Contact lens manufacturers

Contact lens manufacturers cast-mold or lathe-cut lenses from hydrogel and silicone polymers in clean rooms, then hydrate, sterilize and blister-pack them in saline. A lens sits on the eye, so a sterility or dimensional failure across one lot can injure many wearers and force a recall.

Manufacturing · NAICS 339115 · SIC 3851 · Updated November 2026

01 / Loss drivers

Where losses come from.

  1. 01

    Contaminated or out-of-specification lots causing eye infections and recalls

  2. 02

    Smoke, water or power loss contaminating clean rooms and work in progress

  3. 03

    Long shutdowns while damaged lines are rebuilt and revalidated

How it comparesEach line’s rating against the average for its NAICS sector, Manufacturing (178 business types), and for all 747.
  1. PropertyProperty: Elevated, 3 of 5; sector average 3.7; all business types 2.9.
  2. Business interruptionBusiness interruption: High, 4 of 5; sector average 3.5; all business types 2.7.
  3. Premises liabilityPremises liability: Low, 1 of 5; sector average 1.9; all business types 2.7.
  4. Products and completed workProducts and completed work: High, 4 of 5; sector average 3.4; all business types 2.6.
  5. Workers’ injuryWorkers’ injury: Moderate, 2 of 5; sector average 3.4; all business types 3.0.
  6. Commercial autoCommercial auto: Low, 1 of 5; sector average 2.3; all business types 2.5.
  7. Crime and theftCrime and theft: Moderate, 2 of 5; sector average 1.9; all business types 2.2.
  8. Inland marine and equipmentInland marine and equipment: Moderate, 2 of 5; sector average 2.6; all business types 2.6.
  9. EnvironmentalEnvironmental: Elevated, 3 of 5; sector average 2.8; all business types 2.3.
  10. Cyber and dataCyber and data: Elevated, 3 of 5; sector average 2.7; all business types 2.7.
  11. Professional liabilityProfessional liability: Moderate, 2 of 5; sector average 1.5; all business types 2.0.
  12. Umbrella and excessUmbrella and excess: High, 4 of 5; sector average 3.6; all business types 3.6.
What’s changing
  • Daily disposables and silicone hydrogel materials push volumes higher, so one plant ships far more lenses and a single bad lot reaches more wearers.
  • Myopia-control lenses for children and drug-releasing lenses bring younger and more vulnerable wearers, widening the products exposure and the regulatory scrutiny.
  • Online subscriptions and direct shipping to wearers add prescription verification duties, personal health data and parcel volumes that practitioner-led channels did not carry.
02 / Line by line

Twelve lines, rated.

Each line shows its rating and the reason for it; open a line for what to watch for and the controls that matter. Ratings are UrbanStat’s own editorial view of a typical business of this type, on a five-step scale. They are a starting point for questions, not a quote, a rate or a statistical measure.

Property

Elevated
Flammable monomers and extraction solvents feed a fire, and even light smoke or water condemns clean rooms and stock.

Fire, explosion, water and weather damage to buildings, contents and stock.

Watch for
  • Solvent extraction baths or monomer mixing outside rated rooms
  • Plastic-lined clean rooms and ducts with no sprinklers inside
  • Injection molding of plastic lens molds beside cartoned stock
Controls that matter
  • Sprinklers in clean rooms, ducts and above ceilings
  • Monomer and solvent rooms with ventilation, containment and grounding
  • Very early smoke detection in process and plant rooms

Business interruption

High
Validated molding and sterilizing lines are custom-built, and regulators must approve them again before product ships.

How long and how costly a shutdown is.

Watch for
  • One site making every product line
  • Sole-source polymer or blister foil suppliers
  • No standby power for clean-room air handling and autoclaves
Controls that matter
  • Finished stock held at a separate distribution site
  • Second validated line or site for key products
  • Standby generation tested under load

Premises liability

Low
Controlled-entry plants admit only staff, auditors and service engineers.

Injuries to customers and the public, on site or caused by operations elsewhere.

Watch for
  • Contractors working in plant rooms without induction
Controls that matter
  • Permit-to-work system for all outside contractors

Products and completed work

High
A regulated medical device worn on the cornea: microbial contamination, residual chemicals or wrong parameters damage sight.

Harm caused by what the business sells, serves, makes, installs or repairs.

Watch for
  • Cosmetic colored lenses sold without prescription through online channels
  • Extended-wear and overnight lenses with higher infection rates
  • Contract manufacturing under other labels without clear liability terms
Controls that matter
  • Validated sterilization with every cycle recorded and released by quality staff
  • Lot traceability to the prescriber and a tested recall procedure
  • Complaint trending reported to the regulator as required

Workers’ injury

Moderate
Clean, largely automated work; exposures are sensitizing monomers, solvents, autoclave burns and repetitive inspection.

Injuries and illness to employees.

Watch for
  • Skin contact with uncured acrylate monomers
  • Manual lens inspection under magnification for whole shifts
Controls that matter
  • Closed dosing and gloves rated for acrylates
  • Automated inspection or frequent rotation at inspection stations

Commercial auto

Low
Product ships by courier; there is no fleet.

Owned, hired and employee-driven vehicles, deliveries, customers’ vehicles in care.

Watch for
  • Sales representatives covering large territories by car
Controls that matter
  • Driving record checks for sales staff

Crime and theft

Moderate
Small, light, branded product resells easily through gray-market online channels.

Burglary, robbery, employee dishonesty, cash, payment and invoice fraud.

Watch for
  • Rejected or expired lenses leaving through waste streams
Controls that matter
  • Destruction of rejects witnessed and recorded

Inland marine and equipment

Moderate
High values move in small parcels to distributors, practitioners and wearers' homes, and export consignments sit in transit for weeks.

Property in transit, at job sites or in the insured’s care, and mobile equipment.

Watch for
  • Export shipments consolidated into a few high-value consignments
Controls that matter
  • Transit limits and carrier terms reviewed against peak shipment values

Environmental

Elevated
Acrylate monomers, isopropanol and other extraction solvents, and process wastewater need managed storage and treatment.

Pollution on or from the site or the work.

Watch for
  • Bulk solvent tanks or drum stores without containment
  • Wastewater discharged without monitoring
Controls that matter
  • Solvent recovery with diked storage
  • Discharge permits with sampling records kept

Cyber and data

Elevated
Lens parameters, lot release data and practitioner ordering portals run on networks; ransomware halts validated lines and prescription fulfillment.

Data breaches, ransomware, system outages and attacks on connected equipment.

Watch for
  • Direct-to-wearer web sales holding prescription and payment details
  • Molding and inspection equipment on the same network as office systems
Controls that matter
  • Production network segmented from office and internet-facing systems
  • Offline, tested backups of batch records and lens design files

Professional liability

Moderate
Specialty labs design custom lenses from practitioners' measurements and advise on fitting; mass-market lines sell no advice.

Loss or injury caused by advice, design, testing, care or another professional service.

Watch for
  • Fitting consultations or design software supplied to eye care practitioners
Controls that matter
  • Written terms making the prescriber responsible for fit and patient selection

Umbrella and excess

High
One contaminated or out-of-specification lot reaches many wearers at once, and corneal infections that cost sight bring large awards.

How likely one liability event is to exhaust primary limits.

Watch for
  • Large private-label lots distributed across several markets
  • Lens care solutions or drug-releasing lenses added to the range
Controls that matter
  • Lot sizes and traceability that confine a recall to defined batches
  • Adverse event trends reviewed by quality staff every month
03 / Property picture

Construction, occupancy, protection, exposure.

What a risk engineer expects to find at a typical site of this type, and what to compare a submission against.

Construction
Modern single-story steel or concrete plants with clean rooms built from insulated panels, sometimes with combustible cores, service voids above ceilings, and air handling plant on the roof.
Occupancy
Monomer mixing, injection molding of lens molds, curing, solvent or water extraction, hydration and autoclaving, then blister packing and cartoning in high volume.
Protection
Sprinklers in clean rooms, ceiling voids and warehouses, very early smoke detection, ventilated and diked monomer and solvent rooms, and standby power for air handling and sterilizers.
Exposure
Industrial park neighbors with dusty or smoky processes threaten clean-room air, and a regional power outage or water main break stops production even without damage.
04 / Checklist

What to ask and look for.

Start with the desk review before quoting, then walk the site. Tick questions off as you go; ticks are kept in this browser only.

Before quoting: ask the broker or owner

Documents to request

On site: products and quality

On site: plant and utilities

On site: continuity and records

Refer or decline if you find

  • Sterilization records incomplete or released without quality review
  • Open regulatory warning or import alert
  • Flammable solvent processes inside unsprinklered clean rooms
  • All production and finished stock at one address
05 / Location

How UrbanStat data helps.

Clean rooms tolerate no water, dust or long power outages, so flood, wind-driven rain and earthquake damage to ducts and utilities stop production well beyond the physical repair time. Revalidation follows every restart.

FloodEarthquakeHurricaneWind
  • Flood and earthquake scores at the address show how exposed clean rooms and validated lines are before interruption limits and indemnity periods are agreed.
  • Live event overlays show whether a hurricane track or wildfire perimeter threatens the single plant that supplies an insured's whole product range.
  • More than 300 data points per property, including construction date and permit history, help confirm the building details behind a high-value clean-room submission.
Flood · Earthquake · Hurricane · Wind
06 / Public loss data

What the published numbers say.

Official statistics for the industry or property type closest to this business. They describe the industry as a whole, not any one insured.

Workers’ injury frequency

1.5 recordable injuries and illnesses per 100 full-time workers, below the private-industry average of 2.3.

Medical equipment and supplies manufacturing
1.5
All private industry
2.3

0.3 of these cases per 100 workers involved days away from work.

United States, 2024. Industry: Medical equipment and supplies manufacturing (NAICS 33911), the closest published group. Source: U.S. Bureau of Labor Statistics, Survey of Occupational Injuries and Illnesses, Table 1: incidence rates of nonfatal occupational injuries and illnesses by industry and case types, 2024.

Workplace deaths

4 fatal work injuries in 2024.

Manufacturing
2.4
All workers
3.3

Deaths per 100,000 full-time equivalent workers, for the industry sector as a whole.

United States, private industry, 2024. Industry: Medical Equipment and Supplies Manufacturing (NAICS 33911), the closest published group. Source: U.S. Bureau of Labor Statistics, Census of Fatal Occupational Injuries; sector rates.

Most cited safety standards

14 citations from 4 inspections; 64% were classed serious, willful or repeat.

  • 1910.1200 Hazard communication
    3
  • 1910.132 General requirements (personal protective equipment)
    1
  • 1910.133 Eye and face protection
    1
  • 1910.138 Hand protection
    1
  • 1910.305 Wiring methods, components, and equipment for general use
    1

Standards cited most often in this industry, by number of citations.

United States, citations issued October 2024 to September 2025 (federal fiscal year 2025). Industry: Ophthalmic Goods Manufacturing (NAICS 339115). Covers federal and state-plan inspections. A citation is one violation item; one inspection can produce several. Source: U.S. Department of Labor, Occupational Safety and Health Administration, OSHA enforcement data (inspections and violations); standard titles from the Code of Federal Regulations, Title 29 (section headings).

Fire frequency

7,966 fires a year reported in industrial and manufacturing properties, causing about $810 million in direct property damage a year.

United States, 2020 to 2024, annual average. The group includes utility, defense, agriculture and mining properties. Source: National Fire Protection Association, Structure Fires in Industrial and Manufacturing Properties.

Toxic chemical releases

17 facilities reported toxic chemical releases totaling 37,451 pounds on and off site.

  • N-butyl alcohol
    13,175
  • Methanol
    12,445
  • Lead
    5,968

Chemicals released in the largest amounts, in pounds. 12 of the facilities reported at least one chemical classed as a carcinogen.

United States, 2024. Industry: Ophthalmic Goods Manufacturing (NAICS 339115). Covers facilities in listed industries with ten or more full-time employees that handle listed chemicals above set thresholds. Source: U.S. Environmental Protection Agency, Toxics Release Inventory basic data files.

Industry loss ratios by line2020 to 2024, the same table on every guide

Loss ratios are published by line of insurance, not by business type. They show how each line has run for insurers as a whole, whatever the business insured.

Published lineClosest line in this guide20202021202220232024
FireProperty63.2%67.3%62.4%45.5%40.9%
Commercial multiple perilProperty and liability sold as a package61.2%60.2%59.4%61.2%54.4%
Inland marineInland marine and equipment64.5%49.4%47.1%44.1%44.0%
Other liabilityPremises liability, and most umbrella, professional (other than medical) and cyber cover65.1%58.8%61.0%63.7%71.2%
Products liabilityProducts and completed work48.2%52.2%46.0%57.5%60.3%
Workers’ compensationWorkers’ injury47.9%49.2%45.0%44.3%46.0%
Commercial auto liabilityCommercial auto68.3%66.5%71.9%76.8%77.6%
Commercial auto physical damageCommercial auto50.9%56.3%64.3%65.1%57.9%

United States. Losses incurred as a percent of direct premiums earned, countrywide, before reinsurance and not including loss adjustment expense. Source: National Association of Insurance Commissioners, Report on Profitability by Line by State in 2024, ten-year summary.

Coverages to raise
Product recall expense
A sterility failure in one lot means tracing and pulling lenses from practitioners, retailers and wearers across markets.
Equipment breakdown
Molding presses, autoclaves and clean-room air handlers fail without fire, and each restart needs revalidation.
Contingent business interruption
Lens polymers, mold resins and blister foil often come from one qualified supplier that is slow to replace.
Clinical trials liability
New materials and designs are tested on volunteers' eyes before approval, an exposure product cover may exclude.
Classification
SystemCodeIndustry
NAICS 2022, primary339115Ophthalmic Goods Manufacturing
SIC 1987, primary3851Ophthalmic Goods
Next step

See this risk on the map.

Book a 30-minute walkthrough tailored to your portfolio and perils of interest.

Request a Demo →