Sheet metal shops and contractors
Sheet metal firms cut, bend and join thin steel, aluminum and copper into ductwork, flashings, gutters, enclosures and custom parts, and most install what they make. The shop adds laser and press brake hazards; the field work adds roofs, ladders and torches on other people's buildings.
Where losses come from.
- 01
Falls from roofs, ladders and lifts, and deep cuts from sheet edges
- 02
Fires started by soldering, welding or cutting on customers' buildings
- 03
Leaks, condensation and exhaust duct faults that appear after the job is finished
- PropertyProperty: Moderate, 2 of 5; sector average 3.7; all business types 2.9.
- Business interruptionBusiness interruption: Moderate, 2 of 5; sector average 3.5; all business types 2.7.
- Premises liabilityPremises liability: Elevated, 3 of 5; sector average 1.9; all business types 2.7.
- Products and completed workProducts and completed work: Elevated, 3 of 5; sector average 3.4; all business types 2.6.
- Workers’ injuryWorkers’ injury: High, 4 of 5; sector average 3.4; all business types 3.0.
- Commercial autoCommercial auto: Elevated, 3 of 5; sector average 2.3; all business types 2.5.
- Crime and theftCrime and theft: Moderate, 2 of 5; sector average 1.9; all business types 2.2.
- Inland marine and equipmentInland marine and equipment: Elevated, 3 of 5; sector average 2.6; all business types 2.6.
- EnvironmentalEnvironmental: Moderate, 2 of 5; sector average 2.8; all business types 2.3.
- Cyber and dataCyber and data: Moderate, 2 of 5; sector average 2.7; all business types 2.7.
- Professional liabilityProfessional liability: Moderate, 2 of 5; sector average 1.5; all business types 2.0.
- Umbrella and excessUmbrella and excess: High, 4 of 5; sector average 3.6; all business types 3.6.
- Automated coil lines and fiber lasers move more duct fabrication into the shop, cutting field hours but concentrating value in a few machines.
- Heat pump and energy retrofit work brings crews into occupied older buildings, where concealed asbestos and hot work in voids are common.
- Metal roofing and cladding demand grows after hail and wind events, putting crews on storm-damaged roofs in unsafe conditions.
Twelve lines, rated.
Each line shows its rating and the reason for it; open a line for what to watch for and the controls that matter. Ratings are UrbanStat’s own editorial view of a typical business of this type, on a five-step scale. They are a starting point for questions, not a quote, a rate or a statistical measure.
Property
ModerateMetal stock and machines are hard to burn; exposure comes from welding, laser cutting, small paint areas and duct insulation.
Fire, explosion, water and weather damage to buildings, contents and stock.
- Laser or plasma cutting tables with poor fume extraction
- Duct liner, insulation and adhesives stored in bulk
- Spray painting without a booth
- Fume extraction with spark arrestors on laser and plasma tables
- Duct liner and adhesives stored away from welding and cutting bays
- Painting confined to a ventilated booth with flammables in a rated cabinet
Business interruption
ModerateWork can be subcontracted or shifted to hand methods while a laser, shear or brake is repaired.
How long and how costly a shutdown is.
- One coil line or laser handling all duct production
- Service contract on key machines and a peer shop for overflow
Premises liability
ElevatedCrews bring torches, long sharp materials and open roof penetrations onto occupied buildings.
Injuries to customers and the public, on site or caused by operations elsewhere.
- Torch soldering of copper or flashing on timber roofs
- Roof openings left unsealed overnight
- Material hoisted over entrances and walkways
- Hot work permit and fire watch after any open-flame work
- Temporary weatherproofing at every opening before leaving
- Exclusion zones below hoisting and roof-edge work
Products and completed work
ElevatedCompleted work fails slowly: leaking flashings, sweating ducts, dislodged panels and kitchen exhaust ducts that are not liquid-tight.
Harm caused by what the business sells, serves, makes, installs or repairs.
- Grease duct, fume exhaust, and fire or smoke dampers in rated walls
- Metal roofing and wall cladding on large buildings
- Custom guards, enclosures or equipment sold to manufacturers
- Welded, tested seams and access doors on grease duct
- Fastening and expansion details to the panel maker's specification
- Photos and sign-off at completion of each roof detail
Workers’ injury
HighInstallers work at height carrying awkward, razor-edged pieces, and shop staff use shears, brakes and rolls.
Injuries and illness to employees.
- Roof and gutter work from ladders without fall protection
- Press brakes operated without light curtains or guarding
- Work in ceilings and mechanical rooms containing old insulation
- Guardrails, anchors or lifts planned for every elevated task
- Cut-resistant gloves and sleeves as standard issue
- Safeguarded brakes and shears with trained operators
Commercial auto
ElevatedVans and stake trucks leave daily carrying duct sections, long gutter stock and ladders.
Owned, hired and employee-driven vehicles, deliveries, customers’ vehicles in care.
- Over-length loads on roof racks or open trailers
- Employees taking company vehicles home
- Load securing rules with flagged overhangs
- Driving record checks, telematics and a personal-use policy
Crime and theft
ModerateCopper sheet, coil and scrap, plus hand tools on vans, are the usual targets.
Burglary, robbery, employee dishonesty, cash, payment and invoice fraud.
- Copper and tools left in vehicles or on site overnight
- Scrap sold for cash by shop staff
- Locked van storage and stock returned to the shop nightly
- Scrap sales paid by traceable means to the company
Inland marine and equipment
ElevatedTools, lifts and fabricated sections sit on job sites and in vehicles until installed and accepted.
Property in transit, at job sites or in the insured’s care, and mobile equipment.
- Prefabricated duct or panels stored on open sites
- Rented lifts and hoists in the insured's care
- Installation floater sized to the largest job
- Just-in-time delivery of fabricated sections to site
Environmental
ModerateOld duct insulation, sealants and roof materials may contain asbestos, and leaks from finished work feed mold.
Pollution on or from the site or the work.
- Demolition of old ductwork or flashing in older buildings
- Mold claims following duct condensation or roof leaks
- Asbestos survey before removal work begins
- Insulation and vapor barrier details checked at handover
Cyber and data
ModerateRansomware on CAD, nesting and estimating systems stops the laser and coil line, though customer data is mostly business contacts.
Data breaches, ransomware, system outages and attacks on connected equipment.
- Laser and coil line controllers on the office network with vendor remote access
- Emailed payment changes from suppliers and general contractors
- Offline backups of nesting programs and drawings, tested by restoring
- Call-back check on any change to bank or payment details
Professional liability
ModerateShop drawings, duct layouts and design-assist work for contractors put the firm's own sizing and detailing decisions on the line.
Loss or injury caused by advice, design, testing, care or another professional service.
- Design-build duct systems or kitchen exhaust sized by the firm's own staff
- Engineer of record sign-off on any system the firm designs
Umbrella and excess
HighA torch fire on an occupied building, a grease duct fire years later or material dropped from a roof can exceed primary limits.
How likely one liability event is to exhaust primary limits.
- Hot work on occupied commercial roofs or historic buildings
- Grease duct installed in multi-story mixed-use buildings
- Hot work permits with a fire watch after torches are put away
- Limits matched to the largest building and contract worked on
Construction, occupancy, protection, exposure.
What a risk engineer expects to find at a typical site of this type, and what to compare a submission against.
- Construction
- A single-story steel or masonry shop with a yard for coil, duct sections and vans; crews work on customers' roofs, ceilings and mechanical rooms of every age.
- Occupancy
- Shearing, laser and plasma cutting, press braking, welding and soldering in the shop, with duct liner, sealants and small paint stocks; torch work and hoisting on job sites.
- Protection
- Fume extraction with spark arrestors on cutting tables, liner and adhesives kept away from hot work, extinguishers on every van, and hot work permits with fire watch on site.
- Exposure
- Shops sit in industrial parks beside other trades; on site, a torch on a timber roof or in a ceiling void threatens the customer's whole building and its occupants.
What to ask and look for.
Start with the desk review before quoting, then walk the site. Tick questions off as you go; ticks are kept in this browser only.
Before quoting: ask the broker or owner
Documents to request
On site: work performed
On site: job sites
On site: shop and equipment
On site: records
Refer or decline if you find
- Open-flame work on roofs with no permit or fire watch
- Roof and gutter work without fall protection
- Grease duct assembled with unsealed or non-welded seams
- Uninsured subcontract installers
- Fire and smoke dampers installed with no inspection or test records
How UrbanStat data helps.
Storm seasons drive both demand and claims: half-finished roofs and flashings are exposed to wind and rain, installed metal panels to hail. Copper stock and loaded vans make local theft rates relevant.
- Crime scores at the address inform theft terms for copper stock, tools and loaded vans kept at the shop overnight.
- Hail and wind scores at the address show how exposed the shop roof, yard-stored coil and duct sections, and parked vans are to storm damage.
- The risk analysis API returns peril scores in seconds, so a small shop-and-yard location can be screened inside the quoting workflow.
What the published numbers say.
Official statistics for the industry or property type closest to this business. They describe the industry as a whole, not any one insured.
3.3 recordable injuries and illnesses per 100 full-time workers, above the private-industry average of 2.3.
1.2 of these cases per 100 workers involved days away from work.
United States, 2024. Industry: Sheet metal work manufacturing (NAICS 332322). Source: U.S. Bureau of Labor Statistics, Survey of Occupational Injuries and Illnesses, Table 1: incidence rates of nonfatal occupational injuries and illnesses by industry and case types, 2024.
5 fatal work injuries in 2024.
Deaths per 100,000 full-time equivalent workers, for the industry sector as a whole.
United States, private industry, 2024. Industry: Sheet Metal Work Manufacturing (NAICS 332322). Source: U.S. Bureau of Labor Statistics, Census of Fatal Occupational Injuries; sector rates.
679 citations from 193 inspections; 65% were classed serious, willful or repeat.
- 1910.212 General requirements for all machines61
- 1910.147 The control of hazardous energy (lockout/tagout)59
- 1910.1200 Hazard communication55
- 1910.134 Respiratory protection43
- 1910.217 Mechanical power presses24
Standards cited most often in this industry, by number of citations.
United States, citations issued October 2024 to September 2025 (federal fiscal year 2025). Industry: Sheet Metal Work Manufacturing (NAICS 332322). Covers federal and state-plan inspections. A citation is one violation item; one inspection can produce several. Source: U.S. Department of Labor, Occupational Safety and Health Administration, OSHA enforcement data (inspections and violations); standard titles from the Code of Federal Regulations, Title 29 (section headings).
7,966 fires a year reported in industrial and manufacturing properties, causing about $810 million in direct property damage a year.
United States, 2020 to 2024, annual average. The group includes utility, defense, agriculture and mining properties. Source: National Fire Protection Association, Structure Fires in Industrial and Manufacturing Properties.
99 facilities reported toxic chemical releases totaling 359,813 pounds on and off site.
- Certain glycol ethers143,411
- Toluene66,028
- Chlorodifluoromethane47,066
Chemicals released in the largest amounts, in pounds. 58 of the facilities reported at least one chemical classed as a carcinogen.
United States, 2024. Industry: Sheet Metal Work Manufacturing (NAICS 332322). Covers facilities in listed industries with ten or more full-time employees that handle listed chemicals above set thresholds. Source: U.S. Environmental Protection Agency, Toxics Release Inventory basic data files.
Industry loss ratios by line2020 to 2024, the same table on every guide
Loss ratios are published by line of insurance, not by business type. They show how each line has run for insurers as a whole, whatever the business insured.
| Published line | Closest line in this guide | 2020 | 2021 | 2022 | 2023 | 2024 |
|---|---|---|---|---|---|---|
| Fire | Property | 63.2% | 67.3% | 62.4% | 45.5% | 40.9% |
| Commercial multiple peril | Property and liability sold as a package | 61.2% | 60.2% | 59.4% | 61.2% | 54.4% |
| Inland marine | Inland marine and equipment | 64.5% | 49.4% | 47.1% | 44.1% | 44.0% |
| Other liability | Premises liability, and most umbrella, professional (other than medical) and cyber cover | 65.1% | 58.8% | 61.0% | 63.7% | 71.2% |
| Products liability | Products and completed work | 48.2% | 52.2% | 46.0% | 57.5% | 60.3% |
| Workers’ compensation | Workers’ injury | 47.9% | 49.2% | 45.0% | 44.3% | 46.0% |
| Commercial auto liability | Commercial auto | 68.3% | 66.5% | 71.9% | 76.8% | 77.6% |
| Commercial auto physical damage | Commercial auto | 50.9% | 56.3% | 64.3% | 65.1% | 57.9% |
United States. Losses incurred as a percent of direct premiums earned, countrywide, before reinsurance and not including loss adjustment expense. Source: National Association of Insurance Commissioners, Report on Profitability by Line by State in 2024, ten-year summary.
- Contractors pollution
- Disturbing old duct insulation and mastics can release asbestos, and leaking finished work feeds mold claims.
- Employment practices
- Field crews, seasonal hiring and subcontract labor bring wage, classification and harassment claims.
- Equipment breakdown
- A failed laser source or coil line controller stops duct output until parts arrive, though some work can be sent out.
| System | Code | Industry |
|---|---|---|
| NAICS 2022, primary | 332322 | Sheet Metal Work Manufacturing |
| NAICS 2022 | 238220 | Plumbing, Heating, and Air-Conditioning Contractors |
| NAICS 2022 | 238160 | Roofing Contractors |
| SIC 1987, primary | 3444 | Sheet Metal Work |
| SIC 1987 | 1711 | Plumbing, Heating, and Air-Conditioning |
| SIC 1987 | 1761 | Roofing, Siding, and Sheet Metal Work |
See this risk on the map.
Book a 30-minute walkthrough tailored to your portfolio and perils of interest.