Gear, bearing and power transmission manufacturers

These plants cut, heat treat and grind steel into gears, bearings, couplings and complete gearboxes for vehicles, aircraft, wind turbines and industrial drives. Oil-flooded cutting and quench furnaces create fire risk, and a cracked tooth or failed bearing can stop a plant or bring down an aircraft.

Manufacturing · NAICS 333612 · SIC 3566 · Updated November 2026

01 / Loss drivers

Where losses come from.

  1. 01

    Gear and bearing failures in service causing downtime, recalls or injury at the customer

  2. 02

    Quench oil and cutting oil fires in heat treatment and machining areas

  3. 03

    Loss of a hobbing or grinding machine that takes many months to replace

How it comparesEach line’s rating against the average for its NAICS sector, Manufacturing (178 business types), and for all 747.
  1. PropertyProperty: High, 4 of 5; sector average 3.7; all business types 2.9.
  2. Business interruptionBusiness interruption: High, 4 of 5; sector average 3.5; all business types 2.7.
  3. Premises liabilityPremises liability: Low, 1 of 5; sector average 1.9; all business types 2.7.
  4. Products and completed workProducts and completed work: High, 4 of 5; sector average 3.4; all business types 2.6.
  5. Workers’ injuryWorkers’ injury: Elevated, 3 of 5; sector average 3.4; all business types 3.0.
  6. Commercial autoCommercial auto: Moderate, 2 of 5; sector average 2.3; all business types 2.5.
  7. Crime and theftCrime and theft: Low, 1 of 5; sector average 1.9; all business types 2.2.
  8. Inland marine and equipmentInland marine and equipment: Moderate, 2 of 5; sector average 2.6; all business types 2.6.
  9. EnvironmentalEnvironmental: Elevated, 3 of 5; sector average 2.8; all business types 2.3.
  10. Cyber and dataCyber and data: Elevated, 3 of 5; sector average 2.7; all business types 2.7.
  11. Professional liabilityProfessional liability: Moderate, 2 of 5; sector average 1.5; all business types 2.0.
  12. Umbrella and excessUmbrella and excess: High, 4 of 5; sector average 3.6; all business types 3.6.
What’s changing
  • Electric vehicle drives need fewer but quieter and more precise gears, pushing makers toward hard finishing and new customers while traditional transmission work shrinks.
  • Larger wind turbines and industrial robots demand bigger and more precise gearboxes, concentrating value in a few large grinders with long replacement times.
  • Powder metal and printed gears and automated in-line inspection change how defects arise and how far back a failed part can be traced.
02 / Line by line

Twelve lines, rated.

Each line shows its rating and the reason for it; open a line for what to watch for and the controls that matter. Ratings are UrbanStat’s own editorial view of a typical business of this type, on a five-step scale. They are a starting point for questions, not a quote, a rate or a statistical measure.

Property

High
Hobbing and grinding run flooded with straight oil, and in-house carburizing adds furnaces, flammable atmospheres and open quench tanks.

Fire, explosion, water and weather damage to buildings, contents and stock.

Watch for
  • Quench tanks without overtemperature alarms, covers or fixed suppression
  • Oil mist coating roof structure above gear cutting machines
  • Furnace atmospheres with outdated burner and purge safeguards
Controls that matter
  • Fixed suppression, lids and oil temperature control on quench tanks
  • Mist extraction and machine-level extinguishing on oil-flooded machines
  • Furnace safety controls tested on a written schedule

Business interruption

High
Gear hobbers, shapers and profile grinders are built to order, and customers qualify one source for each gear.

How long and how costly a shutdown is.

Watch for
  • A single grinder or furnace that every premium job needs
  • Aerospace or automotive contracts with line-down penalties
  • Outside heat treater or forging supplier with no alternative
Controls that matter
  • Qualified second routes for heat treatment and grinding
  • Finished gear safety stock for contract customers

Premises liability

Low
Visitors are limited to customer auditors and delivery drivers.

Injuries to customers and the public, on site or caused by operations elsewhere.

Watch for
  • Drivers walking through production to reach the office
Controls that matter
  • Signed-in, escorted visitors and a separate driver entrance

Products and completed work

High
Gears carry the load in aircraft, vehicles, cranes, lifts and turbines, so a fatigue crack or wrong hardness has serious consequences.

Harm caused by what the business sells, serves, makes, installs or repairs.

Watch for
  • Aviation, rail, lift or steering applications in the order book
  • Grinding burn or case depth not checked on every batch
  • Design responsibility accepted for complete gearboxes
Controls that matter
  • Material, heat treatment and inspection records traceable to each serial
  • Hardness, case depth and grind-burn checks on every lot
  • Contract limits on consequential loss and recall costs

Workers’ injury

Elevated
Rotating cutters, heavy blanks and hot furnace loads cause cuts, crush injuries and burns, with oil mist and noise as chronic exposures.

Injuries and illness to employees.

Watch for
  • Manual loading of large blanks into machines
  • Operators reaching into quench areas without heat protection
Controls that matter
  • Hoists and manipulators at machines handling heavy parts
  • Interlocked enclosures on hobbers and grinders
  • Oil mist monitoring and skin care program

Commercial auto

Moderate
A light truck moves parts to outside processors and local customers; most freight goes by carrier.

Owned, hired and employee-driven vehicles, deliveries, customers’ vehicles in care.

Watch for
  • Regular shuttle runs to heat treaters or platers
Controls that matter
  • Driving record checks and proper load restraint for steel parts

Crime and theft

Low
Steel gears have little resale value; alloy scrap and carbide cutters are the only attractive items.

Burglary, robbery, employee dishonesty, cash, payment and invoice fraud.

Watch for
  • Scrap and carbide tooling sold informally for cash
Controls that matter
  • Scrap weighed and reconciled against sales records

Inland marine and equipment

Moderate
Finished gears travel by carrier, and customers send in gearboxes and gears for repair or regrinding.

Property in transit, at job sites or in the insured’s care, and mobile equipment.

Watch for
  • Large customer gearboxes held for rebuild
  • Precision ground gears shipped with poor corrosion or impact protection
Controls that matter
  • Bailee cover for customers' units under repair
  • Purpose-made crates and rust-preventive packing

Environmental

Elevated
Cutting oils, quench oil, alkaline washers, etching acids and legacy degreasing solvents leave oily floors, sumps and waste streams.

Pollution on or from the site or the work.

Watch for
  • Quench pits or sumps set below floor level
  • History of vapor degreasing with chlorinated solvents
Controls that matter
  • Lined pits with leak monitoring
  • Oil and coolant recycling with licensed disposal of sludge

Cyber and data

Elevated
Networked grinders, inspection machines and customer portals run production, and aerospace or defense work brings strict data handling obligations.

Data breaches, ransomware, system outages and attacks on connected equipment.

Watch for
  • Machine programs and gear geometry held only on networked controls
  • Defense or aerospace drawings handled without the required controls
  • Remote vendor access to grinders and furnace controls
Controls that matter
  • Offline, tested backups of programs, inspection data and lot records
  • Furnace and machine controls on a separate network segment

Professional liability

Moderate
Some makers design gearboxes and drives for customers' machines; a rating or selection error causes downtime claims rather than injury.

Loss or injury caused by advice, design, testing, care or another professional service.

Watch for
  • Application engineering and gearbox sizing done for customers
  • Field service, alignment and failure analysis sold as services
Controls that matter
  • Design calculations checked by a second engineer and kept on file
  • Contract limits on consequential loss and downtime

Umbrella and excess

High
A failed gear or bearing in an aircraft, lift, crane or vehicle steering can cause fatal accidents, and aviation claims exceed ordinary limits.

How likely one liability event is to exhaust primary limits.

Watch for
  • Flight-critical, elevator or crane hoist gearing in the order book
  • Wind turbine gearboxes, where one failure brings large repair claims
Controls that matter
  • Aviation products exposure placed on a separate, suitable policy
  • Layered limits matched to the most critical end use
03 / Property picture

Construction, occupancy, protection, exposure.

What a risk engineer expects to find at a typical site of this type, and what to compare a submission against.

Construction
Single-story steel or masonry plants with heavy floors and isolated foundations for grinders, overhead cranes, and a heat treat area with pits below floor level.
Occupancy
Hobbing, shaping and grinding flooded with straight oil, carburizing furnaces with flammable atmospheres and quench tanks, parts washers, and steel and oil storage.
Protection
Sprinklers throughout including over quench tanks, fixed suppression and lids on quench tanks, mist extraction, tested furnace safety controls and a monitored alarm.
Exposure
Usually in industrial parks near customers and outside heat treaters, where neighbors' storage and shared access roads matter more than the plant's own yard.
04 / Checklist

What to ask and look for.

Start with the desk review before quoting, then walk the site. Tick questions off as you go; ticks are kept in this browser only.

Before quoting: ask the broker or owner

Documents to request

On site: products and customers

On site: processes and protection

On site: quality and records

On site: people and site

Refer or decline if you find

  • Open quench tank with no temperature alarm or fixed suppression
  • Flight-critical or lifting gears made without full lot traceability
  • No test for grinding burn on hardened gears
  • Oil-soaked roof steel and no sprinklers
05 / Location

How UrbanStat data helps.

Gear grinders and hobbers are heavy precision machines set on isolated foundations. Flood or earthquake ruins their alignment, and water entering quench pits or oil sumps spreads contamination beyond the building.

FloodEarthquakeTornadoWind
  • Flood scores at the address show whether below-floor quench pits, oil sumps and precision grinders are exposed to rising water.
  • Parcel and permit data give the construction date and permit history, a quick check on building age and on when furnaces were added.
  • The risk analysis API returns earthquake and wind scores in seconds, so machine-heavy plants are screened for catastrophe exposure inside the quoting workflow.
Flood · Earthquake · Tornado · Wind
06 / Public loss data

What the published numbers say.

Official statistics for the industry or property type closest to this business. They describe the industry as a whole, not any one insured.

Workers’ injury frequency

1.4 recordable injuries and illnesses per 100 full-time workers, below the private-industry average of 2.3.

Speed changer, industrial high-speed drive, and gear manufacturing
1.4
All private industry
2.3

0.4 of these cases per 100 workers involved days away from work.

United States, 2024. Industry: Speed changer, industrial high-speed drive, and gear manufacturing (NAICS 333612). Source: U.S. Bureau of Labor Statistics, Survey of Occupational Injuries and Illnesses, Table 1: incidence rates of nonfatal occupational injuries and illnesses by industry and case types, 2024.

Workplace deaths

3 fatal work injuries in 2024.

Manufacturing
2.4
All workers
3.3

Deaths per 100,000 full-time equivalent workers, for the industry sector as a whole.

United States, private industry, 2024. Industry: Engine, Turbine, and Power Transmission Equipment Manufacturing (NAICS 33361), the closest published group. Source: U.S. Bureau of Labor Statistics, Census of Fatal Occupational Injuries; sector rates.

Most cited safety standards

17 citations from 5 inspections; 41% were classed serious, willful or repeat.

  • 1910.107 Spray finishing using flammable and combustible materials
    4
  • 1910.147 The control of hazardous energy (lockout/tagout)
    3
  • 1910.215 Abrasive wheel machinery
    1
  • 1910.1200 Hazard communication
    1

Standards cited most often in this industry, by number of citations.

United States, citations issued October 2024 to September 2025 (federal fiscal year 2025). Industry: Speed Changer, Industrial High-Speed Drive, and Gear Manufacturing (NAICS 333612). Covers federal and state-plan inspections. A citation is one violation item; one inspection can produce several. Source: U.S. Department of Labor, Occupational Safety and Health Administration, OSHA enforcement data (inspections and violations); standard titles from the Code of Federal Regulations, Title 29 (section headings).

Fire frequency

7,966 fires a year reported in industrial and manufacturing properties, causing about $810 million in direct property damage a year.

United States, 2020 to 2024, annual average. The group includes utility, defense, agriculture and mining properties. Source: National Fire Protection Association, Structure Fires in Industrial and Manufacturing Properties.

Toxic chemical releases

19 facilities reported toxic chemical releases totaling 43,836 pounds on and off site.

  • Ammonia
    32,627
  • Methanol
    9,250
  • Nickel
    1,116

Chemicals released in the largest amounts, in pounds. 14 of the facilities reported at least one chemical classed as a carcinogen.

United States, 2024. Industry: Speed Changer, Industrial High-Speed Drive, and Gear Manufacturing (NAICS 333612). Covers facilities in listed industries with ten or more full-time employees that handle listed chemicals above set thresholds. Source: U.S. Environmental Protection Agency, Toxics Release Inventory basic data files.

Industry loss ratios by line2020 to 2024, the same table on every guide

Loss ratios are published by line of insurance, not by business type. They show how each line has run for insurers as a whole, whatever the business insured.

Published lineClosest line in this guide20202021202220232024
FireProperty63.2%67.3%62.4%45.5%40.9%
Commercial multiple perilProperty and liability sold as a package61.2%60.2%59.4%61.2%54.4%
Inland marineInland marine and equipment64.5%49.4%47.1%44.1%44.0%
Other liabilityPremises liability, and most umbrella, professional (other than medical) and cyber cover65.1%58.8%61.0%63.7%71.2%
Products liabilityProducts and completed work48.2%52.2%46.0%57.5%60.3%
Workers’ compensationWorkers’ injury47.9%49.2%45.0%44.3%46.0%
Commercial auto liabilityCommercial auto68.3%66.5%71.9%76.8%77.6%
Commercial auto physical damageCommercial auto50.9%56.3%64.3%65.1%57.9%

United States. Losses incurred as a percent of direct premiums earned, countrywide, before reinsurance and not including loss adjustment expense. Source: National Association of Insurance Commissioners, Report on Profitability by Line by State in 2024, ten-year summary.

Coverages to raise
Equipment breakdown
Hobbers, profile grinders and carburizing furnaces fail mechanically and take many months to replace.
Product recall
Customers bill the maker for removing and replacing suspect gears or bearings already built into machines and vehicles.
Aircraft products and grounding
Standard liability forms exclude aircraft products, and a suspect gear can ground a whole fleet.
Contingent business interruption
A fire at the forging supplier or outside heat treater stops deliveries even when the plant is untouched.
Pollution legal liability
Quench pits, oil sumps and past solvent degreasing leave contamination that general liability excludes.
Classification
SystemCodeIndustry
NAICS 2022, primary333612Speed Changer, Industrial High-Speed Drive, and Gear Manufacturing
NAICS 2022333613Mechanical Power Transmission Equipment Manufacturing
NAICS 2022336350Motor Vehicle Transmission and Power Train Parts Manufacturing
NAICS 2022332991Ball and Roller Bearing Manufacturing
NAICS 2022336412Aircraft Engine and Engine Parts Manufacturing
SIC 1987, primary3566Speed Changers, Industrial High-Speed Drives, and Gears
SIC 19873568Mechanical Power Transmission Equipment, NEC
SIC 19873562Ball and Roller Bearings
Next step

See this risk on the map.

Book a 30-minute walkthrough tailored to your portfolio and perils of interest.

Request a Demo →