Body armor manufacturersNAICS 339113 · SIC 3842

Body armor manufacturers cut and stitch layered aramid and polyethylene fabrics into soft vests and press ceramic or composite plates for rifle protection, selling to police, military and security buyers. The product exists to stop bullets, so any failure is a death or serious injury claim.

NAICS 339113 Surgical Appliance and Supplies ManufacturingSIC 3842 Orthopedic, Prosthetic, and Surgical Appliances and Supplies

Manufacturing · Updated November 2026

01 / Loss drivers

Where losses come from.

  1. 01

    Armor that fails to stop a rated threat because of material degradation or a production fault

  2. 02

    Lot-wide recalls and replacement programs after a failed test or field incident

  3. 03

    Theft or diversion of controlled finished goods and costly ballistic fabric

How it comparesEach line’s rating against the average for its NAICS sector, Manufacturing (178 business types), and for all 747.
  1. PropertyProperty: Elevated, 3 of 5; sector average 3.7; all business types 2.9.
  2. Business interruptionBusiness interruption: Elevated, 3 of 5; sector average 3.5; all business types 2.7.
  3. Premises liabilityPremises liability: Low, 1 of 5; sector average 1.9; all business types 2.7.
  4. Products and completed workProducts and completed work: Severe, 5 of 5; sector average 3.4; all business types 2.6.
  5. Workers’ injuryWorkers’ injury: Elevated, 3 of 5; sector average 3.4; all business types 3.0.
  6. Commercial autoCommercial auto: Low, 1 of 5; sector average 2.3; all business types 2.5.
  7. Crime and theftCrime and theft: Elevated, 3 of 5; sector average 1.9; all business types 2.2.
  8. Inland marine and equipmentInland marine and equipment: Moderate, 2 of 5; sector average 2.6; all business types 2.6.
  9. EnvironmentalEnvironmental: Moderate, 2 of 5; sector average 2.8; all business types 2.3.
  10. Cyber and dataCyber and data: Elevated, 3 of 5; sector average 2.7; all business types 2.7.
  11. Professional liabilityProfessional liability: Moderate, 2 of 5; sector average 1.5; all business types 2.0.
  12. Umbrella and excessUmbrella and excess: Severe, 5 of 5; sector average 3.6; all business types 3.6.
What’s changing
  • Lighter polyethylene and hybrid ceramic plates are replacing heavier designs, but their performance depends on heat, age and handling, which raises testing demands.
  • Revised performance standards and test protocols require recertification of existing models, adding cost and the risk that models fail newer tests.
  • Online sales to civilians have grown, bringing buyers who store and wear armor poorly and wider debate over who may legally buy it.
02 / Line by line

Twelve lines, rated.

Each line shows its rating and the reason for it; open a line for what to watch for and the controls that matter. Ratings are UrbanStat’s own editorial view of a typical business of this type, on a five-step scale. They are a starting point for questions, not a quote, a rate or a statistical measure.

Property

Elevated
Ballistic fabrics and polyethylene sheet are costly and combustible, and plate pressing adds heated presses, resins and ovens.

Fire, explosion, water and weather damage to buildings, contents and stock.

Watch for
  • High-value fiber rolls concentrated in one unsprinklered store room
  • Hot presses and autoclaves running unattended overnight
  • Indoor test range with unburned powder and lead dust accumulation
Controls that matter
  • Sprinklers throughout, with fabric stock split between fire areas
  • Temperature limits and interlocks on presses and curing ovens
  • Range cleaning schedule with dedicated filtered ventilation

Business interruption

Elevated
Only a handful of mills make ballistic fiber, and each design must be recertified if materials or the site change.

How long and how costly a shutdown is.

Watch for
  • Single-source fiber or ceramic tile supply
  • Fixed-price government contracts with late-delivery penalties
Controls that matter
  • Buffer stock of certified materials held at a second location
  • Contract terms that allow for supply interruption

Premises liability

Low
Visitors are limited to buyers and auditors; live-fire demonstrations are the only unusual exposure.

Injuries to customers and the public, on site or caused by operations elsewhere.

Watch for
  • Demonstrations or range days for customers and the press
Controls that matter
  • Range safety officer and written rules for every live-fire event

Products and completed work

Severe
A vest or plate that lets a round through kills its wearer, and a material defect affects every unit in the lot.

Harm caused by what the business sells, serves, makes, installs or repairs.

Watch for
  • Fibers known to lose strength with heat, moisture or age
  • Protection levels claimed without current independent certification
  • Direct sales to consumers with no fitting or care guidance
Controls that matter
  • Lot-by-lot ballistic testing with retained samples and full traceability
  • Stated service life, care instructions and a replacement program
  • Fiber supplier agreements covering specification changes and indemnity

Workers’ injury

Elevated
Repetitive cutting and stitching of tough ballistic fabric, plus hot plate presses, ceramic dust and range lead and noise.

Injuries and illness to employees.

Watch for
  • Manual loading of heavy plate molds into hot presses
  • Lead and noise exposure for range staff
Controls that matter
  • Hoists at presses and cut-resistant gloves at cutting tables
  • Blood lead and hearing checks for range staff

Commercial auto

Low
Goods ship by carrier and staff rarely drive beyond sales visits.

Owned, hired and employee-driven vehicles, deliveries, customers’ vehicles in care.

Watch for
  • Sales staff carrying demonstration armor in personal cars
Controls that matter
  • Non-owned auto cover and driving record checks

Crime and theft

Elevated
Finished armor is restricted, sought after and easy to resell, and ballistic fabric carries a high price per roll.

Burglary, robbery, employee dishonesty, cash, payment and invoice fraud.

Watch for
  • No reconciliation of fabric issued against vests produced
  • Online orders shipped without buyer eligibility checks
Controls that matter
  • Caged stock, serial numbering and logged access
  • Buyer verification and export screening before release

Inland marine and equipment

Moderate
High-value shipments move to agencies and distributors, and samples travel to trade shows and test laboratories.

Property in transit, at job sites or in the insured’s care, and mobile equipment.

Watch for
  • Export consignments and large single contract deliveries
Controls that matter
  • Transit limits set to the largest single shipment

Environmental

Moderate
Resins, adhesives, solvent wipes and lead from the test range are the pollutants, all in small volumes.

Pollution on or from the site or the work.

Watch for
  • Bullet trap waste and range filters disposed of as ordinary trash
Controls that matter
  • Lead waste recycled through a licensed handler

Cyber and data

Elevated
Government buyers require protection of controlled design and test data, and ransomware can stop production and breach contract security terms.

Data breaches, ransomware, system outages and attacks on connected equipment.

Watch for
  • Export-controlled technical data stored on shared or cloud drives
  • Agency customer lists and officer sizing records held on file
Controls that matter
  • Access controls and logging that meet government contract security terms
  • Offline backups of designs, test records and production data

Professional liability

Moderate
Agencies rely on the maker's advice on threat levels, fitting and service life, and in-house test results support sales claims.

Loss or injury caused by advice, design, testing, care or another professional service.

Watch for
  • Testing services sold to other armor makers
  • Threat assessments or protection recommendations given to agencies
Controls that matter
  • Written scope and disclaimers on any test or advisory work
  • Fitting by trained staff, with measurements recorded and signed

Umbrella and excess

Severe
An armor failure kills or maims its wearer, and a lot-wide defect can bring many claims from agencies at once.

How likely one liability event is to exhaust primary limits.

Watch for
  • Large agency contracts covering many officers with one design
  • Sales to the public with little control over use
Controls that matter
  • Lot traceability that limits any recall to affected units
  • Contract terms capping liability and defining test acceptance
03 / Property picture

Construction, occupancy, protection, exposure.

What a risk engineer expects to find at a typical site of this type, and what to compare a submission against.

Construction
Modern light industrial buildings of steel or masonry, often with a secure stock room, an enclosed test range and offices for contract administration.
Occupancy
Cutting and stitching of aramid and polyethylene fabric, hot pressing and curing of plates with resins, and an indoor range with powder residue and lead dust.
Protection
Full sprinklers with fabric stock split between fire areas, interlocked press and oven controls, a ventilated and cleaned range, and monitored intrusion alarms with access control.
Exposure
Usually in industrial parks among other light manufacturers; perimeter fencing and lighting matter because finished armor and fabric attract targeted theft.
04 / Checklist

What to ask and look for.

Start with the desk review before quoting, then walk the site. Tick questions off as you go; ticks are kept in this browser only.

Before quoting: ask the broker or owner

Documents to request

On site: products and certification

On site: plant and security

On site: records

Refer or decline if you find

  • Protection ratings advertised without current independent certification
  • No lot traceability or retained test samples
  • Armor relabeled, refurbished or sold past stated service life
  • Materials changed after certification without retesting
05 / Location

How UrbanStat data helps.

Ballistic fabrics lose performance when wet, so flood or roof damage can condemn the whole stock, not only the soaked rolls. Restricted, resalable goods make neighborhood burglary rates a real factor.

FloodCrimeWindTornado
  • Crime scores at the address inform security conditions for a plant holding restricted, easily resold armor and costly fabric rolls.
  • Flood scores at the address show whether moisture-sensitive ballistic fabric stored at floor level is exposed before stock limits are set.
  • Underwriting rules drawn as areas on the map are enforced automatically, so armor stock submitted from a district closed to theft-attractive goods is referred at once.
Flood · Crime · Wind · Tornado
06 / Public loss data · NAICS 339113

What the published numbers say.

Official statistics for the industry or property type closest to this business. They describe the industry as a whole, not any one insured.

Workers’ injury frequency

1.9 recordable injuries and illnesses per 100 full-time workers, close to the private-industry average of 2.3.

Surgical appliance and supplies manufacturing
1.9
All private industry
2.3

0.4 of these cases per 100 workers involved days away from work.

United States, 2024. Industry: Surgical appliance and supplies manufacturing (NAICS 339113). Source: U.S. Bureau of Labor Statistics, Survey of Occupational Injuries and Illnesses, Table 1: incidence rates of nonfatal occupational injuries and illnesses by industry and case types, 2024.

Workplace deaths

4 fatal work injuries in 2024.

Manufacturing
2.4
All workers
3.3

Deaths per 100,000 full-time equivalent workers, for the industry sector as a whole.

United States, private industry, 2024. Industry: Medical Equipment and Supplies Manufacturing (NAICS 33911), the closest published group. Source: U.S. Bureau of Labor Statistics, Census of Fatal Occupational Injuries; sector rates.

Most cited safety standards

42 citations from 11 inspections; 48% were classed serious, willful or repeat.

  • 1910.1200 Hazard communication
    5
  • 1910.134 Respiratory protection
    5
  • 1910.132 General requirements (personal protective equipment)
    3
  • 1910.107 Spray finishing using flammable and combustible materials
    3
  • 1910.1025 Lead
    2

Standards cited most often in this industry, by number of citations.

United States, citations issued October 2024 to September 2025 (federal fiscal year 2025). Industry: Surgical Appliance and Supplies Manufacturing (NAICS 339113). Covers federal and state-plan inspections. A citation is one violation item; one inspection can produce several. Source: U.S. Department of Labor, Occupational Safety and Health Administration, OSHA enforcement data (inspections and violations); standard titles from the Code of Federal Regulations, Title 29 (section headings).

Fire frequency

7,966 fires a year reported in industrial and manufacturing properties, causing about $810 million in direct property damage a year.

United States, 2020 to 2024, annual average. The group includes utility, defense, agriculture and mining properties. Source: National Fire Protection Association, Structure Fires in Industrial and Manufacturing Properties.

Toxic chemical releases

40 facilities reported toxic chemical releases totaling 2.8 million pounds on and off site.

  • Ethylene glycol
    2.6M
  • Toluene
    40,796
  • Zinc compounds
    28,120

Chemicals released in the largest amounts, in pounds. 24 of the facilities reported at least one chemical classed as a carcinogen.

United States, 2024. Industry: Surgical Appliance and Supplies Manufacturing (NAICS 339113). Covers facilities in listed industries with ten or more full-time employees that handle listed chemicals above set thresholds. Source: U.S. Environmental Protection Agency, Toxics Release Inventory basic data files.

Industry loss ratios by line2020 to 2024, the same table on every guide

Loss ratios are published by line of insurance, not by business type. They show how each line has run for insurers as a whole, whatever the business insured.

Published lineClosest line in this guide20202021202220232024
FireProperty63.2%67.3%62.4%45.5%40.9%
Commercial multiple perilProperty and liability sold as a package61.2%60.2%59.4%61.2%54.4%
Inland marineInland marine and equipment64.5%49.4%47.1%44.1%44.0%
Other liabilityPremises liability, and most umbrella, professional (other than medical) and cyber cover65.1%58.8%61.0%63.7%71.2%
Products liabilityProducts and completed work48.2%52.2%46.0%57.5%60.3%
Workers’ compensationWorkers’ injury47.9%49.2%45.0%44.3%46.0%
Commercial auto liabilityCommercial auto68.3%66.5%71.9%76.8%77.6%
Commercial auto physical damageCommercial auto50.9%56.3%64.3%65.1%57.9%

United States. Losses incurred as a percent of direct premiums earned, countrywide, before reinsurance and not including loss adjustment expense. Source: National Association of Insurance Commissioners, Report on Profitability by Line by State in 2024, ten-year summary.

Coverages to raise
Product recall
A failed lot test forces agencies to pull and replace vests or plates across many officers at once.
Equipment breakdown
Hydraulic plate presses, autoclaves and cutting machines fail without fire and delay contract deliveries.
Export and ocean cargo
Export consignments of high-value armor travel by sea and air to buyers abroad, often under strict delivery terms.

NAICS and SIC codes for body armor manufacturers

SystemCodeIndustry
NAICS 2022, primary339113Surgical Appliance and Supplies Manufacturing
SIC 1987, primary3842Orthopedic, Prosthetic, and Surgical Appliances and Supplies
Next step

See this risk on the map.

Book a 30-minute walkthrough tailored to your portfolio and perils of interest.

Request a Demo →