Spray equipment manufacturersNAICS 333912 · SIC 3563
Spray equipment manufacturers build paint sprayers, pressure washers, pesticide and crop sprayers and coating guns for contractors, farms and factories. Their products push fluid through a small tip at very high pressure, so injection injuries, hose bursts and solvent ignition drive the claims.
NAICS 333912 Air and Gas Compressor ManufacturingSIC 3563 Air and Gas CompressorsNAICS 333111 Farm Machinery and Equipment ManufacturingNAICS 333991 Power-Driven Handtool Manufacturing+1 more code
Where losses come from.
- 01
High-pressure fluid injection injuries to users' hands from tips and leaking hoses
- 02
Fires and explosions when flammable liquids are sprayed through ungrounded equipment
- 03
Machining, assembly and pressure-testing injuries in the plant
- PropertyProperty: Elevated, 3 of 5; sector average 3.7; all business types 2.9.
- Business interruptionBusiness interruption: Elevated, 3 of 5; sector average 3.5; all business types 2.7.
- Premises liabilityPremises liability: Low, 1 of 5; sector average 1.9; all business types 2.7.
- Products and completed workProducts and completed work: High, 4 of 5; sector average 3.4; all business types 2.6.
- Workers’ injuryWorkers’ injury: Elevated, 3 of 5; sector average 3.4; all business types 3.0.
- Commercial autoCommercial auto: Moderate, 2 of 5; sector average 2.3; all business types 2.5.
- Crime and theftCrime and theft: Moderate, 2 of 5; sector average 1.9; all business types 2.2.
- Inland marine and equipmentInland marine and equipment: Moderate, 2 of 5; sector average 2.6; all business types 2.6.
- EnvironmentalEnvironmental: Moderate, 2 of 5; sector average 2.8; all business types 2.3.
- Cyber and dataCyber and data: Elevated, 3 of 5; sector average 2.7; all business types 2.7.
- Professional liabilityProfessional liability: Low, 1 of 5; sector average 1.5; all business types 2.0.
- Umbrella and excessUmbrella and excess: Elevated, 3 of 5; sector average 3.6; all business types 3.6.
- Cordless battery sprayers and pressure washers replace corded and gas models, bringing lithium-ion fire risk to the plant, the warehouse and customers' trucks.
- Drone and smart crop sprayers with sensors and automatic rate control move product claims toward software, drift and calibration faults.
- More units are sourced from contract plants abroad and sold online, making it harder to control hose and fitting quality and to reach buyers in a recall.
Twelve lines, rated.
Each line shows its rating and the reason for it; open a line for what to watch for and the controls that matter. Ratings are UrbanStat’s own editorial view of a typical business of this type, on a five-step scale. They are a starting point for questions, not a quote, a rate or a statistical measure.
Property
ElevatedMachining, plastic tank molding, powder coating and test spraying with solvents sit alongside carton and plastic component storage.
Fire, explosion, water and weather damage to buildings, contents and stock.
- Test spraying with flammable liquids outside a ventilated booth
- Rotational or blow molding ovens next to plastic stock
- Lithium-ion packs for cordless sprayers stored in general racking
- Sprinklers designed for plastic components and packaged goods
- Water or high-flash test fluids used wherever possible
- Battery packs in a separated, protected storage area
Business interruption
ElevatedPumps depend on a few precision machines and bought-in engines, motors and seals, and demand peaks in spring.
How long and how costly a shutdown is.
- Single-source engines, electric motors or electronic controls
- One test cell that every unit passes through
- Second sources approved for engines, motors and seals
- Seasonal stock build ahead of the spring peak
Premises liability
LowVisitors are limited to dealers, drivers and occasional training classes held in a demonstration room.
Injuries to customers and the public, on site or caused by operations elsewhere.
- Hands-on contractor training with live spraying
- Supervised demonstrations with guards, eye protection and water-based fluids
Products and completed work
HighFluid at very high pressure pierces skin and looks minor until tissue dies; hoses burst, and solvent vapor ignites from static.
Harm caused by what the business sells, serves, makes, installs or repairs.
- Tip guards and trigger locks that are easy to remove
- Units sold for flammable coatings without grounding provisions
- Agricultural sprayers whose leaks or drift expose operators to pesticide
- Tip guards, trigger locks and pressure relief valves on every unit
- Conductive hoses and grounding instructions for solvent-rated models
- Injection injury warnings on the gun, the manual and the carton
Workers’ injury
ElevatedMachinists and assemblers face cuts, strains and pressure-test failures, with solvent and powder exposure in finishing.
Injuries and illness to employees.
- Pressure testing in the open with no shielding
- Repetitive hand assembly at fixed-height benches
- Enclosed test cells with remote pressurization
- Interlocked enclosures on machining centers and lockout before clearing molding machines
- Adjustable workstations and job rotation on assembly lines
Commercial auto
ModerateSales representatives and field technicians drive to dealers and contractors; freight goes by carrier.
Owned, hired and employee-driven vehicles, deliveries, customers’ vehicles in care.
- Demonstration vans carrying pressurized units and solvents
- Driving record checks and secured loads in demonstration vehicles
Crime and theft
ModerateBoxed sprayers and pressure washers are resaleable tools, attractive to dock thieves and dishonest staff.
Burglary, robbery, employee dishonesty, cash, payment and invoice fraud.
- Finished goods staged on open docks overnight
- Returns and warranty units with loose tracking
- Serial-number tracking from assembly to shipment
- Cameras on docks and locked finished goods cages
Inland marine and equipment
ModerateStock moves to distributors by carrier, with demonstration units, show stands and customers' units in for repair.
Property in transit, at job sites or in the insured’s care, and mobile equipment.
- Trailer-mounted rigs taken to shows and field days
- Customers' equipment held for warranty service
- Transit cover sized to a full truckload
- Repair intake logged with condition and value
Environmental
ModerateCutting fluids, paints, test solvents and molding resins are used in modest quantities and are straightforward to contain.
Pollution on or from the site or the work.
- Solvent-laden test fluid drained to floor sumps
- Testing of agricultural units with actual pesticide
- Closed-loop test fluid recovery
- Licensed disposal of spent solvents, coolants and paint waste
Cyber and data
ElevatedApp-connected sprayers, online direct sales and networked machining give attackers both customer data and production systems to disrupt.
Data breaches, ransomware, system outages and attacks on connected equipment.
- Web store or warranty registration holding customer card and contact data
- Agricultural rate controllers and apps updated over the air
- Hosted, tokenized payments and multi-factor access for the web store
- Offline backups and segmented production and test systems
Professional liability
LowEquipment is sold, not advice; spray rate calibration guidance and training classes are the only professional exposure.
Loss or injury caused by advice, design, testing, care or another professional service.
- Calibration or application rate advice given to farm or contractor customers
- Written calibration guides and terms limiting liability for application results
Umbrella and excess
ElevatedInjection injuries cost hands, a solvent vapor explosion can hurt several workers, and gas pressure washers run indoors cause carbon monoxide deaths.
How likely one liability event is to exhaust primary limits.
- Industrial spray systems sold for flammable coatings in enclosed rooms
- Large volumes of consumer units sold through retail chains
- Gas-engine pressure washers without carbon monoxide warnings on the unit
- Grounding, interlock and ventilation guidance built into installation instructions
- Layered limits sized to units in service
Construction, occupancy, protection, exposure.
What a risk engineer expects to find at a typical site of this type, and what to compare a submission against.
- Construction
- Single-story steel or tilt-up concrete plants with a large warehouse section, metal deck roofs and often a separate building for packaged finished goods.
- Occupancy
- Machining of pump parts, plastic tank molding, powder coating, assembly, pressure and spray testing, lithium-ion battery storage, and high racks of boxed finished goods.
- Protection
- Sprinklers designed for plastic components and cartoned stock, enclosed test cells, separated battery and solvent storage, and a monitored alarm with cameras on the docks.
- Exposure
- Industrial park sites with neighbors' trailers and pallets near the walls; a warehouse full of plastics and cartons is also a heavy fire load for nearby buildings.
What to ask and look for.
Start with the desk review before quoting, then walk the site. Tick questions off as you go; ticks are kept in this browser only.
Before quoting: ask the broker or owner
Documents to request
On site: products
On site: plant and protection
On site: people and records
Refer or decline if you find
- High-pressure guns shipped without tip guards or trigger locks
- No injection injury warning on the product itself
- Solvent-rated sprayers with non-conductive hoses
- Imported hoses accepted without burst testing
How UrbanStat data helps.
A single plant and warehouse usually hold all tooling and the season's finished stock. Flood at floor level ruins packaged goods and machine tools, and wind or hail opens lightweight roofs over them.
- Flood scores at the address show whether floor-stacked finished goods and precision machine tools sit in the path of rising water.
- Wind and hail scores for the site inform roof terms for a lightweight building holding the whole season's stock before the spring peak.
- The risk analysis API returns peril scores in seconds, so a plant and its separate warehouse can both be checked inside the quoting workflow.
What the published numbers say.
Official statistics for the industry or property type closest to this business. They describe the industry as a whole, not any one insured.
1.5 recordable injuries and illnesses per 100 full-time workers, below the private-industry average of 2.3.
0.6 of these cases per 100 workers involved days away from work.
United States, 2024. Industry: Air and gas compressor manufacturing (NAICS 333912). Source: U.S. Bureau of Labor Statistics, Survey of Occupational Injuries and Illnesses, Table 1: incidence rates of nonfatal occupational injuries and illnesses by industry and case types, 2024.
4 fatal work injuries in 2024.
Deaths per 100,000 full-time equivalent workers, for the industry sector as a whole.
United States, private industry, 2024. Industry: Other General Purpose Machinery Manufacturing (NAICS 3339), the closest published group. Source: U.S. Bureau of Labor Statistics, Census of Fatal Occupational Injuries; sector rates.
23 citations from 6 inspections; 57% were classed serious, willful or repeat.
- 1910.1200 Hazard communication5
- 1910.305 Wiring methods, components, and equipment for general use2
- 1910.22 General requirements (walking-working surfaces)2
- 1910.95 Occupational noise exposure1
- 1910.179 Overhead and gantry cranes1
Standards cited most often in this industry, by number of citations.
United States, citations issued October 2024 to September 2025 (federal fiscal year 2025). Industry: Air and Gas Compressor Manufacturing (NAICS 333912). Covers federal and state-plan inspections. A citation is one violation item; one inspection can produce several. Source: U.S. Department of Labor, Occupational Safety and Health Administration, OSHA enforcement data (inspections and violations); standard titles from the Code of Federal Regulations, Title 29 (section headings).
7,966 fires a year reported in industrial and manufacturing properties, causing about $810 million in direct property damage a year.
United States, 2020 to 2024, annual average. The group includes utility, defense, agriculture and mining properties. Source: National Fire Protection Association, Structure Fires in Industrial and Manufacturing Properties.
12 facilities reported toxic chemical releases totaling 11,164 pounds on and off site.
- Manganese7,165
- Copper3,792
- Manganese and manganese compounds101
Chemicals released in the largest amounts, in pounds. 8 of the facilities reported at least one chemical classed as a carcinogen.
United States, 2024. Industry: Air and Gas Compressor Manufacturing (NAICS 333912). Covers facilities in listed industries with ten or more full-time employees that handle listed chemicals above set thresholds. Source: U.S. Environmental Protection Agency, Toxics Release Inventory basic data files.
Industry loss ratios by line2020 to 2024, the same table on every guide
Loss ratios are published by line of insurance, not by business type. They show how each line has run for insurers as a whole, whatever the business insured.
| Published line | Closest line in this guide | 2020 | 2021 | 2022 | 2023 | 2024 |
|---|---|---|---|---|---|---|
| Fire | Property | 63.2% | 67.3% | 62.4% | 45.5% | 40.9% |
| Commercial multiple peril | Property and liability sold as a package | 61.2% | 60.2% | 59.4% | 61.2% | 54.4% |
| Inland marine | Inland marine and equipment | 64.5% | 49.4% | 47.1% | 44.1% | 44.0% |
| Other liability | Premises liability, and most umbrella, professional (other than medical) and cyber cover | 65.1% | 58.8% | 61.0% | 63.7% | 71.2% |
| Products liability | Products and completed work | 48.2% | 52.2% | 46.0% | 57.5% | 60.3% |
| Workers’ compensation | Workers’ injury | 47.9% | 49.2% | 45.0% | 44.3% | 46.0% |
| Commercial auto liability | Commercial auto | 68.3% | 66.5% | 71.9% | 76.8% | 77.6% |
| Commercial auto physical damage | Commercial auto | 50.9% | 56.3% | 64.3% | 65.1% | 57.9% |
United States. Losses incurred as a percent of direct premiums earned, countrywide, before reinsurance and not including loss adjustment expense. Source: National Association of Insurance Commissioners, Report on Profitability by Line by State in 2024, ten-year summary.
- Product recall
- Defective guns, hoses or relief valves sold through retail chains are costly to trace and replace.
- Equipment breakdown
- Precision machining centers, molding machines and test rigs fail without fire and halt the spring build.
- Contingent business interruption
- Engines, motors and seals come from a few suppliers whose loss stops assembly before the peak season.
NAICS and SIC codes for spray equipment manufacturers
See this risk on the map.
Book a 30-minute walkthrough tailored to your portfolio and perils of interest.