Semiconductor manufacturers
Semiconductor manufacturers build integrated circuits on silicon wafers in cleanrooms, using hundreds of process steps with toxic, corrosive and pyrophoric gases. Enormous value sits in a small space, and a brief fire, leak, power dip or contamination event scraps wafers and idles tools for months.
Where losses come from.
- 01
Cleanroom contamination from small fires, smoke, leaks or water spreading through recirculated air
- 02
Loss of power, ultrapure water or process gases scrapping wafers in progress
- 03
Long requalification and tool replacement times after any damage
- PropertyProperty: Severe, 5 of 5; sector average 3.7; all business types 2.9.
- Business interruptionBusiness interruption: Severe, 5 of 5; sector average 3.5; all business types 2.7.
- Premises liabilityPremises liability: Moderate, 2 of 5; sector average 1.9; all business types 2.7.
- Products and completed workProducts and completed work: Elevated, 3 of 5; sector average 3.4; all business types 2.6.
- Workers’ injuryWorkers’ injury: Elevated, 3 of 5; sector average 3.4; all business types 3.0.
- Commercial autoCommercial auto: Low, 1 of 5; sector average 2.3; all business types 2.5.
- Crime and theftCrime and theft: Elevated, 3 of 5; sector average 1.9; all business types 2.2.
- Inland marine and equipmentInland marine and equipment: High, 4 of 5; sector average 2.6; all business types 2.6.
- EnvironmentalEnvironmental: High, 4 of 5; sector average 2.8; all business types 2.3.
- Cyber and dataCyber and data: High, 4 of 5; sector average 2.7; all business types 2.7.
- Professional liabilityProfessional liability: Moderate, 2 of 5; sector average 1.5; all business types 2.0.
- Umbrella and excessUmbrella and excess: Elevated, 3 of 5; sector average 3.6; all business types 3.6.
- New fabs are going up in places with little chipmaking history, where tool installers, gas suppliers and experienced fire responders are scarce.
- Advanced packaging and stacked chips add process steps and handoffs between sites, so a fire at one packaging plant now stalls many customers' products.
- Pressure to cut fluorinated chemicals and water use brings new process chemistry and recycling plant, adding change risk to tightly controlled lines.
Twelve lines, rated.
Each line shows its rating and the reason for it; open a line for what to watch for and the controls that matter. Ratings are UrbanStat’s own editorial view of a typical business of this type, on a five-step scale. They are a starting point for questions, not a quote, a rate or a statistical measure.
Property
SeverePlastic wet benches, pyrophoric and flammable gases and tools worth fortunes share recirculated air, so a small fire becomes a huge loss.
Fire, explosion, water and weather damage to buildings, contents and stock.
- Combustible plastic wet benches and exhaust ducts without internal protection
- Silane and hydrogen supply lacking automatic shut-off and leak detection
- Cleanroom wall and ceiling panels with combustible cores
- Fire-safe bench materials or fixed suppression inside benches and ducts
- Gas cabinets with detection, excess-flow valves and automatic isolation
- Very early smoke detection sampling the return air
Business interruption
SevereOne fab supplies customers with no alternative source, lithography and deposition tools take a year or more to replace, and restart needs requalification.
How long and how costly a shutdown is.
- A single site producing a node or product family
- Dependence on one utility feed, gas plant or water source
- Customer contracts with supply guarantees
- Dual power feeds with ride-through for critical tools
- Recovery plans agreed with tool makers and cleanroom contractors
- Qualified second fab or foundry for key products
Premises liability
ModerateThe public stays out, but a toxic gas release or chemical spill can force evacuation of neighboring properties.
Injuries to customers and the public, on site or caused by operations elsewhere.
- Housing, schools or offices close to the bulk gas pad
- Bulk chemical deliveries crossing public roads on site
- Fence-line gas monitoring and a rehearsed community alert plan
- Scrubbers sized for worst-case releases
Products and completed work
ElevatedChips rarely injure anyone directly, but a latent defect in automotive, medical or industrial parts triggers expensive recalls.
Harm caused by what the business sells, serves, makes, installs or repairs.
- Chips sold for safety-critical vehicle or medical use
- Contracts accepting recall or line-down costs without a cap
- Wafer-lot traceability through packaging and test
- Liability caps and application limits written into sales terms
Workers’ injury
ElevatedArsine, phosphine, hydrofluoric acid and solvents are deadly in small amounts, though engineering controls keep actual injury rates low.
Injuries and illness to employees.
- Maintenance crews opening tools and gas lines
- Contractors working in subfloor and utility levels
- Lockout, purge and gas-detection procedures for every tool intervention
- On-site emergency response team and first aid for acid burns
Commercial auto
LowStaff seldom drive for work and product ships by specialist carrier.
Owned, hired and employee-driven vehicles, deliveries, customers’ vehicles in care.
- Shuttle vans running between sites on a campus
- Hired and non-owned auto cover for incidental driving
Crime and theft
ElevatedFinished chips and wafers are tiny, extremely valuable and traceable only with effort, and process know-how is worth stealing.
Burglary, robbery, employee dishonesty, cash, payment and invoice fraud.
- Finished goods handled outside a secured, counted area
- Scrap wafers and rejected die leaving without destruction
- Vaulted finished goods with access logs and reconciliation
- Certified destruction of scrap and controls on design data
Inland marine and equipment
HighWafers and tools in transit are fragile and worth a great deal per crate, and new tools are insured through rigging and installation.
Property in transit, at job sites or in the insured’s care, and mobile equipment.
- Tool move-in handled without specialist riggers
- Air shipments of wafers between fab, packaging and test sites
- Photomasks with no duplicates held elsewhere
- Shock, tilt and humidity recorders on every tool and wafer shipment
- Transit and installation limits set per tool value
Environmental
HighHydrofluoric acid, solvents, arsenic and fluorinated compounds flow through large wastewater and exhaust treatment systems every hour.
Pollution on or from the site or the work.
- Older sites with historic solvent contamination in groundwater
- Double-contained piping and trenches with no leak monitoring
- Wastewater treatment near capacity as production grows
- Monitored secondary containment for chemical distribution and waste lines
- Continuous monitoring of fluoride, metals and pH before discharge
- Exhaust abatement on every toxic and fluorinated gas process
Cyber and data
HighTools, recipes and wafer tracking run on connected systems, so ransomware or tampering halts the fab, and chip designs attract theft.
Data breaches, ransomware, system outages and attacks on connected equipment.
- Tool makers with standing remote access to production equipment
- Older tool controllers running unsupported operating systems
- Customer design files copied across many internal systems
- Production network segmented from office systems, with monitored vendor access
- Malware scanning of every file and portable drive entering the fab
- Customer design data held in restricted, logged environments
Professional liability
ModerateFoundries supply design rules, circuit libraries and process advice, and a customer can claim lost revenue when chips miss their specification.
Loss or injury caused by advice, design, testing, care or another professional service.
- Design services or licensed circuit blocks sold alongside wafer production
- Yield or performance commitments written into customer agreements
- Contracts limiting liability to the price of the affected wafers
- Design-rule and library changes released only after documented qualification
Umbrella and excess
ElevatedA latent defect in chips for vehicles or medical devices, or a toxic gas release into nearby homes, can exceed primary limits.
How likely one liability event is to exhaust primary limits.
- Safety-critical automotive or implantable medical applications
- Housing or schools within reach of a toxic gas release
- Application restrictions and liability caps in sales terms
- Toxic gas inventories kept to a minimum, with scrubbed exhaust
Construction, occupancy, protection, exposure.
What a risk engineer expects to find at a typical site of this type, and what to compare a submission against.
- Construction
- Large steel-frame fabs with the cleanroom set between a subfab utility level and an air-handling plenum, long-span roofs, and wall and ceiling panels that may have combustible cores.
- Occupancy
- Plastic wet benches, silane, hydrogen, toxic dopant gases, solvents and acids feed hundreds of tools under recirculated air that carries smoke across the whole cleanroom.
- Protection
- Sprinklers above and below the cleanroom, suppression inside benches and exhaust ducts, air-sampling smoke detection, gas cabinets with automatic isolation and an on-site emergency team.
- Exposure
- Fabs cluster in science parks beside suppliers, gas plants and other fabs; the bulk gas pad, chemical yard and any nearby housing set the off-site exposure.
What to ask and look for.
Start with the desk review before quoting, then walk the site. Tick questions off as you go; ticks are kept in this browser only.
Before quoting: ask the broker or owner
Documents to request
On site: fab and products
On site: cleanroom fire protection
On site: utilities and recovery
On site: environment and people
Refer or decline if you find
- Combustible wet benches with no internal fire suppression
- Pyrophoric gas supply without automatic shut-off on leak detection
- Single utility feed with no ride-through for critical tools
- Known groundwater contamination with no funded remediation plan
- Sole fab for a product with no qualified alternative
How UrbanStat data helps.
Fabs cluster in a few regions, several of them seismic. Shaking misaligns tools and breaks quartz and gas lines even when the building stands. Power or water loss after a storm scraps wafers, and wildfire smoke loads air filtration.
- Earthquake scores at the address inform terms where modest shaking misaligns lithography tools and ruptures gas and chemical lines.
- Street-by-street exposure views show total insured value across a fab, its neighbors and its suppliers in one science park, with alerts at a set threshold.
- Live event overlays during a hurricane or wildfire show which fabs and supplier sites are in the path, where losing power or water scraps wafers in process.
What the published numbers say.
Official statistics for the industry or property type closest to this business. They describe the industry as a whole, not any one insured.
0.8 recordable injuries and illnesses per 100 full-time workers, below the private-industry average of 2.3.
0.3 of these cases per 100 workers involved days away from work.
United States, 2024. Industry: Semiconductor and related device manufacturing (NAICS 334413). Source: U.S. Bureau of Labor Statistics, Survey of Occupational Injuries and Illnesses, Table 1: incidence rates of nonfatal occupational injuries and illnesses by industry and case types, 2024.
9 fatal work injuries in 2024.
Deaths per 100,000 full-time equivalent workers, for the industry sector as a whole.
United States, private industry, 2024. Industry: Computer and Electronic Product Manufacturing (NAICS 334), the closest published group. Source: U.S. Bureau of Labor Statistics, Census of Fatal Occupational Injuries; sector rates.
36 citations from 14 inspections; 47% were classed serious, willful or repeat.
- 1910.147 The control of hazardous energy (lockout/tagout)6
- 1910.1200 Hazard communication4
- 1910.305 Wiring methods, components, and equipment for general use4
- 1910.134 Respiratory protection3
- 1910.132 General requirements (personal protective equipment)2
Standards cited most often in this industry, by number of citations.
United States, citations issued October 2024 to September 2025 (federal fiscal year 2025). Industry: Semiconductor and Related Device Manufacturing (NAICS 334413). Covers federal and state-plan inspections. A citation is one violation item; one inspection can produce several. Source: U.S. Department of Labor, Occupational Safety and Health Administration, OSHA enforcement data (inspections and violations); standard titles from the Code of Federal Regulations, Title 29 (section headings).
7,966 fires a year reported in industrial and manufacturing properties, causing about $810 million in direct property damage a year.
United States, 2020 to 2024, annual average. The group includes utility, defense, agriculture and mining properties. Source: National Fire Protection Association, Structure Fires in Industrial and Manufacturing Properties.
92 facilities reported toxic chemical releases totaling 3.8 million pounds on and off site.
- Nitrate compounds1.6M
- Ammonia771,297
- Zinc compounds289,636
Chemicals released in the largest amounts, in pounds. 17 of the facilities reported at least one chemical classed as a carcinogen.
United States, 2024. Industry: Semiconductor and Related Device Manufacturing (NAICS 334413). Covers facilities in listed industries with ten or more full-time employees that handle listed chemicals above set thresholds. Source: U.S. Environmental Protection Agency, Toxics Release Inventory basic data files.
Industry loss ratios by line2020 to 2024, the same table on every guide
Loss ratios are published by line of insurance, not by business type. They show how each line has run for insurers as a whole, whatever the business insured.
| Published line | Closest line in this guide | 2020 | 2021 | 2022 | 2023 | 2024 |
|---|---|---|---|---|---|---|
| Fire | Property | 63.2% | 67.3% | 62.4% | 45.5% | 40.9% |
| Commercial multiple peril | Property and liability sold as a package | 61.2% | 60.2% | 59.4% | 61.2% | 54.4% |
| Inland marine | Inland marine and equipment | 64.5% | 49.4% | 47.1% | 44.1% | 44.0% |
| Other liability | Premises liability, and most umbrella, professional (other than medical) and cyber cover | 65.1% | 58.8% | 61.0% | 63.7% | 71.2% |
| Products liability | Products and completed work | 48.2% | 52.2% | 46.0% | 57.5% | 60.3% |
| Workers’ compensation | Workers’ injury | 47.9% | 49.2% | 45.0% | 44.3% | 46.0% |
| Commercial auto liability | Commercial auto | 68.3% | 66.5% | 71.9% | 76.8% | 77.6% |
| Commercial auto physical damage | Commercial auto | 50.9% | 56.3% | 64.3% | 65.1% | 57.9% |
United States. Losses incurred as a percent of direct premiums earned, countrywide, before reinsurance and not including loss adjustment expense. Source: National Association of Insurance Commissioners, Report on Profitability by Line by State in 2024, ten-year summary.
- Contingent business interruption
- A fire or outage at a sole gas, chemical, wafer or packaging supplier stops output as surely as damage at the fab.
- Utility service interruption
- Off-site loss of power, water or gas stops the fab, and ordinary interruption cover responds only to damage on site.
- Equipment breakdown
- Lithography, deposition and etch tools fail electrically or mechanically without fire, and replacements take many months.
- Product recall
- Automotive and device makers pass back the cost of tracing and replacing parts built with a defective wafer lot.
- Pollution legal liability
- Solvent, fluoride and metal releases to groundwater or air fall outside general liability and are slow to clean up.
See this risk on the map.
Book a 30-minute walkthrough tailored to your portfolio and perils of interest.