FoundriesNAICS 331511 · SIC 3321
Foundries melt iron, steel, aluminum, brass or other alloys and pour or inject the metal into sand, ceramic or steel molds. Liquid metal, moisture, combustible binders and hydraulic oil share the same floor, and the workforce faces heat, dust, noise and heavy handling every shift.
NAICS 331511 Iron FoundriesSIC 3321 Gray and Ductile Iron FoundriesNAICS 331523 Nonferrous Metal Die-Casting FoundriesNAICS 331524 Aluminum Foundries (except Die-Casting)+6 more codes
Where losses come from.
- 01
Molten metal run-outs, spills and steam explosions at furnaces, ladles and molds
- 02
Burns, silica disease, strains and hand injuries among melting, molding and finishing staff
- 03
Fires in hydraulic die-casting machines, core rooms, pattern stores and dust collectors
- PropertyProperty: High, 4 of 5; sector average 3.7; all business types 2.9.
- Business interruptionBusiness interruption: High, 4 of 5; sector average 3.5; all business types 2.7.
- Premises liabilityPremises liability: Moderate, 2 of 5; sector average 1.9; all business types 2.7.
- Products and completed workProducts and completed work: Elevated, 3 of 5; sector average 3.4; all business types 2.6.
- Workers’ injuryWorkers’ injury: Severe, 5 of 5; sector average 3.4; all business types 3.0.
- Commercial autoCommercial auto: Moderate, 2 of 5; sector average 2.3; all business types 2.5.
- Crime and theftCrime and theft: Moderate, 2 of 5; sector average 1.9; all business types 2.2.
- Inland marine and equipmentInland marine and equipment: Elevated, 3 of 5; sector average 2.6; all business types 2.6.
- EnvironmentalEnvironmental: High, 4 of 5; sector average 2.8; all business types 2.3.
- Cyber and dataCyber and data: Elevated, 3 of 5; sector average 2.7; all business types 2.7.
- Professional liabilityProfessional liability: Moderate, 2 of 5; sector average 1.5; all business types 2.0.
- Umbrella and excessUmbrella and excess: High, 4 of 5; sector average 3.6; all business types 3.6.
- Vehicle makers are casting large single-piece body structures in huge die-casting cells, concentrating value, hydraulic fire load and interruption risk in few machines.
- Rules on silica and metal fume keep tightening, pushing foundries toward mechanized finishing, enclosed shakeout and medical surveillance, while legacy disease claims still emerge.
- Printed sand molds and cores cut pattern storage and lead times, but bring printer resins and costly new equipment into the core room.
Twelve lines, rated.
Each line shows its rating and the reason for it; open a line for what to watch for and the controls that matter. Ratings are UrbanStat’s own editorial view of a typical business of this type, on a five-step scale. They are a starting point for questions, not a quote, a rate or a statistical measure.
Property
HighMolten metal meets water, oil or combustibles easily; induction furnace run-outs and hydraulic fires on die-casting machines are regular causes.
Fire, explosion, water and weather damage to buildings, contents and stock.
- Furnace linings run past their wear limit
- Mineral hydraulic oil on die-casting machines
- Wooden patterns and flammable core binders stored near pouring
- Lining wear monitoring, ground-leak detection and dry run-out pits
- Fire-resistant hydraulic fluid and sprinklers over die-casting cells
- Separate, protected pattern store and core room
Business interruption
HighFurnaces, molding lines and customers' patterns are hard to replace, and castings are often single-sourced for assembly plants.
How long and how costly a shutdown is.
- Just-in-time supply to vehicle or equipment assembly lines
- One melting furnace or one automatic molding line
- Patterns and dies with no duplicates or drawings
- Spare furnace coils, power supplies and linings on hand
- Pattern and die register with digital models held off site
- Agreed backup foundry for key parts
Premises liability
ModerateVisitors are few, but smoke, odor and noise bring complaints where housing has grown up around an old plant.
Injuries to customers and the public, on site or caused by operations elsewhere.
- Residential neighbors close to melting or shakeout stacks
- Artists or hobby groups allowed to pour
- Fume capture at melting, pouring and shakeout
- Visitor rules that keep outsiders behind barriers during pours
Products and completed work
ElevatedCastings become brake parts, valves, pump bodies and structural fittings; hidden porosity or wrong chemistry causes failures downstream.
Harm caused by what the business sells, serves, makes, installs or repairs.
- Safety-critical vehicle, rail, aircraft or pressure-containing castings
- Brass or bronze for drinking water fittings
- Contracts accepting recall and line-stoppage costs
- Spectrometer check on every melt with heat numbers cast in
- Radiographic or other non-destructive testing where specified
- Contract review limiting consequential damages
Workers’ injury
SevereAmong the most injurious manufacturing settings: metal splash burns, silica and metal fume, heat, noise, vibration and heavy lifting together.
Injuries and illness to employees.
- Wet, oily or sealed scrap charged into the furnace
- Manual pouring from hand ladles
- Grinding and chipping castings with hand tools all shift
- Charge preheating or drying and full molten-metal protective clothing
- Mechanized pouring, shakeout and casting handling
- Dust extraction with silica monitoring and hearing and lung surveillance
Commercial auto
ModerateCastings ship by carrier or a small own fleet; loads are dense and heavy.
Owned, hired and employee-driven vehicles, deliveries, customers’ vehicles in care.
- Own trucks delivering to assembly plants on fixed schedules
- Load securing for bins of castings and driver record checks
Crime and theft
ModerateCopper-base ingot, scrap and finished brass or bronze castings are attractive; iron and steel are not.
Burglary, robbery, employee dishonesty, cash, payment and invoice fraud.
- Nonferrous ingot and returns stored in an unlocked yard
- Caged metal store with weigh-in and weigh-out records
Inland marine and equipment
ElevatedCustomers' patterns, core boxes and dies stay in the foundry for years and can be worth more than the building.
Property in transit, at job sites or in the insured’s care, and mobile equipment.
- No inventory or agreed values for customer-owned tooling
- Wooden patterns stored in an unsprinklered loft or shed
- Tooling register with owner, value and storage location
- Written terms on responsibility for patterns and dies
Environmental
HighSpent sand, slag, furnace dust and binder residues carry metals and phenols, and stacks emit fume and odor.
Pollution on or from the site or the work.
- Decades of foundry sand used as fill on site
- Leaded brass or bronze melting
- Coke-fired cupola melting with limited emission control
- Baghouses and scrubbers maintained and stack tested
- Waste sand characterized and sent to licensed reuse or disposal
- Sealed, diked storage for binders, catalysts and oils
Cyber and data
ElevatedDie-casting cells, molding lines and melt controls are networked, and castings ship to tight schedules; ransomware stops pours and deliveries.
Data breaches, ransomware, system outages and attacks on connected equipment.
- Melt and molding controls reachable from office networks
- Customer portals and schedules with no offline fallback
- Segmented networks for furnaces, molding lines and die-casting cells
- Offline backups of recipes, pattern models and quality records
Professional liability
ModerateFoundries often advise on casting design, alloy and gating, and some sell simulation or engineering that customers rely on.
Loss or injury caused by advice, design, testing, care or another professional service.
- Casting design or alloy selection done for the customer
- Simulation or engineering services billed separately
- Customer approval of drawings, alloy and test requirements
- Written limits on liability for design assistance
Umbrella and excess
HighA cracked brake, steering or pressure casting can injure many people downstream, and a furnace explosion can hurt visitors and contractors.
How likely one liability event is to exhaust primary limits.
- Safety-critical castings for vehicles, rail or pressure systems
- Contractors relining furnaces or working near molten metal
- Traceable heat numbers and nondestructive testing on critical parts
- Contractors kept out of melt areas during pours
Construction, occupancy, protection, exposure.
What a risk engineer expects to find at a typical site of this type, and what to compare a submission against.
- Construction
- Older masonry or steel-frame high bays with crane runways, below-floor furnace and molding pits, timber pattern lofts, and additions built around original melt shops over decades.
- Occupancy
- Induction or cupola melting beside water-cooled coils, resin and oil core binders, hydraulic die-casting machines, wooden patterns, wax rooms and dewax autoclaves at investment foundries, grinding dust and magnesium or aluminum fines.
- Protection
- Dry run-out pits and ground-leak detection, sprinklers over die-casting cells, core rooms and pattern stores, explosion protection on dust collectors, and monitored alarms.
- Exposure
- Many old foundries sit in river valleys or older industrial districts where housing has grown close, with shared walls, neighbors' storage and odor complaints.
What to ask and look for.
Start with the desk review before quoting, then walk the site. Tick questions off as you go; ticks are kept in this browser only.
Before quoting: ask the broker or owner
Documents to request
On site: molding and finishing
On site: melting and fire protection
On site: people
On site: environment and records
Refer or decline if you find
- Past furnace run-out or explosion with no change in practice
- Wet scrap charged directly into molten metal
- Die-casting machines on mineral oil with no sprinklers
- Wooden pattern storage unsprinklered and unrecorded
- Waste sand piled or buried on site
How UrbanStat data helps.
Furnace pits and molding pits sit below floor level, so even shallow flooding puts water under molten metal. Older foundries in river valleys are common. Shaking and wind damage high bays, stacks and cranes.
- Flood scores at the address show whether water could reach furnace and molding pits, where shallow water under molten metal is an explosion hazard.
- Parcel and permit data give the construction date and permit history of plants that are often very old, including furnace, electrical and dust collector work.
- Street-by-street exposure views show the insured value concentrated at one foundry and the customers nearby that depend on it, with alerts at a set threshold.
What the published numbers say.
Official statistics for the industry or property type closest to this business. They describe the industry as a whole, not any one insured.
5.5 recordable injuries and illnesses per 100 full-time workers, above the private-industry average of 2.3.
1.5 of these cases per 100 workers involved days away from work.
United States, 2024. Industry: Iron foundries (NAICS 331511). Source: U.S. Bureau of Labor Statistics, Survey of Occupational Injuries and Illnesses, Table 1: incidence rates of nonfatal occupational injuries and illnesses by industry and case types, 2024.
6 fatal work injuries in 2024.
Deaths per 100,000 full-time equivalent workers, for the industry sector as a whole.
United States, private industry, 2024. Industry: Foundries (NAICS 3315), the closest published group. Source: U.S. Bureau of Labor Statistics, Census of Fatal Occupational Injuries; sector rates.
99 citations from 33 inspections; 70% were classed serious, willful or repeat.
- 1910.1053 Respirable crystalline silica20
- 1910.134 Respiratory protection11
- 1910.184 Slings6
- 1910.147 The control of hazardous energy (lockout/tagout)6
- 1910.1200 Hazard communication5
Standards cited most often in this industry, by number of citations.
United States, citations issued October 2024 to September 2025 (federal fiscal year 2025). Industry: Iron Foundries (NAICS 331511). Covers federal and state-plan inspections. A citation is one violation item; one inspection can produce several. Source: U.S. Department of Labor, Occupational Safety and Health Administration, OSHA enforcement data (inspections and violations); standard titles from the Code of Federal Regulations, Title 29 (section headings).
7,966 fires a year reported in industrial and manufacturing properties, causing about $810 million in direct property damage a year.
United States, 2020 to 2024, annual average. The group includes utility, defense, agriculture and mining properties. Source: National Fire Protection Association, Structure Fires in Industrial and Manufacturing Properties.
158 facilities reported toxic chemical releases totaling 15.3 million pounds on and off site.
- Zinc compounds7.9M
- Manganese and manganese compounds2.2M
- Manganese compounds1.5M
Chemicals released in the largest amounts, in pounds. 112 of the facilities reported at least one chemical classed as a carcinogen.
United States, 2024. Industry: Iron Foundries (NAICS 331511). Covers facilities in listed industries with ten or more full-time employees that handle listed chemicals above set thresholds. Source: U.S. Environmental Protection Agency, Toxics Release Inventory basic data files.
Industry loss ratios by line2020 to 2024, the same table on every guide
Loss ratios are published by line of insurance, not by business type. They show how each line has run for insurers as a whole, whatever the business insured.
| Published line | Closest line in this guide | 2020 | 2021 | 2022 | 2023 | 2024 |
|---|---|---|---|---|---|---|
| Fire | Property | 63.2% | 67.3% | 62.4% | 45.5% | 40.9% |
| Commercial multiple peril | Property and liability sold as a package | 61.2% | 60.2% | 59.4% | 61.2% | 54.4% |
| Inland marine | Inland marine and equipment | 64.5% | 49.4% | 47.1% | 44.1% | 44.0% |
| Other liability | Premises liability, and most umbrella, professional (other than medical) and cyber cover | 65.1% | 58.8% | 61.0% | 63.7% | 71.2% |
| Products liability | Products and completed work | 48.2% | 52.2% | 46.0% | 57.5% | 60.3% |
| Workers’ compensation | Workers’ injury | 47.9% | 49.2% | 45.0% | 44.3% | 46.0% |
| Commercial auto liability | Commercial auto | 68.3% | 66.5% | 71.9% | 76.8% | 77.6% |
| Commercial auto physical damage | Commercial auto | 50.9% | 56.3% | 64.3% | 65.1% | 57.9% |
United States. Losses incurred as a percent of direct premiums earned, countrywide, before reinsurance and not including loss adjustment expense. Source: National Association of Insurance Commissioners, Report on Profitability by Line by State in 2024, ten-year summary.
- Equipment breakdown
- Induction power supplies, furnace coils and die-casting machines fail without fire and stall every order behind them.
- Site pollution liability
- Spent sand used as fill, baghouse dust and binder residues leave metals and phenols in soil.
- Product recall
- Castings sit inside brakes, valves and pumps, so a defect can recall the customer's finished product.
- Contingent business interruption
- Foundries rely on a few suppliers of scrap, alloys, binders and power, and on large customers.
- Customers' tooling in care
- Patterns and dies owned by customers are often unvalued, unique and stored in combustible lofts.
NAICS and SIC codes for foundries
| System | Code | Industry |
|---|---|---|
| NAICS 2022, primary | 331511 | Iron Foundries |
| NAICS 2022 | 331523 | Nonferrous Metal Die-Casting Foundries |
| NAICS 2022 | 331524 | Aluminum Foundries (except Die-Casting) |
| NAICS 2022 | 331513 | Steel Foundries (except Investment) |
| NAICS 2022 | 331529 | Other Nonferrous Metal Foundries (except Die-Casting) |
| NAICS 2022 | 331512 | Steel Investment Foundries |
| SIC 1987, primary | 3321 | Gray and Ductile Iron Foundries |
| SIC 1987 | 3363 | Aluminum Die-Castings |
| SIC 1987 | 3365 | Aluminum Foundries |
| SIC 1987 | 3325 | Steel Foundries, NEC |
See this risk on the map.
Book a 30-minute walkthrough tailored to your portfolio and perils of interest.