Steel mills
Steel mills melt scrap or reduce iron ore, refine and cast the liquid steel, then roll it into plate, coil, bar and sections; re-rollers and pipe and tube mills work purchased steel. Huge volumes of molten metal, high-voltage furnaces, large hydraulic systems and overhead cranes make losses infrequent but very large.
Where losses come from.
- 01
Molten metal breakouts and steam explosions at furnaces, ladles and casters
- 02
Hydraulic oil, transformer and cable fires in rolling mills and electrical rooms
- 03
Fatal and disabling injuries from cranes, hot metal, gas and moving stock
- PropertyProperty: High, 4 of 5; sector average 3.7; all business types 2.9.
- Business interruptionBusiness interruption: Severe, 5 of 5; sector average 3.5; all business types 2.7.
- Premises liabilityPremises liability: Moderate, 2 of 5; sector average 1.9; all business types 2.7.
- Products and completed workProducts and completed work: Elevated, 3 of 5; sector average 3.4; all business types 2.6.
- Workers’ injuryWorkers’ injury: High, 4 of 5; sector average 3.4; all business types 3.0.
- Commercial autoCommercial auto: Elevated, 3 of 5; sector average 2.3; all business types 2.5.
- Crime and theftCrime and theft: Moderate, 2 of 5; sector average 1.9; all business types 2.2.
- Inland marine and equipmentInland marine and equipment: Elevated, 3 of 5; sector average 2.6; all business types 2.6.
- EnvironmentalEnvironmental: High, 4 of 5; sector average 2.8; all business types 2.3.
- Cyber and dataCyber and data: Elevated, 3 of 5; sector average 2.7; all business types 2.7.
- Professional liabilityProfessional liability: Low, 1 of 5; sector average 1.5; all business types 2.0.
- Umbrella and excessUmbrella and excess: High, 4 of 5; sector average 3.6; all business types 3.6.
- Electric arc furnaces fed with scrap and direct-reduced iron are replacing blast furnaces, concentrating risk in transformers, power supply and scrap screening.
- Hydrogen-based iron reduction and carbon capture projects bring new gas hazards and expensive, first-of-a-kind equipment with uncertain replacement times.
- Scrap streams contain more lithium-ion batteries, sealed cylinders and mixed alloys, raising explosion risk at charging and demanding tighter grade control.
Twelve lines, rated.
Each line shows its rating and the reason for it; open a line for what to watch for and the controls that matter. Ratings are UrbanStat’s own editorial view of a typical business of this type, on a five-step scale. They are a starting point for questions, not a quote, a rate or a statistical measure.
Property
HighLiquid steel, furnace transformers, oil-filled hydraulics and cable tunnels sit together; one breakout or oil fire damages very costly plant.
Fire, explosion, water and weather damage to buildings, contents and stock.
- Water leaks from furnace panels or lances into the melt
- Wet or sealed scrap charged without screening
- Unprotected hydraulic cellars, cable tunnels and cold mill rolling-oil exhaust ducts
- Leak detection on water-cooled panels with emergency furnace procedures
- Fixed fire protection for hydraulic rooms, transformers and cable tunnels
- Breakout detection on casters and containment pits kept dry
Business interruption
SevereMelt shop, caster and hot mill run in series; losing a furnace transformer or mill drive stops everything for months.
How long and how costly a shutdown is.
- Single furnace or single caster with no bypass route
- No spare furnace transformer or main mill motor
- Customers in vehicle or appliance supply chains with penalty clauses
- Critical spares on site, tested and ready to install
- Ability to buy slab or billet and keep rolling
- Condition monitoring of transformers, gearboxes and crane hoists
Premises liability
ModerateSites are fenced and remote from the public, but large numbers of contractors, haulers and rail crews work inside.
Injuries to customers and the public, on site or caused by operations elsewhere.
- Major shutdown work by outside contractors
- Slag or dust nuisance reaching neighbors
- Contractor prequalification, induction and permit-to-work systems
- Indemnity and insurance terms in all service contracts
Products and completed work
ElevatedSteel goes into structures, pressure equipment and vehicles; off-grade heats are usually caught, but a miss spreads widely.
Harm caused by what the business sells, serves, makes, installs or repairs.
- Plate, pipe or bar sold for pressure, rail or safety-critical uses
- Mill certificates issued by the same team that ships the product
- Radioactive sources melted from scrap
- Heat-by-heat chemistry and mechanical testing with full traceability
- Independent sign-off of test certificates
- Radiation portals on every inbound scrap load
Workers’ injury
HighFewer workers than in the past, but the hazards are lethal: ladle cranes, liquid metal, carbon monoxide, hot coil and rail movements.
Injuries and illness to employees.
- People on foot in crane bays and scrap yards
- Maintenance inside furnaces, ducts and gas lines
- Long shifts and heat exposure in the melt shop
- Exclusion zones and remote operation at tapping and casting
- Gas monitoring, lockout and confined space permits
- Crane inspection and certified operators for hot metal lifts
Commercial auto
ElevatedScrap arrives and product leaves by heavy truck and rail; mills often own shuttle trucks and locomotives.
Owned, hired and employee-driven vehicles, deliveries, customers’ vehicles in care.
- Own fleet hauling coil or long products on public roads
- Internal haul vehicles crossing public roads
- Coil and bundle securing rules enforced at the gate
- Driver qualification and maintenance records for owned trucks
Crime and theft
ModerateAlloying metals, copper and electrodes are valuable, and scrap buying invites weight and grade fraud.
Burglary, robbery, employee dishonesty, cash, payment and invoice fraud.
- Nickel, molybdenum and other alloys stored without stock control
- Scrap graded and paid by the same person
- Locked alloy stores with reconciled usage
- Segregated weighing, grading and payment for scrap
Inland marine and equipment
ElevatedSlag pot carriers, loaders, locomotives and mobile cranes are large values, and product moves by rail, barge and ship.
Property in transit, at job sites or in the insured’s care, and mobile equipment.
- Mobile equipment working around hot slag
- Export cargoes and stock at outside processors
- Fire suppression on mobile plant in hot areas
- Cargo and off-site stock declared and tracked
Environmental
HighFurnace dust is a hazardous waste, and slag, mill scale, pickling acid, oils and cooling water all need managed disposal.
Pollution on or from the site or the work.
- Furnace dust stored outdoors or landfilled on site
- Acid pickling lines and old lagoons
- Long industrial history on the same land
- Baghouses with dust sent to licensed recycling
- Acid regeneration and treated, recirculated process water
- Groundwater monitoring and diked oil storage
Cyber and data
ElevatedFurnace, caster and mill automation run on networked controls; an attack mid-heat can force an unsafe stop and weeks of downtime.
Data breaches, ransomware, system outages and attacks on connected equipment.
- Control systems reachable from office networks or vendor remote access
- Unsupported operating systems on furnace and mill controllers
- Segmented control networks with monitored vendor access
- Offline backups of control logic and a tested safe shutdown
Professional liability
LowLittle advice is sold; grade selection and metallurgical support for customers come with the steel.
Loss or injury caused by advice, design, testing, care or another professional service.
- Metallurgical testing or consulting sold to outside clients
- Sales terms disclaiming advice beyond the stated grade and specification
Umbrella and excess
HighA breakout or explosion during a contractor shutdown, a coil falling from a truck or a gas release can injure many.
How likely one liability event is to exhaust primary limits.
- Shutdowns with large contractor crews near hot metal and cranes
- Fuel gas lines and holders near the site boundary
- Contractor permit system enforced through every outage
- Gas detection and emergency plans shared with neighbors
Construction, occupancy, protection, exposure.
What a risk engineer expects to find at a typical site of this type, and what to compare a submission against.
- Construction
- Very large steel-frame melt shops and rolling mill halls with crane runways, below-grade pits and hydraulic cellars, long cable tunnels and older roofs with combustible insulation.
- Occupancy
- Liquid steel in furnaces, ladles and casters beside water cooling, high-voltage furnace transformers, oil-filled hydraulics and lubrication systems, fuel gases, and hot coil and bar.
- Protection
- Fixed protection in hydraulic cellars, cable tunnels and transformer bays, dry breakout pits, water leak detection on furnaces, a site fire brigade and a reliable fire water supply.
- Exposure
- Mills sit on large industrial sites by rivers, harbors and rail, often beside processors, slag handlers and gas plants that add fire and explosion exposure.
What to ask and look for.
Start with the desk review before quoting, then walk the site. Tick questions off as you go; ticks are kept in this browser only.
Before quoting: ask the broker or owner
Documents to request
On site: melt shop and casting
On site: mills and electrical
On site: continuity
On site: people and environment
Refer or decline if you find
- No spare furnace transformer and no sourcing plan
- Hydraulic cellars and cable tunnels without fixed protection
- Scrap charged without moisture or radiation checks
- Recent breakout or steam explosion with causes unresolved
How UrbanStat data helps.
Mills sit beside rivers and harbors for water and transport, so flood and surge threaten pits, cellars and furnaces holding liquid metal. Tall crane buildings and stacks are exposed to wind and shaking.
- Flood and storm surge scores at the address show whether water could reach furnace pits and hydraulic cellars at waterside mills.
- Street-by-street exposure views show how much insured value sits at the mill and the processors and suppliers clustered around it, with alerts when a threshold is passed.
- Live event overlays show whether a mill lies in a hurricane's forecast track, where an orderly shutdown takes time and a forced one damages plant.
What the published numbers say.
Official statistics for the industry or property type closest to this business. They describe the industry as a whole, not any one insured.
1.9 recordable injuries and illnesses per 100 full-time workers, close to the private-industry average of 2.3.
0.6 of these cases per 100 workers involved days away from work.
United States, 2024. Industry: Iron and steel mills and ferroalloy manufacturing (NAICS 3311), the closest published group. Source: U.S. Bureau of Labor Statistics, Survey of Occupational Injuries and Illnesses, Table 1: incidence rates of nonfatal occupational injuries and illnesses by industry and case types, 2024.
15 fatal work injuries in 2024, most often from contact with objects and equipment (6).
Deaths per 100,000 full-time equivalent workers, for the industry sector as a whole.
United States, private industry, 2024. Industry: Primary Metal Manufacturing (NAICS 331), the closest published group. Source: U.S. Bureau of Labor Statistics, Census of Fatal Occupational Injuries; sector rates.
109 citations from 45 inspections; 54% were classed serious, willful or repeat.
- 1910.147 The control of hazardous energy (lockout/tagout)17
- 1910.303 General (electrical)12
- 1910.305 Wiring methods, components, and equipment for general use7
- 1910.1200 Hazard communication6
- 1910.134 Respiratory protection6
Standards cited most often in this industry, by number of citations.
United States, citations issued October 2024 to September 2025 (federal fiscal year 2025). Industry: Iron and Steel Mills and Ferroalloy Manufacturing (NAICS 331110). Covers federal and state-plan inspections. A citation is one violation item; one inspection can produce several. Source: U.S. Department of Labor, Occupational Safety and Health Administration, OSHA enforcement data (inspections and violations); standard titles from the Code of Federal Regulations, Title 29 (section headings).
7,966 fires a year reported in industrial and manufacturing properties, causing about $810 million in direct property damage a year.
United States, 2020 to 2024, annual average. The group includes utility, defense, agriculture and mining properties. Source: National Fire Protection Association, Structure Fires in Industrial and Manufacturing Properties.
137 facilities reported toxic chemical releases totaling 117.4 million pounds on and off site.
- Zinc compounds37.2M
- Manganese and manganese compounds30.5M
- Nitrate compounds14.6M
Chemicals released in the largest amounts, in pounds. 127 of the facilities reported at least one chemical classed as a carcinogen.
United States, 2024. Industry: Iron and Steel Mills and Ferroalloy Manufacturing (NAICS 331110). Covers facilities in listed industries with ten or more full-time employees that handle listed chemicals above set thresholds. Source: U.S. Environmental Protection Agency, Toxics Release Inventory basic data files.
Industry loss ratios by line2020 to 2024, the same table on every guide
Loss ratios are published by line of insurance, not by business type. They show how each line has run for insurers as a whole, whatever the business insured.
| Published line | Closest line in this guide | 2020 | 2021 | 2022 | 2023 | 2024 |
|---|---|---|---|---|---|---|
| Fire | Property | 63.2% | 67.3% | 62.4% | 45.5% | 40.9% |
| Commercial multiple peril | Property and liability sold as a package | 61.2% | 60.2% | 59.4% | 61.2% | 54.4% |
| Inland marine | Inland marine and equipment | 64.5% | 49.4% | 47.1% | 44.1% | 44.0% |
| Other liability | Premises liability, and most umbrella, professional (other than medical) and cyber cover | 65.1% | 58.8% | 61.0% | 63.7% | 71.2% |
| Products liability | Products and completed work | 48.2% | 52.2% | 46.0% | 57.5% | 60.3% |
| Workers’ compensation | Workers’ injury | 47.9% | 49.2% | 45.0% | 44.3% | 46.0% |
| Commercial auto liability | Commercial auto | 68.3% | 66.5% | 71.9% | 76.8% | 77.6% |
| Commercial auto physical damage | Commercial auto | 50.9% | 56.3% | 64.3% | 65.1% | 57.9% |
United States. Losses incurred as a percent of direct premiums earned, countrywide, before reinsurance and not including loss adjustment expense. Source: National Association of Insurance Commissioners, Report on Profitability by Line by State in 2024, ten-year summary.
- Equipment breakdown
- Furnace transformers, mill drives and large gearboxes fail without fire, and replacements can take many months.
- Contingent business interruption
- Mills depend on a few suppliers of scrap, ore, electrodes and power, and on large customers.
- Site pollution liability
- Furnace dust, pickling acid, mill scale and old lagoons create pollution claims general liability excludes.
- Product recall
- Off-grade steel built into vehicle, pipeline or pressure parts can force customers to recall and replace finished goods.
- Utility service interruption
- A grid outage off the premises stops arc furnaces at once and can freeze metal in ladles.
| System | Code | Industry |
|---|---|---|
| NAICS 2022, primary | 331110 | Iron and Steel Mills and Ferroalloy Manufacturing |
| NAICS 2022 | 331221 | Rolled Steel Shape Manufacturing |
| NAICS 2022 | 331210 | Iron and Steel Pipe and Tube Manufacturing from Purchased Steel |
| SIC 1987, primary | 3312 | Steel Works, Blast Furnaces |
| SIC 1987 | 3316 | Cold-Rolled Steel Sheet, Strip, and Bars |
| SIC 1987 | 3317 | Steel Pipe and Tubes |
See this risk on the map.
Book a 30-minute walkthrough tailored to your portfolio and perils of interest.