Electroplating and metal finishing shopsNAICS 332813 · SIC 3471
Plating shops clean customers' metal parts and coat them in tanks of acids, cyanides and metal salts, using rectifiers, heaters and exhaust scrubbers. Corrosive air attacks wiring and steel, heated plastic tanks catch fire, and every spill or rinse carries heavy metals toward the drain.
NAICS 332813 Electroplating, Plating, Polishing, Anodizing, and ColoringSIC 3471 Electroplating, Plating, Polishing, Anodizing, and Coloring
Where losses come from.
- 01
Soil and groundwater contamination from tank leaks, floor trenches and decades of rinse water
- 02
Fires started by immersion heaters in plastic tanks or by corroded electrical gear
- 03
Chemical burns, toxic fume exposure and slips among line operators
- PropertyProperty: High, 4 of 5; sector average 3.7; all business types 2.9.
- Business interruptionBusiness interruption: Elevated, 3 of 5; sector average 3.5; all business types 2.7.
- Premises liabilityPremises liability: Moderate, 2 of 5; sector average 1.9; all business types 2.7.
- Products and completed workProducts and completed work: Elevated, 3 of 5; sector average 3.4; all business types 2.6.
- Workers’ injuryWorkers’ injury: High, 4 of 5; sector average 3.4; all business types 3.0.
- Commercial autoCommercial auto: Moderate, 2 of 5; sector average 2.3; all business types 2.5.
- Crime and theftCrime and theft: Moderate, 2 of 5; sector average 1.9; all business types 2.2.
- Inland marine and equipmentInland marine and equipment: Elevated, 3 of 5; sector average 2.6; all business types 2.6.
- EnvironmentalEnvironmental: High, 4 of 5; sector average 2.8; all business types 2.3.
- Cyber and dataCyber and data: Moderate, 2 of 5; sector average 2.7; all business types 2.7.
- Professional liabilityProfessional liability: Moderate, 2 of 5; sector average 1.5; all business types 2.0.
- Umbrella and excessUmbrella and excess: Elevated, 3 of 5; sector average 3.6; all business types 3.6.
- Hexavalent chromium and other legacy chemistries are being phased down, and switching to trivalent or alternative processes brings new baths, controls and quality risks during the changeover.
- Tighter discharge limits and restrictions on persistent fume suppressants put older wastewater systems out of compliance and raise the cost of cleaning up a contaminated site.
- Electric vehicle, battery and electronics work brings new finishes and automated high-volume lines, while automated hoists cut operator contact with open tanks.
Twelve lines, rated.
Each line shows its rating and the reason for it; open a line for what to watch for and the controls that matter. Ratings are UrbanStat’s own editorial view of a typical business of this type, on a five-step scale. They are a starting point for questions, not a quote, a rate or a statistical measure.
Property
HighImmersion heaters, plastic tanks and plastic exhaust ducts sit in an atmosphere that corrodes wiring, sprinklers and structural steel.
Fire, explosion, water and weather damage to buildings, contents and stock.
- Heaters with no low-liquid cutoff, or left energized overnight
- Plastic fume ducts and scrubbers with no sprinklers inside
- Nitric or chromic acid stored beside solvents, lacquers or other organics
- Low-level and over-temperature cutoffs on every heated tank
- Corrosion-resistant sprinklers and wiring, inspected and replaced on schedule
- Acids, cyanides and oxidizers in separate, curbed storage rooms
Business interruption
ElevatedA tank line fire or a suspended discharge permit stops all work, and customers move parts to another finisher quickly.
How long and how costly a shutdown is.
- One rectifier, scrubber or wastewater unit serving every line
- Aerospace or medical approvals tied to this specific site
- Spare rectifiers, pumps and heaters held on site
- Standing arrangement with another approved finisher for overflow work
Premises liability
ModerateFew visitors, but a fume release or chemical reaction can reach neighboring units and passers-by.
Injuries to customers and the public, on site or caused by operations elsewhere.
- Shared multi-tenant building with common walls or ventilation
- Bulk chemical deliveries pumped in from the street side
- Labeled fill connections and supervised bulk deliveries
- Emergency plan agreed with neighbors and the fire service
Products and completed work
ElevatedA coating that flakes, corrodes early or embrittles a high-strength part can fail in a vehicle, aircraft or machine.
Harm caused by what the business sells, serves, makes, installs or repairs.
- High-strength fasteners or springs plated without a baking step
- Aerospace, automotive safety or medical parts in the work mix
- Embrittlement relief bake logged for every hardened steel lot
- Thickness, adhesion and salt-spray tests recorded against each job
- Customer specifications reviewed and signed off before processing
Workers’ injury
HighOperators work over hot acids, caustics, cyanide and chromium solutions on wet floors, lifting racks and barrels by hand.
Injuries and illness to employees.
- Hand-carried racks over open tanks instead of hoists
- Hexavalent chromium or cadmium lines with weak local exhaust
- No eyewash or shower within seconds of the tanks
- Local exhaust on every fuming tank, with airflow measured regularly
- Face shields, aprons and gloves matched to each chemical
- Air and medical monitoring for chromium, cadmium, nickel and cyanide
Commercial auto
ModerateLight trucks collect and return customers' parts, and some shops haul chemicals or waste.
Owned, hired and employee-driven vehicles, deliveries, customers’ vehicles in care.
- Drivers carrying drums of chemicals or sludge in open trucks
- Daily pickup routes across a wide radius
- Driving record checks and secured, labeled loads
- Licensed haulers used for all hazardous waste
Crime and theft
ModerateGold, silver, palladium and rhodium salts and anodes are compact, valuable and easy to carry out.
Burglary, robbery, employee dishonesty, cash, payment and invoice fraud.
- Precious metal plating with no usage reconciliation
- Copper and nickel anodes stored in an unlocked yard
- Precious metals in a safe, issued and weighed by two people
- Monitored alarm and cameras covering chemical and anode stores
Inland marine and equipment
ElevatedEverything on the line belongs to customers, and a bad bath or fire can ruin a whole batch of machined parts.
Property in transit, at job sites or in the insured’s care, and mobile equipment.
- High-value aerospace or tooling components held for days
- No stated limit of liability on work orders
- Bailee cover sized to peak values of customers' parts
- Incoming count and condition recorded for every lot
Environmental
HighCyanide, hexavalent chromium, cadmium, nickel and acids pass through floor trenches, sumps and wastewater treatment every working day.
Pollution on or from the site or the work.
- Cracked or uncoated concrete under tanks and in trenches
- Older site with past degreasing using chlorinated solvents
- Sludge drums accumulating beyond permitted storage time
- Sealed, bermed containment under every tank with leak detection
- Treatment plant with continuous pH and metals monitoring before discharge
- Baseline soil and groundwater study before binding
Cyber and data
ModerateJob travelers, customer drawings and rectifier controls sit on a small network; ransomware delays work but little personal data is held.
Data breaches, ransomware, system outages and attacks on connected equipment.
- Aerospace or defense customers requiring controlled handling of technical data
- Line controllers and wastewater monitoring reachable over the internet
- Offline backups of job records, specifications and certifications
- Process controllers on a separate network with no direct remote access
Professional liability
ModerateShops issue certificates of conformance and test results that customers rely on to release parts without inspecting them again.
Loss or injury caused by advice, design, testing, care or another professional service.
- Certificates signed before thickness or adhesion tests are complete
- In-house lab testing parts for other shops as a paid service
- Certificates generated only from recorded test data and checked by a second person
- Test equipment calibrated on schedule with records kept
Umbrella and excess
ElevatedA cyanide or acid gas release reaching neighbors, or embrittled fasteners failing in aircraft or vehicles, can exceed primary limits.
How likely one liability event is to exhaust primary limits.
- Cyanide lines in dense mixed-use or residential surroundings
- Plating of flight-critical or automotive safety fasteners
- Acids kept physically apart from cyanide baths and their drains
- Contract terms limiting liability to rework or replacement of parts
Construction, occupancy, protection, exposure.
What a risk engineer expects to find at a typical site of this type, and what to compare a submission against.
- Construction
- Older single-story masonry or steel buildings, often with roof decks and steel corroded by acid fumes, plastic ductwork overhead and process pits cut into the floor.
- Occupancy
- Rows of heated plastic tanks holding acids, caustics, cyanide and metal salts, high-current rectifiers, buffing dust, solvent degreasing and a wastewater treatment room.
- Protection
- Sprinklers inside plastic ducts and scrubbers as well as over the lines, low-level heater cutoffs, curbed and segregated chemical rooms, and monitored alarms for unattended hours.
- Exposure
- Often in older industrial districts beside homes or other small shops, where a fume release, fire runoff or spill reaches neighbors, storm drains and the sewer quickly.
What to ask and look for.
Start with the desk review before quoting, then walk the site. Tick questions off as you go; ticks are kept in this browser only.
Before quoting: ask the broker or owner
Documents to request
On site: processes and chemicals
On site: building and protection
On site: containment and waste
On site: line operators
Refer or decline if you find
- Immersion heaters in plastic tanks with no low-level cutoff
- Stained, cracked floors or trenches with no containment beneath tanks
- Cyanide and acid containers stored together
- Repeated wastewater discharge violations or an open cleanup order
- Heavily corroded sprinkler piping and electrical panels above the lines
How UrbanStat data helps.
Floodwater that overtops open tanks carries cyanide and metals off site, turning a property loss into a pollution claim. Earthquake sloshes and cracks tanks. Wind damage to roofs and scrubber stacks lets rain into the baths.
- Flood scores at the address show whether open process tanks and chemical stores sit where rising water would carry their contents off site.
- Parcel and permit data give the construction date and permit history, a quick check on the building's age and on when process lines or ventilation were altered.
- Earthquake scores for the site inform terms where rows of liquid-filled tanks and overhead plastic ductwork would spill or collapse in strong shaking.
What the published numbers say.
Official statistics for the industry or property type closest to this business. They describe the industry as a whole, not any one insured.
4.1 recordable injuries and illnesses per 100 full-time workers, above the private-industry average of 2.3.
1.3 of these cases per 100 workers involved days away from work.
United States, 2024. Industry: Electroplating, plating, polishing, anodizing, and coloring (NAICS 332813). Source: U.S. Bureau of Labor Statistics, Survey of Occupational Injuries and Illnesses, Table 1: incidence rates of nonfatal occupational injuries and illnesses by industry and case types, 2024.
7 fatal work injuries in 2024.
Deaths per 100,000 full-time equivalent workers, for the industry sector as a whole.
United States, private industry, 2024. Industry: Coating, Engraving, Heat Treating, and Allied Activities (NAICS 33281), the closest published group. Source: U.S. Bureau of Labor Statistics, Census of Fatal Occupational Injuries; sector rates.
304 citations from 78 inspections; 71% were classed serious, willful or repeat.
- 1910.134 Respiratory protection37
- 1910.1200 Hazard communication23
- 1910.305 Wiring methods, components, and equipment for general use19
- 1910.1026 Chromium (VI)18
- 1910.132 General requirements (personal protective equipment)16
Standards cited most often in this industry, by number of citations.
United States, citations issued October 2024 to September 2025 (federal fiscal year 2025). Industry: Electroplating, Plating, Polishing, Anodizing, and Coloring (NAICS 332813). Covers federal and state-plan inspections. A citation is one violation item; one inspection can produce several. Source: U.S. Department of Labor, Occupational Safety and Health Administration, OSHA enforcement data (inspections and violations); standard titles from the Code of Federal Regulations, Title 29 (section headings).
7,966 fires a year reported in industrial and manufacturing properties, causing about $810 million in direct property damage a year.
United States, 2020 to 2024, annual average. The group includes utility, defense, agriculture and mining properties. Source: National Fire Protection Association, Structure Fires in Industrial and Manufacturing Properties.
434 facilities reported toxic chemical releases totaling 9.3 million pounds on and off site.
- Zinc compounds3.6M
- Nitrate compounds1.5M
- Chromium and chromium compounds778,336
Chemicals released in the largest amounts, in pounds. 198 of the facilities reported at least one chemical classed as a carcinogen.
United States, 2024. Industry: Electroplating, Plating, Polishing, Anodizing, and Coloring (NAICS 332813). Covers facilities in listed industries with ten or more full-time employees that handle listed chemicals above set thresholds. Source: U.S. Environmental Protection Agency, Toxics Release Inventory basic data files.
Industry loss ratios by line2020 to 2024, the same table on every guide
Loss ratios are published by line of insurance, not by business type. They show how each line has run for insurers as a whole, whatever the business insured.
| Published line | Closest line in this guide | 2020 | 2021 | 2022 | 2023 | 2024 |
|---|---|---|---|---|---|---|
| Fire | Property | 63.2% | 67.3% | 62.4% | 45.5% | 40.9% |
| Commercial multiple peril | Property and liability sold as a package | 61.2% | 60.2% | 59.4% | 61.2% | 54.4% |
| Inland marine | Inland marine and equipment | 64.5% | 49.4% | 47.1% | 44.1% | 44.0% |
| Other liability | Premises liability, and most umbrella, professional (other than medical) and cyber cover | 65.1% | 58.8% | 61.0% | 63.7% | 71.2% |
| Products liability | Products and completed work | 48.2% | 52.2% | 46.0% | 57.5% | 60.3% |
| Workers’ compensation | Workers’ injury | 47.9% | 49.2% | 45.0% | 44.3% | 46.0% |
| Commercial auto liability | Commercial auto | 68.3% | 66.5% | 71.9% | 76.8% | 77.6% |
| Commercial auto physical damage | Commercial auto | 50.9% | 56.3% | 64.3% | 65.1% | 57.9% |
United States. Losses incurred as a percent of direct premiums earned, countrywide, before reinsurance and not including loss adjustment expense. Source: National Association of Insurance Commissioners, Report on Profitability by Line by State in 2024, ten-year summary.
- Pollution legal liability
- General liability pollution exclusions leave gradual soil and groundwater contamination under tanks and trenches uninsured.
- Equipment breakdown
- Rectifiers, scrubber fans and treatment pumps fail electrically and stop every line without any fire.
- Transportation pollution
- Spent baths and sludge carried on the shop's own trucks can spill on public roads, outside site pollution cover.
- Rework and recall expense
- Faulty plating found after assembly forces customers to strip, replate or replace parts, and they bill the shop.
See this risk on the map.
Book a 30-minute walkthrough tailored to your portfolio and perils of interest.