Commercial heat treaters

Commercial heat treaters harden, temper, anneal and case-harden other manufacturers' parts in atmosphere, vacuum and salt-bath furnaces, usually quenching in oil. Flammable furnace gases and large open oil tanks make fire the dominant hazard, and a wrong cycle silently ruins safety-critical parts.

Manufacturing · NAICS 332811 · SIC 3398 · Updated November 2026

01 / Loss drivers

Where losses come from.

  1. 01

    Quench oil fires when a hot load hangs up or water gets into the tank

  2. 02

    Explosions of flammable furnace atmospheres and violent eruptions from molten salt baths

  3. 03

    Mis-treated parts that crack or wear out early in customers' products

How it comparesEach line’s rating against the average for its NAICS sector, Manufacturing (178 business types), and for all 747.
  1. PropertyProperty: High, 4 of 5; sector average 3.7; all business types 2.9.
  2. Business interruptionBusiness interruption: High, 4 of 5; sector average 3.5; all business types 2.7.
  3. Premises liabilityPremises liability: Low, 1 of 5; sector average 1.9; all business types 2.7.
  4. Products and completed workProducts and completed work: High, 4 of 5; sector average 3.4; all business types 2.6.
  5. Workers’ injuryWorkers’ injury: Elevated, 3 of 5; sector average 3.4; all business types 3.0.
  6. Commercial autoCommercial auto: Moderate, 2 of 5; sector average 2.3; all business types 2.5.
  7. Crime and theftCrime and theft: Low, 1 of 5; sector average 1.9; all business types 2.2.
  8. Inland marine and equipmentInland marine and equipment: Elevated, 3 of 5; sector average 2.6; all business types 2.6.
  9. EnvironmentalEnvironmental: Elevated, 3 of 5; sector average 2.8; all business types 2.3.
  10. Cyber and dataCyber and data: Elevated, 3 of 5; sector average 2.7; all business types 2.7.
  11. Professional liabilityProfessional liability: Elevated, 3 of 5; sector average 1.5; all business types 2.0.
  12. Umbrella and excessUmbrella and excess: High, 4 of 5; sector average 3.6; all business types 3.6.
What’s changing
  • Vacuum furnaces with gas quench and low-pressure carburizing replace oil and salt in many plants, lowering fire load but concentrating value in costly equipment.
  • Aerospace and medical customers demand electronic temperature records and audits, so data loss or a missed furnace survey can void a whole load.
  • Rising energy costs push plants toward induction and electric furnaces, shifting the hazard from gas explosions toward power quality and outages.
02 / Line by line

Twelve lines, rated.

Each line shows its rating and the reason for it; open a line for what to watch for and the controls that matter. Ratings are UrbanStat’s own editorial view of a typical business of this type, on a five-step scale. They are a starting point for questions, not a quote, a rate or a statistical measure.

Property

High
Hot loads plunge into large tanks of oil beside furnaces filled with hydrogen-rich gas; a stuck elevator starts a major fire.

Fire, explosion, water and weather damage to buildings, contents and stock.

Watch for
  • Integral quench furnaces without tested safety interlocks
  • Water-cooled oil coolers that can leak into the quench tank
  • Oil residue coating roof steel, ducts and exhaust hoods
Controls that matter
  • Burner, atmosphere and purge safeguards tested by a combustion specialist
  • Oil temperature, level and water-content checks with over-temperature cut-outs
  • Fixed fire protection over quench tanks, with hoods and ducts cleaned

Business interruption

High
Furnaces are built to order and customer approvals attach to this site, so work moves to competitors and may not return.

How long and how costly a shutdown is.

Watch for
  • One vacuum or large batch furnace carrying key contracts
  • Aerospace or medical approvals tied to specific equipment
  • Dependence on a single gas or electricity supply
Controls that matter
  • Spare elements, fans, pumps and controls for critical furnaces
  • Pre-qualified second site or reciprocal treater
  • Furnace recipes and certification records backed up off site

Premises liability

Low
Industrial premises with only customers' drivers and auditors visiting.

Injuries to customers and the public, on site or caused by operations elsewhere.

Watch for
  • Drivers entering the shop floor near hot baskets
Controls that matter
  • Collections handled at a separate dock

Products and completed work

High
Treatment sets the strength of gears, fasteners, springs and landing gear; an error is invisible until parts fail.

Harm caused by what the business sells, serves, makes, installs or repairs.

Watch for
  • Aerospace, vehicle safety, firearm or medical implant parts
  • High-strength steels sensitive to embrittlement and cracking
  • Certificates issued without hardness or metallurgical checks
Controls that matter
  • Calibrated temperature instruments, furnace surveys and recorded cycle charts
  • Hardness and case depth testing on every load
  • Terms limiting liability to the cost of re-treatment

Workers’ injury

Elevated
Burns, strains from loading heavy baskets and fixtures, heat stress and exposure to oil smoke and furnace gases.

Injuries and illness to employees.

Watch for
  • Manual loading and unloading of hot fixtures
  • Damp or cold parts and fixtures lowered into molten salt
  • Entry into furnaces or pits for maintenance
Controls that matter
  • Charge cars, hoists and manipulators for loads
  • Preheating of parts and tools before salt bath immersion
  • Confined space, gas testing and lockout procedures

Commercial auto

Moderate
Many shops run a truck or two collecting and returning customers' parts on local routes.

Owned, hired and employee-driven vehicles, deliveries, customers’ vehicles in care.

Watch for
  • Daily pickup routes with dense, heavy bins
Controls that matter
  • Bins secured against shifting and drivers' records checked

Crime and theft

Low
Nothing in the shop is easy to resell, and no cash is handled.

Burglary, robbery, employee dishonesty, cash, payment and invoice fraud.

Watch for
  • Customers' high-value alloy parts left on an open dock
Controls that matter
  • Controlled receiving area with signed transfers

Inland marine and equipment

Elevated
Every part in the building belongs to a customer, and a single furnace load of aerospace parts can be worth more than the furnace.

Property in transit, at job sites or in the insured’s care, and mobile equipment.

Watch for
  • No terms limiting liability for customers' parts
  • Peak values of work on the floor unknown
Controls that matter
  • Bailee cover set from tracked work-in-progress values
  • Signed terms of business with a stated liability limit

Environmental

Elevated
Quench oils, spent salts including cyanide-bearing types, ammonia, cleaning solvents and oily wash water are all regulated.

Pollution on or from the site or the work.

Watch for
  • Cyanide or barium salt baths
  • Underground quench oil pits or tanks
  • Vapor degreasing before or after treatment
Controls that matter
  • Segregated storage and licensed disposal for incompatible salts
  • Pit leak testing or double containment
  • Aqueous washers with oil skimming

Cyber and data

Elevated
Furnace recipes, controllers and the temperature records customers require are networked; lost records can mean whole loads cannot be certified.

Data breaches, ransomware, system outages and attacks on connected equipment.

Watch for
  • Furnace controllers reachable remotely by vendors or from the office network
  • Electronic cycle records kept only on one local server
Controls that matter
  • Segmented control network with logged, multi-factor vendor access
  • Cycle charts and certificates backed up off site daily

Professional liability

Elevated
Metallurgists choose cycles and sign certificates that customers rely on, so a wrong process choice or false pass is a professional error.

Loss or injury caused by advice, design, testing, care or another professional service.

Watch for
  • In-house metallurgical lab issuing hardness and failure analysis reports
  • Treaters recommending processes when customer specifications are unclear
Controls that matter
  • Written process approval signed by the customer before first run
  • Calibrated lab equipment and peer review of failure reports

Umbrella and excess

High
A batch of brittle aerospace bolts or steering parts can cause fatal failures, and every part from that load is suspect.

How likely one liability event is to exhaust primary limits.

Watch for
  • Aerospace, vehicle safety or lifting parts as a large share of work
Controls that matter
  • Limits set by the most severe end use, including aircraft products cover
03 / Property picture

Construction, occupancy, protection, exposure.

What a risk engineer expects to find at a typical site of this type, and what to compare a submission against.

Construction
Single-story steel-framed buildings with high bays, crane runways and pits for quench tanks and deep furnaces, often older plants with roof steel coated in oil residue.
Occupancy
Gas-fired and electric furnaces with flammable endothermic or hydrogen atmospheres, open oil quench tanks, molten salt baths, ammonia for nitriding and baskets of customers' parts.
Protection
Tested burner and atmosphere safeguards, fixed suppression over quench tanks, over-temperature and water detection on oil, sprinklers in the building, and a monitored alarm.
Exposure
Plants sit among the manufacturers they serve in industrial districts, and bulk nitrogen, hydrogen or ammonia tanks outside the building add an explosion source near neighbors.
04 / Checklist

What to ask and look for.

Start with the desk review before quoting, then walk the site. Tick questions off as you go; ticks are kept in this browser only.

Before quoting: ask the broker or owner

Documents to request

On site: work and customers

On site: furnaces and quenching

On site: quality

On site: people and environment

Refer or decline if you find

  • Quench tanks with no fixed fire protection
  • Furnace safety interlocks jumpered or untested
  • No signed terms limiting liability for customers' parts
  • Cyanide and nitrate salts stored together
  • Certificates issued without testing each load
05 / Location

How UrbanStat data helps.

Quench tanks and furnace pits are below floor level; flood water in hot oil or molten salt causes eruptions and spreads contamination. Shaking can slosh oil tanks and rupture gas lines to furnaces.

FloodEarthquakeTornadoWind
  • Flood scores at the address show whether water could reach below-floor quench tanks and salt baths, where it causes eruptions and carries oil off site.
  • Earthquake scores at the address indicate how exposed open oil tanks and furnace gas piping are to sloshing and rupture.
  • Parcel and permit data give building age and permit history, a check on when furnaces, gas services and fire protection were last formally altered.
Flood · Earthquake · Tornado · Wind
06 / Public loss data

What the published numbers say.

Official statistics for the industry or property type closest to this business. They describe the industry as a whole, not any one insured.

Workers’ injury frequency

3.3 recordable injuries and illnesses per 100 full-time workers, above the private-industry average of 2.3.

Metal heat treating
3.3
All private industry
2.3

1.8 of these cases per 100 workers involved days away from work.

United States, 2024. Industry: Metal heat treating (NAICS 332811). Source: U.S. Bureau of Labor Statistics, Survey of Occupational Injuries and Illnesses, Table 1: incidence rates of nonfatal occupational injuries and illnesses by industry and case types, 2024.

Workplace deaths

7 fatal work injuries in 2024.

Manufacturing
2.4
All workers
3.3

Deaths per 100,000 full-time equivalent workers, for the industry sector as a whole.

United States, private industry, 2024. Industry: Coating, Engraving, Heat Treating, and Allied Activities (NAICS 33281), the closest published group. Source: U.S. Bureau of Labor Statistics, Census of Fatal Occupational Injuries; sector rates.

Most cited safety standards

91 citations from 23 inspections; 57% were classed serious, willful or repeat.

  • 1910.134 Respiratory protection
    8
  • 1910.212 General requirements for all machines
    5
  • 1910.146 Permit-required confined spaces
    5
  • 1910.28 Duty to have fall protection and falling object protection
    4
  • 1910.215 Abrasive wheel machinery
    4

Standards cited most often in this industry, by number of citations.

United States, citations issued October 2024 to September 2025 (federal fiscal year 2025). Industry: Metal Heat Treating (NAICS 332811). Covers federal and state-plan inspections. A citation is one violation item; one inspection can produce several. Source: U.S. Department of Labor, Occupational Safety and Health Administration, OSHA enforcement data (inspections and violations); standard titles from the Code of Federal Regulations, Title 29 (section headings).

Fire frequency

7,966 fires a year reported in industrial and manufacturing properties, causing about $810 million in direct property damage a year.

United States, 2020 to 2024, annual average. The group includes utility, defense, agriculture and mining properties. Source: National Fire Protection Association, Structure Fires in Industrial and Manufacturing Properties.

Toxic chemical releases

98 facilities reported toxic chemical releases totaling 692,021 pounds on and off site.

  • Barium and barium compounds
    197,340
  • Ammonia
    189,147
  • Nitrate compounds
    97,861

Chemicals released in the largest amounts, in pounds. 14 of the facilities reported at least one chemical classed as a carcinogen.

United States, 2024. Industry: Metal Heat Treating (NAICS 332811). Covers facilities in listed industries with ten or more full-time employees that handle listed chemicals above set thresholds. Source: U.S. Environmental Protection Agency, Toxics Release Inventory basic data files.

Industry loss ratios by line2020 to 2024, the same table on every guide

Loss ratios are published by line of insurance, not by business type. They show how each line has run for insurers as a whole, whatever the business insured.

Published lineClosest line in this guide20202021202220232024
FireProperty63.2%67.3%62.4%45.5%40.9%
Commercial multiple perilProperty and liability sold as a package61.2%60.2%59.4%61.2%54.4%
Inland marineInland marine and equipment64.5%49.4%47.1%44.1%44.0%
Other liabilityPremises liability, and most umbrella, professional (other than medical) and cyber cover65.1%58.8%61.0%63.7%71.2%
Products liabilityProducts and completed work48.2%52.2%46.0%57.5%60.3%
Workers’ compensationWorkers’ injury47.9%49.2%45.0%44.3%46.0%
Commercial auto liabilityCommercial auto68.3%66.5%71.9%76.8%77.6%
Commercial auto physical damageCommercial auto50.9%56.3%64.3%65.1%57.9%

United States. Losses incurred as a percent of direct premiums earned, countrywide, before reinsurance and not including loss adjustment expense. Source: National Association of Insurance Commissioners, Report on Profitability by Line by State in 2024, ten-year summary.

Coverages to raise
Equipment breakdown
Vacuum pumps, furnace elements, fans and controls fail without fire, and replacement furnaces are built to order.
Bailee customers' goods
Customers' parts damaged by fire, quench or a wrong cycle are claimed against the treater, often far above the fee.
Product recall
A wrong cycle on a batch of safety parts leaves customers recalling assemblies, a cost general liability excludes.
Site pollution liability
Spent salts, quench oil in pits and ammonia releases create cleanup claims that general liability excludes.
Utility service interruption
Loss of gas, power or nitrogen supply ruins loads in process and stops furnaces that cannot restart quickly.
Classification
SystemCodeIndustry
NAICS 2022, primary332811Metal Heat Treating
SIC 1987, primary3398Metal Heat Treating
Next step

See this risk on the map.

Book a 30-minute walkthrough tailored to your portfolio and perils of interest.

Request a Demo →