock.

Watch for
  • Oil-soaked floors, pits and scrap conveyors under presses
  • Paint or powder coating added to the shop
  • Plastic totes and cardboard packaging stacked high among presses
Controls that matter
  • Sprinklers throughout, including press pits and finishing booths
  • Routine cleaning of pits and oil mist ducting
  • Hot work permits and welding cells screened from packaging

Business interruption

Elevated
Presses can be repaired or work moved, but dies are unique and automotive schedules allow no slack.

How long and how costly a shutdown is.

Watch for
  • One large transfer press carrying a major contract
  • Customer-owned dies with no backup tooling
  • Supply contracts with shutdown penalties
Controls that matter
  • Die storage protected and separated from production
  • Contingency agreements with other stampers for critical parts
  • Preventive maintenance on clutches, brakes and feed lines

Premises liability

Low
A closed factory with only carriers and customers' auditors on site.

Injuries to customers and the public, on site or caused by operations elsewhere.

Watch for
  • Visiting drivers in coil unloading areas
Controls that matter
  • Controlled loading zones and visitor escorts

Products and completed work

Elevated
Most output is components; a cracked bracket or mis-formed seat or brake part multiplies through thousands of finished goods.

Harm caused by what the business sells, serves, makes, installs or repairs.

Watch for
  • Parts for vehicle restraint, seating, steering or braking systems
  • Own-brand consumer goods with sharp edges or moving parts
  • Contracts making the stamper pay sorting and recall costs
Controls that matter
  • In-die sensors and statistical checks on critical dimensions
  • Lot traceability from coil certificate to shipped container
  • Negotiated limits on consequential and recall costs

Workers’ injury

High
Power presses are the classic amputation hazard, added to lacerations from sheet edges, noise and coil handling.

Injuries and illness to employees.

Watch for
  • Hand feeding or part removal within the die space
  • Light curtains muted or guards bypassed for short runs
  • Temporary workers put on presses with little training
Controls that matter
  • Light curtains, two-hand controls and brake monitors tested each shift
  • Die blocks and lockout for every setup and jam
  • Automated feeds and part ejection

Commercial auto

Moderate
Parts go out by carrier; a few shops run a truck for local customers and outside finishers.

Owned, hired and employee-driven vehicles, deliveries, customers’ vehicles in care.

Watch for
  • Daily shuttle runs to platers, painters or assembly plants
Controls that matter
  • Driver record checks and secured bins and racks

Crime and theft

Moderate
Copper, brass, stainless and aluminum coil and scrap have ready buyers.

Burglary, robbery, employee dishonesty, cash, payment and invoice fraud.

Watch for
  • Scrap bins emptied by a dealer with no weight reconciliation
  • Nonferrous coil stored by the dock door
Controls that matter
  • Scrap weights tracked against coil usage
  • Alarm and cameras on stock and scrap areas

Inland marine and equipment

Elevated
Customers' dies and fixtures sit in the shop for the life of a program, and parts travel out for finishing.

Property in transit, at job sites or in the insured’s care, and mobile equipment.

Watch for
  • No list or values for customer-owned tooling
  • Work in progress held at outside platers or heat treaters
Controls that matter
  • Tooling register with replacement values and ownership
  • Cover for goods at and in transit to processors

Environmental

Elevated
Lubricants, washer solutions, degreasing solvents and finishing chemicals are used daily, and older sites have solvent legacies.

Pollution on or from the site or the work.

Watch for
  • Past or present vapor degreasing with chlorinated solvents
  • Floor drains and sumps beneath oily presses
  • In-house plating or phosphating
Controls that matter
  • Aqueous cleaning in place of solvent degreasing
  • Sealed pits, oil-water separation and licensed waste hauling

Cyber and data

Elevated
Press lines, scheduling and electronic orders from vehicle customers are networked; ransomware stops shipments that customers expect within hours.

Data breaches, ransomware, system outages and attacks on connected equipment.

Watch for
  • Customer ordering and shipping portals on unprotected office systems
  • Press controls and robots with remote vendor access
Controls that matter
  • Segmented production network and controlled vendor connections
  • Tested recovery of order and shipping systems from offline backups

Professional liability

Moderate
Shops often design dies and suggest changes to customers' parts, so an engineering error can be argued as advice as well as a defect.

Loss or injury caused by advice, design, testing, care or another professional service.

Watch for
  • Part design or engineering changes proposed by the shop
  • Die design sold as a separate service
Controls that matter
  • Customer sign-off on part drawings and engineering changes
  • Documented design reviews before tooling is built

Umbrella and excess

High
Stamped parts in seats, restraints and brakes reach thousands of vehicles, so one defect can bring injury suits across a whole model.

How likely one liability event is to exhaust primary limits.

Watch for
  • Safety-critical vehicle parts or own-brand consumer products
  • Contracts that pass vehicle recall costs to the stamper
Controls that matter
  • Error-proofing and full traceability on safety-critical parts
  • Contract caps on recall and consequential costs
03 / Property picture

Construction, occupancy, protection, exposure.

What a risk engineer expects to find at a typical site of this type, and what to compare a submission against.

Construction
Steel-frame, metal-clad buildings with wide roof spans, deep press pits and scrap tunnels below the floor, crane bays for coil and dies, and later additions.
Occupancy
Heavy presses with hydraulic oil and drawing lubricants, oil mist, welding cells, washers, paint or powder lines, and stacked plastic totes and cardboard packaging.
Protection
Sprinklers throughout including press pits and finishing booths, cleaned pits and mist ducts, hot work permits, protected die storage, and monitored alarms.
Exposure
Industrial parks shared with other suppliers to the same customers; neighbors' storage and finishing shops add fire exposure, and lightweight roofs face wind and hail.
04 / Checklist

What to ask and look for.

Start with the desk review before quoting, then walk the site. Tick questions off as you go; ticks are kept in this browser only.

Before quoting: ask the broker or owner

Documents to request

On site: work and processes

On site: presses and safeguarding

On site: building and fire protection

On site: environment and records

Refer or decline if you find

  • Presses running with light curtains bypassed or guards removed
  • Hand-fed presses operated by untrained temporary staff
  • No register of customer-owned dies
  • Chlorinated solvent degreaser with no site investigation
  • Contracts with unlimited recall liability
05 / Location

How UrbanStat data helps.

Press pits and scrap tunnels flood readily, and coil steel rusts within days of getting wet. Light metal-clad buildings with wide spans are vulnerable to tornado, wind and hail.

TornadoFloodWindHailEarthquake
  • Flood scores at the address show whether press pits, scrap tunnels and floor-stored coil are exposed, on sites where shallow water alone stops production.
  • Tornado, wind and hail scores at the address inform roof terms for lightweight metal-clad plants before the quote is released.
  • Street-by-street exposure views reveal accumulations where stampers and their vehicle-industry customers share one industrial park, with alerts when totals pass a threshold.
Tornado · Flood · Wind · Hail
06 / Public loss data

What the published numbers say.

Official statistics for the industry or property type closest to this business. They describe the industry as a whole, not any one insured.

Workers’ injury frequency

4.2 recordable injuries and illnesses per 100 full-time workers, above the private-industry average of 2.3.

Metal crown, closure, and other metal stamping (except automotive)
4.2
All private industry
2.3

1.2 of these cases per 100 workers involved days away from work.

United States, 2024. Industry: Metal crown, closure, and other metal stamping (except automotive) (NAICS 332119). Source: U.S. Bureau of Labor Statistics, Survey of Occupational Injuries and Illnesses, Table 1: incidence rates of nonfatal occupational injuries and illnesses by industry and case types, 2024.

Workplace deaths

5 fatal work injuries in 2024, most often from falls, slips and trips (3).

Manufacturing
2.4
All workers
3.3

Deaths per 100,000 full-time equivalent workers, for the industry sector as a whole.

United States, private industry, 2024. Industry: Forging and Stamping (NAICS 33211), the closest published group. Source: U.S. Bureau of Labor Statistics, Census of Fatal Occupational Injuries; sector rates.

Most cited safety standards

135 citations from 43 inspections; 61% were classed serious, willful or repeat.

  • 1910.147 The control of hazardous energy (lockout/tagout)
    35
  • 1910.212 General requirements for all machines
    16
  • 1910.219 Mechanical power-transmission apparatus
    7
  • 1910.217 Mechanical power presses
    7
  • 1910.178 Powered industrial trucks
    5

Standards cited most often in this industry, by number of citations.

United States, citations issued October 2024 to September 2025 (federal fiscal year 2025). Industry: Metal Crown, Closure, and Other Metal Stamping (except Automotive) (NAICS 332119). Covers federal and state-plan inspections. A citation is one violation item; one inspection can produce several. Source: U.S. Department of Labor, Occupational Safety and Health Administration, OSHA enforcement data (inspections and violations); standard titles from the Code of Federal Regulations, Title 29 (section headings).

Fire frequency

7,966 fires a year reported in industrial and manufacturing properties, causing about $810 million in direct property damage a year.

United States, 2020 to 2024, annual average. The group includes utility, defense, agriculture and mining properties. Source: National Fire Protection Association, Structure Fires in Industrial and Manufacturing Properties.

Toxic chemical releases

83 facilities reported toxic chemical releases totaling 237,869 pounds on and off site.

  • Sodium nitrite
    83,601
  • Certain glycol ethers
    58,554
  • 1-bromopropane
    15,913

Chemicals released in the largest amounts, in pounds. 58 of the facilities reported at least one chemical classed as a carcinogen.

United States, 2024. Industry: Metal Crown, Closure, and Other Metal Stamping (except Automotive) (NAICS 332119). Covers facilities in listed industries with ten or more full-time employees that handle listed chemicals above set thresholds. Source: U.S. Environmental Protection Agency, Toxics Release Inventory basic data files.

Industry loss ratios by line2020 to 2024, the same table on every guide

Loss ratios are published by line of insurance, not by business type. They show how each line has run for insurers as a whole, whatever the business insured.

Published lineClosest line in this guide20202021202220232024
FireProperty63.2%67.3%62.4%45.5%40.9%
Commercial multiple perilProperty and liability sold as a package61.2%60.2%59.4%61.2%54.4%
Inland marineInland marine and equipment64.5%49.4%47.1%44.1%44.0%
Other liabilityPremises liability, and most umbrella, professional (other than medical) and cyber cover65.1%58.8%61.0%63.7%71.2%
Products liabilityProducts and completed work48.2%52.2%46.0%57.5%60.3%
Workers’ compensationWorkers’ injury47.9%49.2%45.0%44.3%46.0%
Commercial auto liabilityCommercial auto68.3%66.5%71.9%76.8%77.6%
Commercial auto physical damageCommercial auto50.9%56.3%64.3%65.1%57.9%

United States. Losses incurred as a percent of direct premiums earned, countrywide, before reinsurance and not including loss adjustment expense. Source: National Association of Insurance Commissioners, Report on Profitability by Line by State in 2024, ten-year summary.

Coverages to raise
Equipment breakdown
Large presses, clutches, servo drives and transfer systems fail mechanically, with long lead times for replacements.
Product recall
Vehicle and appliance customers pass sorting, recall and line-down costs back to their stampers.
Customers' tooling in care
Customers' dies and fixtures can be worth more than the shop's own presses and are often unscheduled.
Site pollution liability
Chlorinated degreasers and oily press pits from past decades leave groundwater contamination that follows the site.
Classification
SystemCodeIndustry
NAICS 2022, primary332119Metal Crown, Closure, and Other Metal Stamping (except Automotive)
NAICS 2022336370Motor Vehicle Metal Stamping
NAICS 2022332114Custom Roll Forming
NAICS 2022332510Hardware Manufacturing
NAICS 2022332999All Other Miscellaneous Fabricated Metal Product Manufacturing
NAICS 2022339993Fastener, Button, Needle, and Pin Manufacturing
SIC 1987, primary3469Metal Stampings, NEC
SIC 19873465Automotive Stampings
SIC 19873499Fabricated Metal Products, NEC
SIC 19873429Hardware, NEC
Next step

See this risk on the map.

Book a 30-minute walkthrough tailored to your portfolio and perils of interest.

Request a Demo →