Steel millsNAICS 331110 · SIC 3312

Steel mills melt scrap or reduce iron ore, refine and cast the liquid steel, then roll it into plate, coil, bar and sections; re-rollers and pipe and tube mills work purchased steel. Huge volumes of molten metal, high-voltage furnaces, large hydraulic systems and overhead cranes make losses infrequent but very large.

NAICS 331110 Iron and Steel Mills and Ferroalloy ManufacturingSIC 3312 Steel Works, Blast FurnacesNAICS 331221 Rolled Steel Shape ManufacturingNAICS 331210 Iron and Steel Pipe and Tube Manufacturing from Purchased Steel+2 more codes

Manufacturing · Updated November 2026

01 / Loss drivers

Where losses come from.

  1. 01

    Molten metal breakouts and steam explosions at furnaces, ladles and casters

  2. 02

    Hydraulic oil, transformer and cable fires in rolling mills and electrical rooms

  3. 03

    Fatal and disabling injuries from cranes, hot metal, gas and moving stock

How it comparesEach line’s rating against the average for its NAICS sector, Manufacturing (178 business types), and for all 747.
  1. PropertyProperty: High, 4 of 5; sector average 3.7; all business types 2.9.
  2. Business interruptionBusiness interruption: Severe, 5 of 5; sector average 3.5; all business types 2.7.
  3. Premises liabilityPremises liability: Moderate, 2 of 5; sector average 1.9; all business types 2.7.
  4. Products and completed workProducts and completed work: Elevated, 3 of 5; sector average 3.4; all business types 2.6.
  5. Workers’ injuryWorkers’ injury: High, 4 of 5; sector average 3.4; all business types 3.0.
  6. Commercial autoCommercial auto: Elevated, 3 of 5; sector average 2.3; all business types 2.5.
  7. Crime and theftCrime and theft: Moderate, 2 of 5; sector average 1.9; all business types 2.2.
  8. Inland marine and equipmentInland marine and equipment: Elevated, 3 of 5; sector average 2.6; all business types 2.6.
  9. EnvironmentalEnvironmental: High, 4 of 5; sector average 2.8; all business types 2.3.
  10. Cyber and dataCyber and data: Elevated, 3 of 5; sector average 2.7; all business types 2.7.
  11. Professional liabilityProfessional liability: Low, 1 of 5; sector average 1.5; all business types 2.0.
  12. Umbrella and excessUmbrella and excess: High, 4 of 5; sector average 3.6; all business types 3.6.
What’s changing
  • Electric arc furnaces fed with scrap and direct-reduced iron are replacing blast furnaces, concentrating risk in transformers, power supply and scrap screening.
  • Hydrogen-based iron reduction and carbon capture projects bring new gas hazards and expensive, first-of-a-kind equipment with uncertain replacement times.
  • Scrap streams contain more lithium-ion batteries, sealed cylinders and mixed alloys, raising explosion risk at charging and demanding tighter grade control.
02 / Line by line

Twelve lines, rated.

Each line shows its rating and the reason for it; open a line for what to watch for and the controls that matter. Ratings are UrbanStat’s own editorial view of a typical business of this type, on a five-step scale. They are a starting point for questions, not a quote, a rate or a statistical measure.

Property

High
Liquid steel, furnace transformers, oil-filled hydraulics and cable tunnels sit together; one breakout or oil fire damages very costly plant.

Fire, explosion, water and weather damage to buildings, contents and stock.

Watch for
  • Water leaks from furnace panels or lances into the melt
  • Wet or sealed scrap charged without screening
  • Unprotected hydraulic cellars, cable tunnels and cold mill rolling-oil exhaust ducts
Controls that matter
  • Leak detection on water-cooled panels with emergency furnace procedures
  • Fixed fire protection for hydraulic rooms, transformers and cable tunnels
  • Breakout detection on casters and containment pits kept dry

Business interruption

Severe
Melt shop, caster and hot mill run in series; losing a furnace transformer or mill drive stops everything for months.

How long and how costly a shutdown is.

Watch for
  • Single furnace or single caster with no bypass route
  • No spare furnace transformer or main mill motor
  • Customers in vehicle or appliance supply chains with penalty clauses
Controls that matter
  • Critical spares on site, tested and ready to install
  • Ability to buy slab or billet and keep rolling
  • Condition monitoring of transformers, gearboxes and crane hoists

Premises liability

Moderate
Sites are fenced and remote from the public, but large numbers of contractors, haulers and rail crews work inside.

Injuries to customers and the public, on site or caused by operations elsewhere.

Watch for
  • Major shutdown work by outside contractors
  • Slag or dust nuisance reaching neighbors
Controls that matter
  • Contractor prequalification, induction and permit-to-work systems
  • Indemnity and insurance terms in all service contracts

Products and completed work

Elevated
Steel goes into structures, pressure equipment and vehicles; off-grade heats are usually caught, but a miss spreads widely.

Harm caused by what the business sells, serves, makes, installs or repairs.

Watch for
  • Plate, pipe or bar sold for pressure, rail or safety-critical uses
  • Mill certificates issued by the same team that ships the product
  • Radioactive sources melted from scrap
Controls that matter
  • Heat-by-heat chemistry and mechanical testing with full traceability
  • Independent sign-off of test certificates
  • Radiation portals on every inbound scrap load

Workers’ injury

High
Fewer workers than in the past, but the hazards are lethal: ladle cranes, liquid metal, carbon monoxide, hot coil and rail movements.

Injuries and illness to employees.

Watch for
  • People on foot in crane bays and scrap yards
  • Maintenance inside furnaces, ducts and gas lines
  • Long shifts and heat exposure in the melt shop
Controls that matter
  • Exclusion zones and remote operation at tapping and casting
  • Gas monitoring, lockout and confined space permits
  • Crane inspection and certified operators for hot metal lifts

Commercial auto

Elevated
Scrap arrives and product leaves by heavy truck and rail; mills often own shuttle trucks and locomotives.

Owned, hired and employee-driven vehicles, deliveries, customers’ vehicles in care.

Watch for
  • Own fleet hauling coil or long products on public roads
  • Internal haul vehicles crossing public roads
Controls that matter
  • Coil and bundle securing rules enforced at the gate
  • Driver qualification and maintenance records for owned trucks

Crime and theft

Moderate
Alloying metals, copper and electrodes are valuable, and scrap buying invites weight and grade fraud.

Burglary, robbery, employee dishonesty, cash, payment and invoice fraud.

Watch for
  • Nickel, molybdenum and other alloys stored without stock control
  • Scrap graded and paid by the same person
Controls that matter
  • Locked alloy stores with reconciled usage
  • Segregated weighing, grading and payment for scrap

Inland marine and equipment

Elevated
Slag pot carriers, loaders, locomotives and mobile cranes are large values, and product moves by rail, barge and ship.

Property in transit, at job sites or in the insured’s care, and mobile equipment.

Watch for
  • Mobile equipment working around hot slag
  • Export cargoes and stock at outside processors
Controls that matter
  • Fire suppression on mobile plant in hot areas
  • Cargo and off-site stock declared and tracked

Environmental

High
Furnace dust is a hazardous waste, and slag, mill scale, pickling acid, oils and cooling water all need managed disposal.

Pollution on or from the site or the work.

Watch for
  • Furnace dust stored outdoors or landfilled on site
  • Acid pickling lines and old lagoons
  • Long industrial history on the same land
Controls that matter
  • Baghouses with dust sent to licensed recycling
  • Acid regeneration and treated, recirculated process water
  • Groundwater monitoring and diked oil storage

Cyber and data

Elevated
Furnace, caster and mill automation run on networked controls; an attack mid-heat can force an unsafe stop and weeks of downtime.

Data breaches, ransomware, system outages and attacks on connected equipment.

Watch for
  • Control systems reachable from office networks or vendor remote access
  • Unsupported operating systems on furnace and mill controllers
Controls that matter
  • Segmented control networks with monitored vendor access
  • Offline backups of control logic and a tested safe shutdown

Professional liability

Low
Little advice is sold; grade selection and metallurgical support for customers come with the steel.

Loss or injury caused by advice, design, testing, care or another professional service.

Watch for
  • Metallurgical testing or consulting sold to outside clients
Controls that matter
  • Sales terms disclaiming advice beyond the stated grade and specification

Umbrella and excess

High
A breakout or explosion during a contractor shutdown, a coil falling from a truck or a gas release can injure many.

How likely one liability event is to exhaust primary limits.

Watch for
  • Shutdowns with large contractor crews near hot metal and cranes
  • Fuel gas lines and holders near the site boundary
Controls that matter
  • Contractor permit system enforced through every outage
  • Gas detection and emergency plans shared with neighbors
03 / Property picture

Construction, occupancy, protection, exposure.

What a risk engineer expects to find at a typical site of this type, and what to compare a submission against.

Construction
Very large steel-frame melt shops and rolling mill halls with crane runways, below-grade pits and hydraulic cellars, long cable tunnels and older roofs with combustible insulation.
Occupancy
Liquid steel in furnaces, ladles and casters beside water cooling, high-voltage furnace transformers, oil-filled hydraulics and lubrication systems, fuel gases, and hot coil and bar.
Protection
Fixed protection in hydraulic cellars, cable tunnels and transformer bays, dry breakout pits, water leak detection on furnaces, a site fire brigade and a reliable fire water supply.
Exposure
Mills sit on large industrial sites by rivers, harbors and rail, often beside processors, slag handlers and gas plants that add fire and explosion exposure.
04 / Checklist

What to ask and look for.

Start with the desk review before quoting, then walk the site. Tick questions off as you go; ticks are kept in this browser only.

Before quoting: ask the broker or owner

Documents to request

On site: melt shop and casting

On site: mills and electrical

On site: continuity

On site: people and environment

Refer or decline if you find

  • No spare furnace transformer and no sourcing plan
  • Hydraulic cellars and cable tunnels without fixed protection
  • Scrap charged without moisture or radiation checks
  • Recent breakout or steam explosion with causes unresolved
05 / Location

How UrbanStat data helps.

Mills sit beside rivers and harbors for water and transport, so flood and surge threaten pits, cellars and furnaces holding liquid metal. Tall crane buildings and stacks are exposed to wind and shaking.

FloodEarthquakeHurricaneStorm surgeWind
  • Flood and storm surge scores at the address show whether water could reach furnace pits and hydraulic cellars at waterside mills.
  • Street-by-street exposure views show how much insured value sits at the mill and the processors and suppliers clustered around it, with alerts when a threshold is passed.
  • Live event overlays show whether a mill lies in a hurricane's forecast track, where an orderly shutdown takes time and a forced one damages plant.
Flood · Earthquake · Hurricane · Storm surge
06 / Public loss data · NAICS 331110

What the published numbers say.

Official statistics for the industry or property type closest to this business. They describe the industry as a whole, not any one insured.

Workers’ injury frequency

1.9 recordable injuries and illnesses per 100 full-time workers, close to the private-industry average of 2.3.

Iron and steel mills and ferroalloy manufacturing
1.9
All private industry
2.3

0.6 of these cases per 100 workers involved days away from work.

United States, 2024. Industry: Iron and steel mills and ferroalloy manufacturing (NAICS 3311), the closest published group. Source: U.S. Bureau of Labor Statistics, Survey of Occupational Injuries and Illnesses, Table 1: incidence rates of nonfatal occupational injuries and illnesses by industry and case types, 2024.

Workplace deaths

15 fatal work injuries in 2024, most often from contact with objects and equipment (6).

Manufacturing
2.4
All workers
3.3

Deaths per 100,000 full-time equivalent workers, for the industry sector as a whole.

United States, private industry, 2024. Industry: Primary Metal Manufacturing (NAICS 331), the closest published group. Source: U.S. Bureau of Labor Statistics, Census of Fatal Occupational Injuries; sector rates.

Most cited safety standards

109 citations from 45 inspections; 54% were classed serious, willful or repeat.

  • 1910.147 The control of hazardous energy (lockout/tagout)
    17
  • 1910.303 General (electrical)
    12
  • 1910.305 Wiring methods, components, and equipment for general use
    7
  • 1910.1200 Hazard communication
    6
  • 1910.134 Respiratory protection
    6

Standards cited most often in this industry, by number of citations.

United States, citations issued October 2024 to September 2025 (federal fiscal year 2025). Industry: Iron and Steel Mills and Ferroalloy Manufacturing (NAICS 331110). Covers federal and state-plan inspections. A citation is one violation item; one inspection can produce several. Source: U.S. Department of Labor, Occupational Safety and Health Administration, OSHA enforcement data (inspections and violations); standard titles from the Code of Federal Regulations, Title 29 (section headings).

Fire frequency

7,966 fires a year reported in industrial and manufacturing properties, causing about $810 million in direct property damage a year.

United States, 2020 to 2024, annual average. The group includes utility, defense, agriculture and mining properties. Source: National Fire Protection Association, Structure Fires in Industrial and Manufacturing Properties.

Toxic chemical releases

137 facilities reported toxic chemical releases totaling 117.4 million pounds on and off site.

  • Zinc compounds
    37.2M
  • Manganese and manganese compounds
    30.5M
  • Nitrate compounds
    14.6M

Chemicals released in the largest amounts, in pounds. 127 of the facilities reported at least one chemical classed as a carcinogen.

United States, 2024. Industry: Iron and Steel Mills and Ferroalloy Manufacturing (NAICS 331110). Covers facilities in listed industries with ten or more full-time employees that handle listed chemicals above set thresholds. Source: U.S. Environmental Protection Agency, Toxics Release Inventory basic data files.

Industry loss ratios by line2020 to 2024, the same table on every guide

Loss ratios are published by line of insurance, not by business type. They show how each line has run for insurers as a whole, whatever the business insured.

Published lineClosest line in this guide20202021202220232024
FireProperty63.2%67.3%62.4%45.5%40.9%
Commercial multiple perilProperty and liability sold as a package61.2%60.2%59.4%61.2%54.4%
Inland marineInland marine and equipment64.5%49.4%47.1%44.1%44.0%
Other liabilityPremises liability, and most umbrella, professional (other than medical) and cyber cover65.1%58.8%61.0%63.7%71.2%
Products liabilityProducts and completed work48.2%52.2%46.0%57.5%60.3%
Workers’ compensationWorkers’ injury47.9%49.2%45.0%44.3%46.0%
Commercial auto liabilityCommercial auto68.3%66.5%71.9%76.8%77.6%
Commercial auto physical damageCommercial auto50.9%56.3%64.3%65.1%57.9%

United States. Losses incurred as a percent of direct premiums earned, countrywide, before reinsurance and not including loss adjustment expense. Source: National Association of Insurance Commissioners, Report on Profitability by Line by State in 2024, ten-year summary.

Coverages to raise
Equipment breakdown
Furnace transformers, mill drives and large gearboxes fail without fire, and replacements can take many months.
Contingent business interruption
Mills depend on a few suppliers of scrap, ore, electrodes and power, and on large customers.
Site pollution liability
Furnace dust, pickling acid, mill scale and old lagoons create pollution claims general liability excludes.
Product recall
Off-grade steel built into vehicle, pipeline or pressure parts can force customers to recall and replace finished goods.
Utility service interruption
A grid outage off the premises stops arc furnaces at once and can freeze metal in ladles.

NAICS and SIC codes for steel mills

SystemCodeIndustry
NAICS 2022, primary331110Iron and Steel Mills and Ferroalloy Manufacturing
NAICS 2022331221Rolled Steel Shape Manufacturing
NAICS 2022331210Iron and Steel Pipe and Tube Manufacturing from Purchased Steel
SIC 1987, primary3312Steel Works, Blast Furnaces
SIC 19873316Cold-Rolled Steel Sheet, Strip, and Bars
SIC 19873317Steel Pipe and Tubes
Next step

See this risk on the map.

Book a 30-minute walkthrough tailored to your portfolio and perils of interest.

Request a Demo →