Household appliance manufacturers

Appliance makers stamp, coat and assemble refrigerators, ranges, washers, dryers, water heaters and countertop and floor-care products. The plants run presses, enamel and powder lines, foam injection and refrigerant charging, and every unit ends up plugged in or piped to gas inside a home, where one defect repeats across a whole model line.

Manufacturing · NAICS 335220 · SIC 3632 · Updated November 2026

01 / Loss drivers

Where losses come from.

  1. 01

    House fires, gas leaks and shocks traced to a design or component defect repeated across a model

  2. 02

    Fires and explosions at foam injection, hydrocarbon refrigerant charging and paint or enamel lines

  3. 03

    Hand injuries at presses, sheet metal cuts and strains on fast assembly lines

How it comparesEach line’s rating against the average for its NAICS sector, Manufacturing (178 business types), and for all 747.
  1. PropertyProperty: High, 4 of 5; sector average 3.7; all business types 2.9.
  2. Business interruptionBusiness interruption: High, 4 of 5; sector average 3.5; all business types 2.7.
  3. Premises liabilityPremises liability: Moderate, 2 of 5; sector average 1.9; all business types 2.7.
  4. Products and completed workProducts and completed work: Severe, 5 of 5; sector average 3.4; all business types 2.6.
  5. Workers’ injuryWorkers’ injury: Elevated, 3 of 5; sector average 3.4; all business types 3.0.
  6. Commercial autoCommercial auto: Moderate, 2 of 5; sector average 2.3; all business types 2.5.
  7. Crime and theftCrime and theft: Moderate, 2 of 5; sector average 1.9; all business types 2.2.
  8. Inland marine and equipmentInland marine and equipment: Moderate, 2 of 5; sector average 2.6; all business types 2.6.
  9. EnvironmentalEnvironmental: Elevated, 3 of 5; sector average 2.8; all business types 2.3.
  10. Cyber and dataCyber and data: Elevated, 3 of 5; sector average 2.7; all business types 2.7.
  11. Professional liabilityProfessional liability: Low, 1 of 5; sector average 1.5; all business types 2.0.
  12. Umbrella and excessUmbrella and excess: Severe, 5 of 5; sector average 3.6; all business types 3.6.
What’s changing
  • Hydrocarbon refrigerants and blowing agents are replacing older gases for climate reasons, cutting environmental exposure but adding flammable gas in the plant and in homes.
  • Connected appliances with app control and remote start bring firmware, data privacy and remote-operation risks into product design.
  • Cordless vacuums and other battery-powered appliances, plus induction cooktops, add lithium-ion cells and power electronics, shifting product fires toward batteries and circuit boards.
02 / Line by line

Twelve lines, rated.

Each line shows its rating and the reason for it; open a line for what to watch for and the controls that matter. Ratings are UrbanStat’s own editorial view of a typical business of this type, on a five-step scale. They are a starting point for questions, not a quote, a rate or a statistical measure.

Property

High
Flammable foam blowing agents and refrigerant gases, enamel furnaces and powder booths sit beside warehouses of boxed goods packed in plastic foam.

Fire, explosion, water and weather damage to buildings, contents and stock.

Watch for
  • Cyclopentane or other hydrocarbon foaming without gas detection and ventilation interlocks
  • Propane or isobutane refrigerant charging stations open to the assembly floor
  • Finished goods racked high in cartons with expanded plastic packaging
Controls that matter
  • Gas detection that stops foaming and charging and boosts exhaust on alarm
  • In-rack sprinklers designed for cartoned plastics in finished goods storage
  • Flame detection and automatic shutdown on powder and paint booths

Business interruption

High
Press lines, enamel furnaces and foaming fixtures are custom built, and compressors, control boards and motors come from few suppliers.

How long and how costly a shutdown is.

Watch for
  • One plant building a whole product category with no second source
  • Compressors, control boards or chips from a single overseas supplier
  • Peak shipping ahead of holiday and promotional seasons
Controls that matter
  • Second-source qualification for compressors, motors and electronic controls
  • Spare dies and critical fixtures stored away from the main plant

Premises liability

Moderate
Carrier drivers at the docks and contractors in the plant are the main visitors; the public rarely enters.

Injuries to customers and the public, on site or caused by operations elsewhere.

Watch for
  • Factory outlet, test kitchen or consumer events open to the public
  • Carrier drivers helping load at docks and in trailer yards
Controls that matter
  • Visitor escorts and marked walkways through production areas
  • Dock rules keeping drivers in a waiting area away from forklift traffic

Products and completed work

Severe
Appliances fail inside occupied homes, so one defect repeats as house fires, gas explosions, shocks or children crushed under tipping ranges.

Harm caused by what the business sells, serves, makes, installs or repairs.

Watch for
  • Imported cords, thermostats, relays or heating elements with unverified safety listings
  • Dryers, space heaters and appliances with lithium-ion battery packs
  • Water valves, hoses and ice maker lines that leak and flood homes
Controls that matter
  • Independent safety listing per model, plus end-of-line electrical and gas leak tests
  • Serial number traceability linking each unit to component lots and test results
  • Anti-tip brackets, thermal cutoffs and overheat protection built into designs

Workers’ injury

Elevated
Presses, sheet metal edges, isocyanates from foaming and repetitive motion on paced assembly lines cause cuts, strains and asthma.

Injuries and illness to employees.

Watch for
  • Hand feeding or unjamming presses and brake forming machines
  • Line speeds raised without changes to staffing or workstation design
  • Isocyanate exposure at foam injection without air monitoring
Controls that matter
  • Cut-resistant sleeves and gloves for anyone handling sheet metal
  • Ergonomic review of each workstation whenever line rates change
  • Lockout and die-blocking procedures audited at every press

Commercial auto

Moderate
Finished goods leave by contract carrier; company vehicles are sales cars, service vans and yard tractors.

Owned, hired and employee-driven vehicles, deliveries, customers’ vehicles in care.

Watch for
  • Own fleet delivering and installing appliances in customers' homes
Controls that matter
  • Driving record checks and telematics on any delivery or service fleet

Crime and theft

Moderate
Copper tubing, compressors and boxed small appliances have resale value, but stock is bulky and values per unit are ordinary.

Burglary, robbery, employee dishonesty, cash, payment and invoice fraud.

Watch for
  • Trailer loads of small appliances parked unsecured in the yard
  • Copper and aluminum scrap sold without weight reconciliation
Controls that matter
  • Sealed and tracked trailers with yard cameras and gate control
  • Scrap sales matched to material usage by someone outside the shop

Inland marine and equipment

Moderate
Most finished goods move under carrier or buyer terms; the exposure is imported components, molds at suppliers and goods in warehouses.

Property in transit, at job sites or in the insured’s care, and mobile equipment.

Watch for
  • Injection molds and dies owned by the insured but held at suppliers
  • Consigned stock at third-party distribution centers
Controls that matter
  • A tooling register with location, ownership and replacement values
  • Ocean and transit cover for imported components and finished goods

Environmental

Elevated
Isocyanates, blowing agents, refrigerants, enamel frit, phosphate pretreatment and degreasing solvents generate emissions, sludges and legacy soil concerns.

Pollution on or from the site or the work.

Watch for
  • Refrigerant vented during charging, rework or scrapping of failed units
  • Past chlorinated solvent degreasing or chromate pretreatment at older plants
Controls that matter
  • Refrigerant recovery at rework stations with logged quantities
  • Licensed disposal of pretreatment sludge, paint and foam waste

Cyber and data

Elevated
Networked presses, robots and test stations pace the line, and warranty registrations and appliance apps hold owners' names, addresses and usage data.

Data breaches, ransomware, system outages and attacks on connected equipment.

Watch for
  • Connected appliances with app accounts, remote start or firmware updates
  • Production controls on the same network as office systems
Controls that matter
  • Segmented plant networks with offline backups of production programs
  • Signed firmware updates and a process for reporting appliance vulnerabilities

Professional liability

Low
Design faults fall under products; separate advice or design services are rarely sold.

Loss or injury caused by advice, design, testing, care or another professional service.

Watch for
  • Engineering or design work sold to other brands for a fee
Controls that matter
  • Contracts defining design responsibility for private-label products

Umbrella and excess

Severe
One defective component across a model line can bring fire deaths, many subrogation suits and class actions at once.

How likely one liability event is to exhaust primary limits.

Watch for
  • High sales volumes of gas, heating or high-wattage appliances
  • Products sold under retailers' brands with broad indemnity agreements
Controls that matter
  • Field incident tracking that spots repeat failures and triggers engineering review
  • A rehearsed recall plan covering suppliers, retailers and the product safety authority
03 / Property picture

Construction, occupancy, protection, exposure.

What a risk engineer expects to find at a typical site of this type, and what to compare a submission against.

Construction
Large single-story steel-frame plants with metal roofs and long spans, often extended many times, with attached high-bay warehouses and enclosed truck docks.
Occupancy
Coil stamping, welding and brazing, enamel or powder coating, plastic molding, foam injection with flammable blowing agents, refrigerant charging and storage of cartoned goods in plastic packaging.
Protection
Full sprinklers with in-rack protection in storage, gas detection and explosion venting at foaming and charging, booth suppression, monitored alarms and a trained plant emergency team.
Exposure
Usually sited in industrial parks beside suppliers and logistics buildings; trailer yards and outdoor tanks of blowing agent and refrigerant sit close to the main building.
04 / Checklist

What to ask and look for.

Start with the desk review before quoting, then walk the site. Tick questions off as you go; ticks are kept in this browser only.

Before quoting: ask the broker or owner

Documents to request

On site: production and processes

On site: quality and testing

On site: storage and protection

On site: people and records

Refer or decline if you find

  • Hydrocarbon foaming or charging with no gas detection or interlocks
  • Models sold with no independent safety listing
  • Repeat field fire reports with no engineering investigation
  • Cartoned plastics stored above the sprinkler design height
  • Retailer contracts accepting unlimited recall and indemnity costs
05 / Location

How UrbanStat data helps.

Wide-span metal roofs over plants and warehouses take tornado, wind and hail damage, and a roof breach soaks cartoned stock. Flooding of press pits, electrical rooms and floor-level finished goods stops shipping.

TornadoWindHailFlood
  • Tornado, wind and hail scores at the address inform roof and deductible terms for wide-span plants and warehouses full of cartoned appliances.
  • Street-by-street exposure views show accumulations where an appliance plant, its suppliers and its distribution warehouses share one industrial park, with alerts past a set threshold.
  • Parcel and permit data give construction dates and the history of building additions, a quick check on whether sprinkler design kept pace with expansions.
Tornado · Wind · Hail · Flood
06 / Public loss data

What the published numbers say.

Official statistics for the industry or property type closest to this business. They describe the industry as a whole, not any one insured.

Workers’ injury frequency

2.3 recordable injuries and illnesses per 100 full-time workers, close to the private-industry average of 2.3.

Major household appliance manufacturing
2.3
All private industry
2.3

0.6 of these cases per 100 workers involved days away from work.

United States, 2024. Industry: Major household appliance manufacturing (NAICS 33522), the closest published group. Source: U.S. Bureau of Labor Statistics, Survey of Occupational Injuries and Illnesses, Table 1: incidence rates of nonfatal occupational injuries and illnesses by industry and case types, 2024.

Workplace deaths

5 fatal work injuries in 2024.

Manufacturing
2.4
All workers
3.3

Deaths per 100,000 full-time equivalent workers, for the industry sector as a whole.

United States, private industry, 2024. Industry: Electrical Equipment, Appliance, and Component Manufacturing (NAICS 335), the closest published group. Source: U.S. Bureau of Labor Statistics, Census of Fatal Occupational Injuries; sector rates.

Most cited safety standards

14 citations from 5 inspections; 29% were classed serious, willful or repeat.

  • 1910.147 The control of hazardous energy (lockout/tagout)
    8
  • 1910.212 General requirements for all machines
    1
  • 1910.1200 Hazard communication
    1
  • 1910.28 Duty to have fall protection and falling object protection
    1
  • 1910.22 General requirements (walking-working surfaces)
    1

Standards cited most often in this industry, by number of citations.

United States, citations issued October 2024 to September 2025 (federal fiscal year 2025). Industry: Major Household Appliance Manufacturing (NAICS 335220). Covers federal and state-plan inspections. A citation is one violation item; one inspection can produce several. Source: U.S. Department of Labor, Occupational Safety and Health Administration, OSHA enforcement data (inspections and violations); standard titles from the Code of Federal Regulations, Title 29 (section headings).

Fire frequency

7,966 fires a year reported in industrial and manufacturing properties, causing about $810 million in direct property damage a year.

United States, 2020 to 2024, annual average. The group includes utility, defense, agriculture and mining properties. Source: National Fire Protection Association, Structure Fires in Industrial and Manufacturing Properties.

Toxic chemical releases

33 facilities reported toxic chemical releases totaling 503,984 pounds on and off site.

  • Certain glycol ethers
    100,963
  • Manganese and manganese compounds
    48,725
  • Nitrate compounds
    42,150

Chemicals released in the largest amounts, in pounds. 24 of the facilities reported at least one chemical classed as a carcinogen.

United States, 2024. Industry: Major Household Appliance Manufacturing (NAICS 335220). Covers facilities in listed industries with ten or more full-time employees that handle listed chemicals above set thresholds. Source: U.S. Environmental Protection Agency, Toxics Release Inventory basic data files.

Industry loss ratios by line2020 to 2024, the same table on every guide

Loss ratios are published by line of insurance, not by business type. They show how each line has run for insurers as a whole, whatever the business insured.

Published lineClosest line in this guide20202021202220232024
FireProperty63.2%67.3%62.4%45.5%40.9%
Commercial multiple perilProperty and liability sold as a package61.2%60.2%59.4%61.2%54.4%
Inland marineInland marine and equipment64.5%49.4%47.1%44.1%44.0%
Other liabilityPremises liability, and most umbrella, professional (other than medical) and cyber cover65.1%58.8%61.0%63.7%71.2%
Products liabilityProducts and completed work48.2%52.2%46.0%57.5%60.3%
Workers’ compensationWorkers’ injury47.9%49.2%45.0%44.3%46.0%
Commercial auto liabilityCommercial auto68.3%66.5%71.9%76.8%77.6%
Commercial auto physical damageCommercial auto50.9%56.3%64.3%65.1%57.9%

United States. Losses incurred as a percent of direct premiums earned, countrywide, before reinsurance and not including loss adjustment expense. Source: National Association of Insurance Commissioners, Report on Profitability by Line by State in 2024, ten-year summary.

Coverages to raise
Product recall
A recall of a whole model line costs notification, retrieval, repair and retailer charges that general liability excludes.
Equipment breakdown
Press clutches, enamel furnaces, compressors and transformers fail without fire and stop paced lines.
Contingent business interruption
A fire at the sole supplier of compressors, motors or control boards stops assembly as surely as a fire at the plant.
Ocean cargo
Imported components and finished small appliances travel by sea for weeks before reaching the plant or warehouse.
Classification
SystemCodeIndustry
NAICS 2022, primary335220Major Household Appliance Manufacturing
NAICS 2022335210Small Electrical Appliance Manufacturing
SIC 1987, primary3632Household Refrigerators and Home and Farm Freezers
SIC 19873633Household Laundry Equipment
SIC 19873631Household Cooking Equipment
SIC 19873634Electric Housewares and Fans
Next step

See this risk on the map.

Book a 30-minute walkthrough tailored to your portfolio and perils of interest.

Request a Demo →