Forging and powder metal parts manufacturersNAICS 332111 · SIC 3462
Forging shops heat steel, aluminum, titanium or nickel alloy billets and shape them under hammers and presses, while powder metal plants press metal powders into parts and sinter them in furnaces. Hydraulic oil, quench tanks, furnace gas and combustible dust meet heavy machinery making safety-critical parts.
NAICS 332111 Iron and Steel ForgingSIC 3462 Iron and Steel ForgingsNAICS 332112 Nonferrous ForgingNAICS 332117 Powder Metallurgy Part Manufacturing+2 more codes
Where losses come from.
- 01
Hydraulic oil sprayed onto hot dies and billets, starting fast-spreading press and pit fires
- 02
Crushing, burns, hearing loss and struck-by injuries around hammers, presses and manipulators
- 03
Hidden defects in crankshafts, landing gear, gears and fittings that fail in service
- PropertyProperty: High, 4 of 5; sector average 3.7; all business types 2.9.
- Business interruptionBusiness interruption: High, 4 of 5; sector average 3.5; all business types 2.7.
- Premises liabilityPremises liability: Moderate, 2 of 5; sector average 1.9; all business types 2.7.
- Products and completed workProducts and completed work: High, 4 of 5; sector average 3.4; all business types 2.6.
- Workers’ injuryWorkers’ injury: High, 4 of 5; sector average 3.4; all business types 3.0.
- Commercial autoCommercial auto: Moderate, 2 of 5; sector average 2.3; all business types 2.5.
- Crime and theftCrime and theft: Moderate, 2 of 5; sector average 1.9; all business types 2.2.
- Inland marine and equipmentInland marine and equipment: Elevated, 3 of 5; sector average 2.6; all business types 2.6.
- EnvironmentalEnvironmental: Elevated, 3 of 5; sector average 2.8; all business types 2.3.
- Cyber and dataCyber and data: Elevated, 3 of 5; sector average 2.7; all business types 2.7.
- Professional liabilityProfessional liability: Moderate, 2 of 5; sector average 1.5; all business types 2.0.
- Umbrella and excessUmbrella and excess: High, 4 of 5; sector average 3.6; all business types 3.6.
- Vehicle electrification cuts demand for engine and transmission forgings while adding parts for motors, chassis and battery structures, changing product mix and customer concentration.
- Additive manufacturing and metal injection molding bring finer, more reactive powders into plants, raising dust explosion and fire risk beyond traditional pressed parts.
- Servo presses, robots and induction heating are replacing manual hammer work, cutting burns and crush injuries but making production more dependent on software and controls.
Twelve lines, rated.
Each line shows its rating and the reason for it; open a line for what to watch for and the controls that matter. Ratings are UrbanStat’s own editorial view of a typical business of this type, on a five-step scale. They are a starting point for questions, not a quote, a rate or a statistical measure.
Property
HighLarge hydraulic presses leak oil onto hot work, quench tanks and sintering atmospheres can ignite, and fine metal powder explodes.
Fire, explosion, water and weather damage to buildings, contents and stock.
- Presses on mineral hydraulic oil with pits and basements below
- Oil-based die lubricants pooled on floors and in trenches
- Titanium, aluminum or magnesium fines in dust collectors
- Fire-resistant hydraulic fluid and sprinklers or foam in press pits
- Purge interlocks and flame curtains on sintering and atmosphere furnaces
- Wet or explosion-vented dust collection, with metal fines cleaned up daily
Business interruption
HighBig hammers and presses take many months to replace, dies are unique, and customer part approvals stay with this plant.
How long and how costly a shutdown is.
- One large press or hammer producing most of the revenue
- Aerospace or vehicle parts needing lengthy requalification elsewhere
- Dies with no spare set or digital model
- Spare hydraulic pumps, motors, columns and die blocks on hand
- Digital die models stored off site for quick re-sinking
- Agreements with other forges for overflow or emergency work
Premises liability
ModerateFew visitors come on site, but heavy hammers shake nearby buildings and the noise draws complaints from neighbors.
Injuries to customers and the public, on site or caused by operations elsewhere.
- Homes or offices built close to hammer shops
- Customers' inspectors walking the forge floor
- Vibration isolation under hammer foundations
- Escorted visits with hearing and eye protection
Products and completed work
HighForgings and sintered parts carry loads in engines, brakes, steering, aircraft and lifting gear; a lap, crack or porosity fails catastrophically.
Harm caused by what the business sells, serves, makes, installs or repairs.
- Aircraft, medical or lifting parts in the product mix
- Customer specifications requiring ultrasonic or magnetic testing of every piece
- Contracts accepting recall, field campaign or line-stoppage costs
- Heat lot traceability from billet to shipped part
- Nondestructive testing and destructive sampling matched to part criticality
- Contract review capping consequential damages and requiring customer validation
Workers’ injury
HighWorkers feed hot billets to hammers and presses, facing burns, crushing, flying scale, extreme noise, heat stress and heavy lifting.
Injuries and illness to employees.
- Manual tong handling of hot stock at hammers
- Die changes without blocking or lockout
- Powder handling without dust control or respirators
- Manipulators and robots for loading and transfer of hot stock
- Hearing conservation with audiometric testing and enclosed operator cabs
- Lockout and die blocks required for every die change
Commercial auto
ModerateParts usually ship by carrier; some shops run trucks to heat treaters, machinists and nearby customers.
Owned, hired and employee-driven vehicles, deliveries, customers’ vehicles in care.
- Own trucks hauling heavy bins of forgings on tight delivery windows
- Driver record checks and load securing for dense steel loads
Crime and theft
ModerateTitanium, nickel alloy and copper bar and their scrap turnings sell well; carbon steel parts have little resale value.
Burglary, robbery, employee dishonesty, cash, payment and invoice fraud.
- Titanium or nickel alloy scrap stored in an open yard
- Locked scrap bins with weights recorded and reconciled to purchases
Inland marine and equipment
ElevatedCustomers' dies and tooling stay in the plant for years, and parts travel out for heat treating, machining and testing.
Property in transit, at job sites or in the insured’s care, and mobile equipment.
- No register or agreed values for customer-owned dies
- Work in progress held at outside processors for weeks
- Die list showing each owner, agreed value and rack position
- Signed terms on who bears loss of dies and parts away from the plant
Environmental
ElevatedGraphite die lubricants, hydraulic and quench oils, pickling acids and injection molding binders contaminate soil and drains if unmanaged.
Pollution on or from the site or the work.
- Oil-soaked floors and trenches draining to the ground
- Old pickling tanks or solvent degreasers on site
- Lined trenches and oil separators on all floor drains
- Diked storage and licensed disposal for spent oils and acids
Cyber and data
ElevatedNetworked presses and induction heaters drive production, and defense and aerospace work brings controlled drawings that customers expect protected.
Data breaches, ransomware, system outages and attacks on connected equipment.
- Customer drawings shared by email or unsecured file transfer
- Press controls reachable remotely by equipment makers
- Segmented production network and controlled vendor access
- Access controls and logging on customer technical data
Professional liability
ModerateMany shops help customers convert machined or cast parts to forged or powder metal designs, and a weak redesign leads to claims.
Loss or injury caused by advice, design, testing, care or another professional service.
- Design or material changes proposed by the shop's engineers
- Customer approval in writing for every design change
Umbrella and excess
HighOne defective forging in an aircraft, vehicle steering system or lifting hook can cause deaths and claims across a whole production run.
How likely one liability event is to exhaust primary limits.
- Aerospace, rail or lifting gear customers
- Long production runs shipped before test results return
- Shipments held until test results are approved
- Batch segregation that limits recalls to known heat lots
Construction, occupancy, protection, exposure.
What a risk engineer expects to find at a typical site of this type, and what to compare a submission against.
- Construction
- Older steel-frame forge halls with heavy crane runways, deep hammer foundations, press pits and basements holding hydraulic power units, often with later additions for heat treating and machining.
- Occupancy
- Gas and induction heating of billets, oil-based die lubricants, high-pressure hydraulics beside red-hot work, oil quench tanks, sintering furnaces with flammable atmospheres and fine metal powders.
- Protection
- Sprinklers throughout with foam or deluge in press pits, fire-resistant hydraulic fluids, furnace purge interlocks, explosion-vented dust collectors and automatic shut-off of hydraulic pumps.
- Exposure
- Usually in older industrial districts beside machine shops and heat treaters; hammer vibration and noise reach neighbors, and housing has often grown up close to the plant.
What to ask and look for.
Start with the desk review before quoting, then walk the site. Tick questions off as you go; ticks are kept in this browser only.
Before quoting: ask the broker or owner
Documents to request
On site: forge floor
On site: fire and explosion
On site: quality and people
Refer or decline if you find
- Presses on mineral oil above unprotected pits or basements
- Metal powder or fines accumulated on beams and ledges
- Sintering furnaces with bypassed purge or flame safety interlocks
- Safety-critical parts shipped without traceability to heat lot
- Manual tong work at heavy hammers with no guarding
How UrbanStat data helps.
Press pits and hydraulic basements sit below grade, so even shallow flooding reaches the costliest machinery first. Tall forge halls with crane runways take damage from tornadoes, wind and earthquakes.
- Flood scores at the address show whether press pits and hydraulic basements, where the costliest machinery sits, lie in water's path.
- Parcel and permit data give the age of older forge halls and recent electrical, furnace and sprinkler permits, a quick check on upgrades since the last survey.
- Street-by-street exposure views show insured value concentrated where forges, heat treaters and machine shops cluster in one industrial district, with alerts when a threshold is passed.
What the published numbers say.
Official statistics for the industry or property type closest to this business. They describe the industry as a whole, not any one insured.
5.4 recordable injuries and illnesses per 100 full-time workers, above the private-industry average of 2.3.
1.7 of these cases per 100 workers involved days away from work.
United States, 2024. Industry: Iron and steel forging (NAICS 332111). Source: U.S. Bureau of Labor Statistics, Survey of Occupational Injuries and Illnesses, Table 1: incidence rates of nonfatal occupational injuries and illnesses by industry and case types, 2024.
5 fatal work injuries in 2024, most often from falls, slips and trips (3).
Deaths per 100,000 full-time equivalent workers, for the industry sector as a whole.
United States, private industry, 2024. Industry: Forging and Stamping (NAICS 33211), the closest published group. Source: U.S. Bureau of Labor Statistics, Census of Fatal Occupational Injuries; sector rates.
96 citations from 30 inspections; 61% were classed serious, willful or repeat.
- 1910.212 General requirements for all machines8
- 1910.1200 Hazard communication8
- 1910.134 Respiratory protection6
- 1910.1053 Respirable crystalline silica6
- 1910.147 The control of hazardous energy (lockout/tagout)5
Standards cited most often in this industry, by number of citations.
United States, citations issued October 2024 to September 2025 (federal fiscal year 2025). Industry: Iron and Steel Forging (NAICS 332111). Covers federal and state-plan inspections. A citation is one violation item; one inspection can produce several. Source: U.S. Department of Labor, Occupational Safety and Health Administration, OSHA enforcement data (inspections and violations); standard titles from the Code of Federal Regulations, Title 29 (section headings).
7,966 fires a year reported in industrial and manufacturing properties, causing about $810 million in direct property damage a year.
United States, 2020 to 2024, annual average. The group includes utility, defense, agriculture and mining properties. Source: National Fire Protection Association, Structure Fires in Industrial and Manufacturing Properties.
84 facilities reported toxic chemical releases totaling 348,188 pounds on and off site.
- Nickel130,974
- Chromium72,465
- Manganese62,310
Chemicals released in the largest amounts, in pounds. 70 of the facilities reported at least one chemical classed as a carcinogen.
United States, 2024. Industry: Iron and Steel Forging (NAICS 332111). Covers facilities in listed industries with ten or more full-time employees that handle listed chemicals above set thresholds. Source: U.S. Environmental Protection Agency, Toxics Release Inventory basic data files.
Industry loss ratios by line2020 to 2024, the same table on every guide
Loss ratios are published by line of insurance, not by business type. They show how each line has run for insurers as a whole, whatever the business insured.
| Published line | Closest line in this guide | 2020 | 2021 | 2022 | 2023 | 2024 |
|---|---|---|---|---|---|---|
| Fire | Property | 63.2% | 67.3% | 62.4% | 45.5% | 40.9% |
| Commercial multiple peril | Property and liability sold as a package | 61.2% | 60.2% | 59.4% | 61.2% | 54.4% |
| Inland marine | Inland marine and equipment | 64.5% | 49.4% | 47.1% | 44.1% | 44.0% |
| Other liability | Premises liability, and most umbrella, professional (other than medical) and cyber cover | 65.1% | 58.8% | 61.0% | 63.7% | 71.2% |
| Products liability | Products and completed work | 48.2% | 52.2% | 46.0% | 57.5% | 60.3% |
| Workers’ compensation | Workers’ injury | 47.9% | 49.2% | 45.0% | 44.3% | 46.0% |
| Commercial auto liability | Commercial auto | 68.3% | 66.5% | 71.9% | 76.8% | 77.6% |
| Commercial auto physical damage | Commercial auto | 50.9% | 56.3% | 64.3% | 65.1% | 57.9% |
United States. Losses incurred as a percent of direct premiums earned, countrywide, before reinsurance and not including loss adjustment expense. Source: National Association of Insurance Commissioners, Report on Profitability by Line by State in 2024, ten-year summary.
- Product recall
- Forged and sintered parts go into vehicles and machines in large runs; one defect can recall them all.
- Aircraft products liability
- Parts sold into aircraft are usually excluded from general liability and need specific products cover.
- Equipment breakdown
- Press hydraulics, crankshafts, clutches and induction power supplies fail without fire and take months to rebuild.
- Customers' tooling in care
- Customer-owned dies held for years can be worth more than the plant's own machinery.
NAICS and SIC codes for forging and powder metal parts manufacturers
See this risk on the map.
Book a 30-minute walkthrough tailored to your portfolio and perils of interest.