Aluminum producers and millsNAICS 331313 · SIC 3334

Aluminum producers refine bauxite into alumina, smelt it in electrolytic potlines, or remelt scrap, then cast ingot, slab and billet for rolling into sheet, plate and foil or pressing into extrusions. Molten metal near water, flammable rolling oils, fine aluminum dust and total dependence on electricity drive the largest losses.

NAICS 331313 Alumina Refining and Primary Aluminum ProductionSIC 3334 Primary Production of AluminumNAICS 331314 Secondary Smelting and Alloying of AluminumNAICS 331315 Aluminum Sheet, Plate, and Foil Manufacturing+4 more codes

Manufacturing · Updated November 2026

01 / Loss drivers

Where losses come from.

  1. 01

    Molten aluminum meeting water in casting pits, wet scrap or dross, causing violent explosions

  2. 02

    Fires in cold rolling mills, hydraulic cellars and oil-laden exhaust ducts, and aluminum dust explosions

  3. 03

    Long shutdowns when power outages freeze potlines or transformers, rectifiers or mill drives fail

How it comparesEach line’s rating against the average for its NAICS sector, Manufacturing (178 business types), and for all 747.
  1. PropertyProperty: High, 4 of 5; sector average 3.7; all business types 2.9.
  2. Business interruptionBusiness interruption: Severe, 5 of 5; sector average 3.5; all business types 2.7.
  3. Premises liabilityPremises liability: Moderate, 2 of 5; sector average 1.9; all business types 2.7.
  4. Products and completed workProducts and completed work: Elevated, 3 of 5; sector average 3.4; all business types 2.6.
  5. Workers’ injuryWorkers’ injury: High, 4 of 5; sector average 3.4; all business types 3.0.
  6. Commercial autoCommercial auto: Elevated, 3 of 5; sector average 2.3; all business types 2.5.
  7. Crime and theftCrime and theft: Elevated, 3 of 5; sector average 1.9; all business types 2.2.
  8. Inland marine and equipmentInland marine and equipment: Elevated, 3 of 5; sector average 2.6; all business types 2.6.
  9. EnvironmentalEnvironmental: High, 4 of 5; sector average 2.8; all business types 2.3.
  10. Cyber and dataCyber and data: Elevated, 3 of 5; sector average 2.7; all business types 2.7.
  11. Professional liabilityProfessional liability: Low, 1 of 5; sector average 1.5; all business types 2.0.
  12. Umbrella and excessUmbrella and excess: High, 4 of 5; sector average 3.6; all business types 3.6.
What’s changing
  • Vehicle makers are moving body panels, crash structures and battery enclosures to aluminum, raising volumes of safety-critical sheet and extrusions and the product exposure attached.
  • Remelting more mixed post-consumer scrap brings coatings, plastics, hidden lithium batteries and moisture into furnaces, raising explosion, fire and emissions risk.
  • Smelters increasingly run on wind, solar and hydro contracts and sell demand flexibility to the grid, so planned and unplanned potline power cuts need tight control.
02 / Line by line

Twelve lines, rated.

Each line shows its rating and the reason for it; open a line for what to watch for and the controls that matter. Ratings are UrbanStat’s own editorial view of a typical business of this type, on a five-step scale. They are a starting point for questions, not a quote, a rate or a statistical measure.

Property

High
Molten metal meets cooling water at every casting pit, cold mills spray flammable oil, and fine aluminum dust burns or explodes.

Fire, explosion, water and weather damage to buildings, contents and stock.

Watch for
  • Casting pits with worn coatings or no water-flow interlocks
  • Cold and foil mills relying on hand extinguishers alone
  • Remelting of mixed, painted or oily scrap without drying
Controls that matter
  • Dry-pit design, pit coatings and interlocks that stop casting on cooling faults
  • Fixed carbon dioxide or water-mist systems on mill stands and exhaust ducts
  • Scrap dried or preheated, with sealed containers removed before charging

Business interruption

Severe
Potlines freeze if power fails for a few hours, and restarting cells or replacing a hot mill drive takes many months.

How long and how costly a shutdown is.

Watch for
  • A single transmission line or substation feeding the potlines
  • One hot mill, one caster or one large extrusion press
  • Customers with long qualification times for aerospace or vehicle sheet
Controls that matter
  • Two independent power feeds and a rehearsed procedure for keeping cells alive
  • Spare rectifier transformers, mill motors and press cylinders held on site
  • Agreements to buy slab or billet from other producers during an outage

Premises liability

Moderate
Plants sit behind fences away from the public; exposure comes from contractors, carriers and emissions reaching neighbors.

Injuries to customers and the public, on site or caused by operations elsewhere.

Watch for
  • Large numbers of contractors during potline relines and mill rebuilds
  • Fluoride or odor complaints from nearby farms and housing
Controls that matter
  • Contractor prequalification, site induction and permit-to-work for hot work and entry
  • Indemnity and insurance requirements written into every service contract

Products and completed work

Elevated
Sheet, plate and extrusions go into aircraft, vehicles, cans and building facades; wrong alloy or temper causes failures far downstream.

Harm caused by what the business sells, serves, makes, installs or repairs.

Watch for
  • Aerospace plate, vehicle crash structures or pressure cylinders in the product mix
  • Facade panels and window systems with fire or structural requirements
  • Contracts accepting the customer's recall and line-stoppage costs
Controls that matter
  • Chemistry and mechanical tests on every lot, traceable to cast number
  • Ultrasonic inspection of plate sold for aerospace or pressure use
  • Contract review that caps consequential damages

Workers’ injury

High
Molten metal splash, heat stress, caustic burns, potroom fume and coil handling cause serious injuries and occupational disease.

Injuries and illness to employees.

Watch for
  • Manual tapping, skimming and dross handling close to open metal
  • Workers on foot near mill coils, cranes and moving billets
  • Older anode technology releasing tar fumes in the potroom
Controls that matter
  • Aluminized protective clothing and exclusion zones during tapping and casting
  • Fume capture on cells, with fluoride and tar exposure monitoring
  • Machine guarding and lockout on mill stands, saws and presses

Commercial auto

Elevated
Coil, ingot and billet ship by heavy truck, and some plants deliver liquid aluminum in crucibles to nearby die-casters.

Owned, hired and employee-driven vehicles, deliveries, customers’ vehicles in care.

Watch for
  • Own trucks carrying molten metal crucibles on public roads
  • Heavy coils badly secured on flatbeds
Controls that matter
  • Crucible design, route planning and trained drivers for hot metal deliveries
  • Coil securing rules checked at the gate before release

Crime and theft

Elevated
Ingot, coil and clean scrap sell easily, cargo thieves target loaded trailers, and bought-in scrap brings short weights and misgraded loads.

Burglary, robbery, employee dishonesty, cash, payment and invoice fraud.

Watch for
  • Loaded trailers parked overnight outside the fence
  • Scrap weighed, graded and paid by the same employee
Controls that matter
  • Fenced, lit and camera-covered trailer yards with gate checks
  • Separate weighing, grading and payment duties with regular audits

Inland marine and equipment

Elevated
Bauxite, alumina and finished coil move by ship, barge and rail, and plants run costly tapping vehicles and mobile equipment.

Property in transit, at job sites or in the insured’s care, and mobile equipment.

Watch for
  • Stock held at ports, outside processors or customers' sites
  • Mobile equipment working beside molten metal and hot dross
Controls that matter
  • Shipments and stock at ports or processors scheduled with values by location
  • Fire suppression and heat shielding on mobile plant in hot areas

Environmental

High
Spent potliner, salt cake, dross, red mud, fluoride emissions and rolling oils leave long-lasting soil and water contamination.

Pollution on or from the site or the work.

Watch for
  • Spent potliner or salt cake stored uncovered outdoors
  • Red mud or process water held in large earthen impoundments
  • Long industrial history and old landfills on the property
Controls that matter
  • Covered, lined storage and licensed treatment for spent potliner and dross
  • Dry scrubbers on potlines and baghouses on remelt furnaces
  • Impoundment inspections, groundwater monitoring and diked oil storage

Cyber and data

Elevated
Potline control, casting and mill automation run on networked systems; ransomware can force manual operation and stop shipments.

Data breaches, ransomware, system outages and attacks on connected equipment.

Watch for
  • Process control networks reachable from office systems or remote vendors
  • Unsupported control software that cannot be patched
Controls that matter
  • Segmented plant networks with controlled vendor remote access
  • Offline backups and drilled manual operation of potlines and casting

Professional liability

Low
Little advice is sold; alloy and temper recommendations are treated as part of the product sale.

Loss or injury caused by advice, design, testing, care or another professional service.

Watch for
  • Metallurgical consulting or testing sold to outside clients
Controls that matter
  • Written terms limiting liability for technical advice given to customers

Umbrella and excess

High
A casting pit explosion during a shutdown, a molten metal truck crash or an impoundment failure can injure many people.

How likely one liability event is to exhaust primary limits.

Watch for
  • Major shutdowns with many contractors near metal and cranes
  • Impoundments close to homes or waterways
Controls that matter
  • Contractors kept out of casting areas while metal is poured
  • Regular impoundment inspections by qualified engineers
03 / Property picture

Construction, occupancy, protection, exposure.

What a risk engineer expects to find at a typical site of this type, and what to compare a submission against.

Construction
Very large steel-frame halls with crane rails, long potrooms, below-grade casting pits and oil cellars, and older roofs with combustible insulation or plastic skylights.
Occupancy
Molten metal held beside water-cooled casting, kerosene-type rolling oils sprayed at speed, hydraulic extrusion presses, anode baking furnaces driving off pitch fumes, and fine dust from sawing, scalping and powder making.
Protection
Fixed suppression on mill stands and exhaust, sprinklered cellars and oil rooms, interlocked casting systems, dust collectors with explosion venting, and a trained on-site emergency team.
Exposure
Often isolated beside ports, rivers or dedicated power plants and fed by long transmission lines; red mud lakes, scrap yards and other heavy industry may sit next door.
04 / Checklist

What to ask and look for.

Start with the desk review before quoting, then walk the site. Tick questions off as you go; ticks are kept in this browser only.

Before quoting: ask the broker or owner

Documents to request

On site: melting and casting

On site: mills and fire protection

On site: power and continuity

On site: people and environment

Refer or decline if you find

  • Wet or sealed scrap charged without drying, inspection or preheating
  • Casting pits without coatings, dry design or cooling water interlocks
  • Cold rolling mills without fixed suppression on stands and exhaust ducts
  • Aluminum fines or dust building up on beams and ledges
  • Single power feed to potlines with no tested outage response
05 / Location

How UrbanStat data helps.

Plants sit by ports and rivers for bauxite and cooling water, so floodwater reaching casting pits becomes an explosion hazard. Wildfire, hurricane or quake damage to transmission lines can cut power and freeze potlines.

FloodStorm surgeHurricaneEarthquakeWildfire
  • Address-level flood and storm surge scores indicate whether rising water could get into casting pits, oil cellars and rectifier yards at portside smelters and mills.
  • Live hurricane tracks and wildfire perimeters show which insured smelters and mills lie in an event's path, while there is still time for a controlled shutdown.
  • Parcel and building-permit data give the construction date and recent permits for cast houses and mill halls, a quick check on furnace, roof and electrical work.
Flood · Storm surge · Hurricane · Earthquake
06 / Public loss data · NAICS 331313

What the published numbers say.

Official statistics for the industry or property type closest to this business. They describe the industry as a whole, not any one insured.

Workers’ injury frequency

2.1 recordable injuries and illnesses per 100 full-time workers, close to the private-industry average of 2.3.

Alumina refining and primary aluminum production
2.1
All private industry
2.3

0.6 of these cases per 100 workers involved days away from work.

United States, 2024. Industry: Alumina refining and primary aluminum production (NAICS 331313). Source: U.S. Bureau of Labor Statistics, Survey of Occupational Injuries and Illnesses, Table 1: incidence rates of nonfatal occupational injuries and illnesses by industry and case types, 2024.

Workplace deaths

15 fatal work injuries in 2024, most often from contact with objects and equipment (6).

Manufacturing
2.4
All workers
3.3

Deaths per 100,000 full-time equivalent workers, for the industry sector as a whole.

United States, private industry, 2024. Industry: Primary Metal Manufacturing (NAICS 331), the closest published group. Source: U.S. Bureau of Labor Statistics, Census of Fatal Occupational Injuries; sector rates.

Most cited safety standards

74 citations from 13 inspections; 45% were classed serious, willful or repeat.

  • 1910.146 Permit-required confined spaces
    10
  • 1910.179 Overhead and gantry cranes
    4
  • 1910.1200 Hazard communication
    4
  • 1910.132 General requirements (personal protective equipment)
    4
  • 1910.157 Portable fire extinguishers
    4

Standards cited most often in this industry, by number of citations.

United States, citations issued October 2024 to September 2025 (federal fiscal year 2025). Industry: Alumina Refining and Primary Aluminum Production (NAICS 331313). Covers federal and state-plan inspections. A citation is one violation item; one inspection can produce several. Source: U.S. Department of Labor, Occupational Safety and Health Administration, OSHA enforcement data (inspections and violations); standard titles from the Code of Federal Regulations, Title 29 (section headings).

Fire frequency

7,966 fires a year reported in industrial and manufacturing properties, causing about $810 million in direct property damage a year.

United States, 2020 to 2024, annual average. The group includes utility, defense, agriculture and mining properties. Source: National Fire Protection Association, Structure Fires in Industrial and Manufacturing Properties.

Toxic chemical releases

10 facilities reported toxic chemical releases totaling 4.5 million pounds on and off site.

  • Carbonyl sulfide
    1.8M
  • Sulfuric acid
    868,654
  • Zinc compounds
    637,295

Chemicals released in the largest amounts, in pounds. 8 of the facilities reported at least one chemical classed as a carcinogen.

United States, 2024. Industry: Alumina Refining and Primary Aluminum Production (NAICS 331313). Covers facilities in listed industries with ten or more full-time employees that handle listed chemicals above set thresholds. Source: U.S. Environmental Protection Agency, Toxics Release Inventory basic data files.

Industry loss ratios by line2020 to 2024, the same table on every guide

Loss ratios are published by line of insurance, not by business type. They show how each line has run for insurers as a whole, whatever the business insured.

Published lineClosest line in this guide20202021202220232024
FireProperty63.2%67.3%62.4%45.5%40.9%
Commercial multiple perilProperty and liability sold as a package61.2%60.2%59.4%61.2%54.4%
Inland marineInland marine and equipment64.5%49.4%47.1%44.1%44.0%
Other liabilityPremises liability, and most umbrella, professional (other than medical) and cyber cover65.1%58.8%61.0%63.7%71.2%
Products liabilityProducts and completed work48.2%52.2%46.0%57.5%60.3%
Workers’ compensationWorkers’ injury47.9%49.2%45.0%44.3%46.0%
Commercial auto liabilityCommercial auto68.3%66.5%71.9%76.8%77.6%
Commercial auto physical damageCommercial auto50.9%56.3%64.3%65.1%57.9%

United States. Losses incurred as a percent of direct premiums earned, countrywide, before reinsurance and not including loss adjustment expense. Source: National Association of Insurance Commissioners, Report on Profitability by Line by State in 2024, ten-year summary.

Coverages to raise
Equipment breakdown
Rectifiers, furnace transformers, mill drives and extrusion press cylinders fail without fire and take months to replace.
Utility service interruption
A power cut of a few hours off the premises can freeze potlines, so outside power failure needs cover.
Contingent business interruption
Plants depend on few suppliers of alumina, anodes and power, and on a handful of large customers.
Product recall
Sheet and extrusions go into vehicles, aircraft and packaging, where one alloy defect recalls finished goods.
Ocean and inland cargo
Bauxite, alumina and coil travel by ship, barge and rail, often at the producer's risk.

NAICS and SIC codes for aluminum producers and mills

SystemCodeIndustry
NAICS 2022, primary331313Alumina Refining and Primary Aluminum Production
NAICS 2022331314Secondary Smelting and Alloying of Aluminum
NAICS 2022331315Aluminum Sheet, Plate, and Foil Manufacturing
NAICS 2022331318Other Aluminum Rolling, Drawing, and Extruding
SIC 1987, primary3334Primary Production of Aluminum
SIC 19873341Secondary Smelting and Refining of Nonferrous Metals
SIC 19873353Aluminum Sheet, Plate, and Foil
SIC 19873354Aluminum Extruded Products
Next step

See this risk on the map.

Book a 30-minute walkthrough tailored to your portfolio and perils of interest.

Request a Demo →