Plastics molders and extruders

Plastics processors compound or melt resin pellets and shape them by injection, blow or rotational molding, extrusion, thermoforming, laminating or foaming into parts, bottles, bags, film, sheet, pipe and foam. Heat, hydraulic oil and large stocks of plastic make fire the leading loss, and customers' molds tie the plant into tight supply chains.

Manufacturing · NAICS 326199 · SIC 3089 · Updated November 2026

01 / Loss drivers

Where losses come from.

  1. 01

    Fires at presses and extruders fed by hydraulic oil, heater bands and stored plastic

  2. 02

    Crush, amputation and burn injuries at molding machines, granulators and during purging

  3. 03

    Loss of customers' molds and missed deliveries to just-in-time buyers

How it comparesEach line’s rating against the average for its NAICS sector, Manufacturing (178 business types), and for all 747.
  1. PropertyProperty: High, 4 of 5; sector average 3.7; all business types 2.9.
  2. Business interruptionBusiness interruption: High, 4 of 5; sector average 3.5; all business types 2.7.
  3. Premises liabilityPremises liability: Moderate, 2 of 5; sector average 1.9; all business types 2.7.
  4. Products and completed workProducts and completed work: Elevated, 3 of 5; sector average 3.4; all business types 2.6.
  5. Workers’ injuryWorkers’ injury: Elevated, 3 of 5; sector average 3.4; all business types 3.0.
  6. Commercial autoCommercial auto: Moderate, 2 of 5; sector average 2.3; all business types 2.5.
  7. Crime and theftCrime and theft: Low, 1 of 5; sector average 1.9; all business types 2.2.
  8. Inland marine and equipmentInland marine and equipment: Elevated, 3 of 5; sector average 2.6; all business types 2.6.
  9. EnvironmentalEnvironmental: Moderate, 2 of 5; sector average 2.8; all business types 2.3.
  10. Cyber and dataCyber and data: Elevated, 3 of 5; sector average 2.7; all business types 2.7.
  11. Professional liabilityProfessional liability: Moderate, 2 of 5; sector average 1.5; all business types 2.0.
  12. Umbrella and excessUmbrella and excess: Elevated, 3 of 5; sector average 3.6; all business types 3.6.
What’s changing
  • Rules on single-use plastics and recycled content push more post-consumer resin into products, bringing contamination, variable quality and baled scrap storage.
  • Electric vehicles shift molders toward battery housings and high-voltage connectors, parts where a failure can start a fire and lead to recalls.
  • Automated part removal and lights-out production cut reach-in injuries but leave presses and heaters running with nobody in the building.
02 / Line by line

Twelve lines, rated.

Each line shows its rating and the reason for it; open a line for what to watch for and the controls that matter. Ratings are UrbanStat’s own editorial view of a typical business of this type, on a five-step scale. They are a starting point for questions, not a quote, a rate or a statistical measure.

Property

High
Molten plastic, hot hydraulic oil and electrical heaters sit beside finished goods, cartons and foam that burn fast with heavy smoke.

Fire, explosion, water and weather damage to buildings, contents and stock.

Watch for
  • Expanded foam production using pentane or other flammable blowing agents
  • Finished goods and pallets stored between machines or to the roof
  • Hydraulic leaks, oil-soaked floors and aging heater wiring
Controls that matter
  • Sprinklers designed for plastics storage, including in-rack where needed
  • Fire-resistant hydraulic fluid or leak shut-offs on large presses
  • Thermographic checks of heater bands, panels and drives

Business interruption

High
Molds are unique, long-lead tools, presses are sized to the job, and automotive, medical and packaging buyers hold little buffer stock.

How long and how costly a shutdown is.

Watch for
  • Customer-owned molds with no duplicate or drawings
  • Sole supplier of a component to a vehicle or appliance line
  • One large press or extrusion line with no equivalent nearby
Controls that matter
  • Mold register with values, owners and fire-protected storage
  • Agreed transfer plan to sister plants or other molders
  • Finished goods buffer held in a separate building

Premises liability

Moderate
Trade customers and truck drivers are the only visitors, and little work is done away from the plant.

Injuries to customers and the public, on site or caused by operations elsewhere.

Watch for
  • Resin silos and loading docks close to public roads
Controls that matter
  • Driver safety rules and marked routes in the yard

Products and completed work

Elevated
Most output is components made to customers' designs, but pipe, food packaging, medical parts and vehicle parts carry real injury and recall potential.

Harm caused by what the business sells, serves, makes, installs or repairs.

Watch for
  • Pressure pipe, fittings or fuel and chemical containers
  • Medical device or food-contact parts needing certified resin
  • Regrind or recycled resin blended without controls
Controls that matter
  • Resin lot traceability from silo to shipped carton
  • Contracts placing design responsibility on the customer
  • Process monitoring and dimensional checks on every run

Workers’ injury

Elevated
Operators reach into mold areas, clear granulators and handle molten purge, with repetitive trimming and packing on every shift.

Injuries and illness to employees.

Watch for
  • Bypassed gate interlocks on molding machines
  • Mold changes done by crane without lockout
  • Temporary workers on machines after brief induction
Controls that matter
  • Interlocks tested each shift and lockout for mold changes
  • Face shields and sleeves for purging and hot runner work
  • Robots or conveyors removing parts in place of hand reach-in

Commercial auto

Moderate
Most output ships by carrier; some plants run shuttle trucks to nearby customers or warehouses.

Owned, hired and employee-driven vehicles, deliveries, customers’ vehicles in care.

Watch for
  • Own trucks making timed deliveries to assembly plants
Controls that matter
  • Driver qualification files and maintenance records for shuttle trucks

Crime and theft

Low
Resin and molded parts have limited resale value, and no cash is handled.

Burglary, robbery, employee dishonesty, cash, payment and invoice fraud.

Watch for
  • Truckload resin purchases paid against altered bank details
Controls that matter
  • Verification calls before changing supplier payment details

Inland marine and equipment

Elevated
Customers' molds and tooling in the plant are often worth more than the molder's own machines, and travel for repair.

Property in transit, at job sites or in the insured’s care, and mobile equipment.

Watch for
  • Molds of others not listed, valued or insured by anyone
  • Tools shipped to outside toolrooms for repair
Controls that matter
  • Written agreement on who insures each mold, at what value
  • Transit cover for molds moving to and from tool shops

Environmental

Moderate
Processing is largely clean; hydraulic oil, cooling water, pellet spills and styrene or blowing-agent emissions are the issues.

Pollution on or from the site or the work.

Watch for
  • Pellets escaping to storm drains from silo unloading
  • Polyurethane foam lines storing isocyanates in bulk
Controls that matter
  • Drain screens and sweep-up routine at resin unloading points
  • Secondary containment for hydraulic oil and foam chemicals

Cyber and data

Elevated
Presses, extrusion lines and robots run on networked controls, and automotive and packaging buyers place just-in-time orders through electronic links.

Data breaches, ransomware, system outages and attacks on connected equipment.

Watch for
  • Press and robot controllers reachable from the office network
  • Remote access for machine builders left permanently open
Controls that matter
  • Separate plant networks with logged, time-limited vendor access
  • Offline backups of process settings, mold data and orders

Professional liability

Moderate
Many molders help design parts and choose resins, and that design or material choice gets blamed when parts crack or fail.

Loss or injury caused by advice, design, testing, care or another professional service.

Watch for
  • Part design, mold flow analysis or resin selection offered as a service
Controls that matter
  • Design work under signed agreements that leave final approval with the customer

Umbrella and excess

Elevated
A cracked pressure pipe, a failed vehicle part or a large plant fire reaching neighbors can produce claims beyond primary limits.

How likely one liability event is to exhaust primary limits.

Watch for
  • Safety-critical vehicle parts, fuel tanks or medical components
  • Pressure pipe for gas or water service
Controls that matter
  • Supply contracts that cap liability and fix design responsibility
  • Lot traceability that limits a recall to the affected runs
03 / Property picture

Construction, occupancy, protection, exposure.

What a risk engineer expects to find at a typical site of this type, and what to compare a submission against.

Construction
Large single-story steel buildings with press halls, extrusion lines, outdoor resin silos and big warehouses; many have grown by additions with gaps in sprinkler coverage.
Occupancy
Molten plastic, heater bands and hydraulic oil at every machine, with cartons, pallets, foam and finished plastic goods stored close by and often to the roof.
Protection
Sprinklers designed for plastic storage at actual heights, fire-resistant hydraulic fluid on big presses, gas detection on foam lines using pentane, and regular thermographic scans.
Exposure
Industrial parks put molders beside their suppliers and customers; a plastics fire throws dense smoke over a wide area, and silos and trailers in the yard feed it.
04 / Checklist

What to ask and look for.

Start with the desk review before quoting, then walk the site. Tick questions off as you go; ticks are kept in this browser only.

Before quoting: ask the broker or owner

Documents to request

On site: products and processes

On site: premises and protection

On site: molds and continuity

On site: people and records

Refer or decline if you find

  • Foam production with flammable blowing agent and no gas detection
  • Plastic goods stored above the sprinkler design height
  • Bypassed safety gates on molding machines
  • High-value customer molds with no insurance agreement
  • Oil-soaked floors and pooled hydraulic fluid under presses
05 / Location

How UrbanStat data helps.

Wide metal-roofed plants lose roof coverings to wind and hail, and rain on molds and electrical cabinets does lasting damage. Power loss freezes resin in barrels and dies. Flood reaches press pits, chillers and ground-level tooling.

WindHailTornadoFlood
  • Wind, hail and tornado scores for the site inform roof terms where rain on molds, presses and control cabinets would stop production.
  • Flood scores at the address show whether press pits, chillers and ground-level mold storage sit in the water's path before interruption cover is priced.
  • Street-by-street exposure views reveal when a molder and the customers or suppliers it depends on share one industrial park, with alerts at a set threshold.
Wind · Hail · Tornado · Flood
06 / Public loss data

What the published numbers say.

Official statistics for the industry or property type closest to this business. They describe the industry as a whole, not any one insured.

Workers’ injury frequency

2.8 recordable injuries and illnesses per 100 full-time workers, close to the private-industry average of 2.3.

All other plastics product manufacturing
2.8
All private industry
2.3

0.9 of these cases per 100 workers involved days away from work.

United States, 2024. Industry: All other plastics product manufacturing (NAICS 326199). Source: U.S. Bureau of Labor Statistics, Survey of Occupational Injuries and Illnesses, Table 1: incidence rates of nonfatal occupational injuries and illnesses by industry and case types, 2024.

Workplace deaths

13 fatal work injuries in 2024.

Manufacturing
2.4
All workers
3.3

Deaths per 100,000 full-time equivalent workers, for the industry sector as a whole.

United States, private industry, 2024. Industry: Other Plastics Product Manufacturing (NAICS 32619), the closest published group. Source: U.S. Bureau of Labor Statistics, Census of Fatal Occupational Injuries; sector rates.

Most cited safety standards

1,008 citations from 312 inspections; 69% were classed serious, willful or repeat.

  • 1910.147 The control of hazardous energy (lockout/tagout)
    174
  • 1910.212 General requirements for all machines
    76
  • 1910.134 Respiratory protection
    58
  • 1910.1200 Hazard communication
    55
  • 1910.178 Powered industrial trucks
    47

Standards cited most often in this industry, by number of citations.

United States, citations issued October 2024 to September 2025 (federal fiscal year 2025). Industry: All Other Plastics Product Manufacturing (NAICS 326199). Covers federal and state-plan inspections. A citation is one violation item; one inspection can produce several. Source: U.S. Department of Labor, Occupational Safety and Health Administration, OSHA enforcement data (inspections and violations); standard titles from the Code of Federal Regulations, Title 29 (section headings).

Fire frequency

7,966 fires a year reported in industrial and manufacturing properties, causing about $810 million in direct property damage a year.

United States, 2020 to 2024, annual average. The group includes utility, defense, agriculture and mining properties. Source: National Fire Protection Association, Structure Fires in Industrial and Manufacturing Properties.

Toxic chemical releases

443 facilities reported toxic chemical releases totaling 10.5 million pounds on and off site.

  • Styrene
    8.7M
  • Methyl methacrylate
    268,278
  • Toluene
    201,989

Chemicals released in the largest amounts, in pounds. 314 of the facilities reported at least one chemical classed as a carcinogen.

United States, 2024. Industry: All Other Plastics Product Manufacturing (NAICS 326199). Covers facilities in listed industries with ten or more full-time employees that handle listed chemicals above set thresholds. Source: U.S. Environmental Protection Agency, Toxics Release Inventory basic data files.

Industry loss ratios by line2020 to 2024, the same table on every guide

Loss ratios are published by line of insurance, not by business type. They show how each line has run for insurers as a whole, whatever the business insured.

Published lineClosest line in this guide20202021202220232024
FireProperty63.2%67.3%62.4%45.5%40.9%
Commercial multiple perilProperty and liability sold as a package61.2%60.2%59.4%61.2%54.4%
Inland marineInland marine and equipment64.5%49.4%47.1%44.1%44.0%
Other liabilityPremises liability, and most umbrella, professional (other than medical) and cyber cover65.1%58.8%61.0%63.7%71.2%
Products liabilityProducts and completed work48.2%52.2%46.0%57.5%60.3%
Workers’ compensationWorkers’ injury47.9%49.2%45.0%44.3%46.0%
Commercial auto liabilityCommercial auto68.3%66.5%71.9%76.8%77.6%
Commercial auto physical damageCommercial auto50.9%56.3%64.3%65.1%57.9%

United States. Losses incurred as a percent of direct premiums earned, countrywide, before reinsurance and not including loss adjustment expense. Source: National Association of Insurance Commissioners, Report on Profitability by Line by State in 2024, ten-year summary.

Coverages to raise
Equipment breakdown
Large presses, extruder gearboxes and chillers fail without fire and stop lines that have no spare capacity.
Contingent business interruption
Specialty resins and colorants come from few producers, and one outage there leaves molders without material.
Product recall
Vehicle, appliance and medical buyers charge back recall costs for parts traced to one bad run.
Molds and tooling of others
Customers' molds fill the plant, are often worth more than the presses, and are rarely insured by anyone.
Classification
SystemCodeIndustry
NAICS 2022, primary326199All Other Plastics Product Manufacturing
NAICS 2022326160Plastics Bottle Manufacturing
NAICS 2022326122Plastics Pipe and Pipe Fitting Manufacturing
NAICS 2022326150Urethane and Other Foam Product (except Polystyrene) Manufacturing
NAICS 2022326140Polystyrene Foam Product Manufacturing
NAICS 2022326112Plastics Packaging Film and Sheet (including Laminated) Manufacturing
NAICS 2022326111Plastics Bag and Pouch Manufacturing
NAICS 2022326113Unlaminated Plastics Film and Sheet (except Packaging) Manufacturing
NAICS 2022326121Unlaminated Plastics Profile Shape Manufacturing
NAICS 2022326130Laminated Plastics Plate, Sheet (except Packaging), and Shape Manufacturing
NAICS 2022325991Custom Compounding of Purchased Resins
SIC 1987, primary3089Plastics Products, NEC
SIC 19873081Unsupported Plastics Film and Sheet
SIC 19873084Plastics Pipe
SIC 19873086Plastics Foam Products
Next step

See this risk on the map.

Book a 30-minute walkthrough tailored to your portfolio and perils of interest.

Request a Demo →