Sheet metal shops and contractorsNAICS 332322 · SIC 3444

Sheet metal firms cut, bend and join thin steel, aluminum and copper into ductwork, flashings, gutters, enclosures and custom parts, and most install what they make. The shop adds laser and press brake hazards; the field work adds roofs, ladders and torches on other people's buildings.

NAICS 332322 Sheet Metal Work ManufacturingSIC 3444 Sheet Metal WorkNAICS 238220 Plumbing, Heating, and Air-Conditioning ContractorsNAICS 238160 Roofing Contractors+2 more codes

Manufacturing · Updated November 2026

01 / Loss drivers

Where losses come from.

  1. 01

    Falls from roofs, ladders and lifts, and deep cuts from sheet edges

  2. 02

    Fires started by soldering, welding or cutting on customers' buildings

  3. 03

    Leaks, condensation and exhaust duct faults that appear after the job is finished

How it comparesEach line’s rating against the average for its NAICS sector, Manufacturing (178 business types), and for all 747.
  1. PropertyProperty: Moderate, 2 of 5; sector average 3.7; all business types 2.9.
  2. Business interruptionBusiness interruption: Moderate, 2 of 5; sector average 3.5; all business types 2.7.
  3. Premises liabilityPremises liability: Elevated, 3 of 5; sector average 1.9; all business types 2.7.
  4. Products and completed workProducts and completed work: Elevated, 3 of 5; sector average 3.4; all business types 2.6.
  5. Workers’ injuryWorkers’ injury: High, 4 of 5; sector average 3.4; all business types 3.0.
  6. Commercial autoCommercial auto: Elevated, 3 of 5; sector average 2.3; all business types 2.5.
  7. Crime and theftCrime and theft: Moderate, 2 of 5; sector average 1.9; all business types 2.2.
  8. Inland marine and equipmentInland marine and equipment: Elevated, 3 of 5; sector average 2.6; all business types 2.6.
  9. EnvironmentalEnvironmental: Moderate, 2 of 5; sector average 2.8; all business types 2.3.
  10. Cyber and dataCyber and data: Moderate, 2 of 5; sector average 2.7; all business types 2.7.
  11. Professional liabilityProfessional liability: Moderate, 2 of 5; sector average 1.5; all business types 2.0.
  12. Umbrella and excessUmbrella and excess: High, 4 of 5; sector average 3.6; all business types 3.6.
What’s changing
  • Automated coil lines and fiber lasers move more duct fabrication into the shop, cutting field hours but concentrating value in a few machines.
  • Heat pump and energy retrofit work brings crews into occupied older buildings, where concealed asbestos and hot work in voids are common.
  • Metal roofing and cladding demand grows after hail and wind events, putting crews on storm-damaged roofs in unsafe conditions.
02 / Line by line

Twelve lines, rated.

Each line shows its rating and the reason for it; open a line for what to watch for and the controls that matter. Ratings are UrbanStat’s own editorial view of a typical business of this type, on a five-step scale. They are a starting point for questions, not a quote, a rate or a statistical measure.

Property

Moderate
Metal stock and machines are hard to burn; exposure comes from welding, laser cutting, small paint areas and duct insulation.

Fire, explosion, water and weather damage to buildings, contents and stock.

Watch for
  • Laser or plasma cutting tables with poor fume extraction
  • Duct liner, insulation and adhesives stored in bulk
  • Spray painting without a booth
Controls that matter
  • Fume extraction with spark arrestors on laser and plasma tables
  • Duct liner and adhesives stored away from welding and cutting bays
  • Painting confined to a ventilated booth with flammables in a rated cabinet

Business interruption

Moderate
Work can be subcontracted or shifted to hand methods while a laser, shear or brake is repaired.

How long and how costly a shutdown is.

Watch for
  • One coil line or laser handling all duct production
Controls that matter
  • Service contract on key machines and a peer shop for overflow

Premises liability

Elevated
Crews bring torches, long sharp materials and open roof penetrations onto occupied buildings.

Injuries to customers and the public, on site or caused by operations elsewhere.

Watch for
  • Torch soldering of copper or flashing on timber roofs
  • Roof openings left unsealed overnight
  • Material hoisted over entrances and walkways
Controls that matter
  • Hot work permit and fire watch after any open-flame work
  • Temporary weatherproofing at every opening before leaving
  • Exclusion zones below hoisting and roof-edge work

Products and completed work

Elevated
Completed work fails slowly: leaking flashings, sweating ducts, dislodged panels and kitchen exhaust ducts that are not liquid-tight.

Harm caused by what the business sells, serves, makes, installs or repairs.

Watch for
  • Grease duct, fume exhaust, and fire or smoke dampers in rated walls
  • Metal roofing and wall cladding on large buildings
  • Custom guards, enclosures or equipment sold to manufacturers
Controls that matter
  • Welded, tested seams and access doors on grease duct
  • Fastening and expansion details to the panel maker's specification
  • Photos and sign-off at completion of each roof detail

Workers’ injury

High
Installers work at height carrying awkward, razor-edged pieces, and shop staff use shears, brakes and rolls.

Injuries and illness to employees.

Watch for
  • Roof and gutter work from ladders without fall protection
  • Press brakes operated without light curtains or guarding
  • Work in ceilings and mechanical rooms containing old insulation
Controls that matter
  • Guardrails, anchors or lifts planned for every elevated task
  • Cut-resistant gloves and sleeves as standard issue
  • Safeguarded brakes and shears with trained operators

Commercial auto

Elevated
Vans and stake trucks leave daily carrying duct sections, long gutter stock and ladders.

Owned, hired and employee-driven vehicles, deliveries, customers’ vehicles in care.

Watch for
  • Over-length loads on roof racks or open trailers
  • Employees taking company vehicles home
Controls that matter
  • Load securing rules with flagged overhangs
  • Driving record checks, telematics and a personal-use policy

Crime and theft

Moderate
Copper sheet, coil and scrap, plus hand tools on vans, are the usual targets.

Burglary, robbery, employee dishonesty, cash, payment and invoice fraud.

Watch for
  • Copper and tools left in vehicles or on site overnight
  • Scrap sold for cash by shop staff
Controls that matter
  • Locked van storage and stock returned to the shop nightly
  • Scrap sales paid by traceable means to the company

Inland marine and equipment

Elevated
Tools, lifts and fabricated sections sit on job sites and in vehicles until installed and accepted.

Property in transit, at job sites or in the insured’s care, and mobile equipment.

Watch for
  • Prefabricated duct or panels stored on open sites
  • Rented lifts and hoists in the insured's care
Controls that matter
  • Installation floater sized to the largest job
  • Just-in-time delivery of fabricated sections to site

Environmental

Moderate
Old duct insulation, sealants and roof materials may contain asbestos, and leaks from finished work feed mold.

Pollution on or from the site or the work.

Watch for
  • Demolition of old ductwork or flashing in older buildings
  • Mold claims following duct condensation or roof leaks
Controls that matter
  • Asbestos survey before removal work begins
  • Insulation and vapor barrier details checked at handover

Cyber and data

Moderate
Ransomware on CAD, nesting and estimating systems stops the laser and coil line, though customer data is mostly business contacts.

Data breaches, ransomware, system outages and attacks on connected equipment.

Watch for
  • Laser and coil line controllers on the office network with vendor remote access
  • Emailed payment changes from suppliers and general contractors
Controls that matter
  • Offline backups of nesting programs and drawings, tested by restoring
  • Call-back check on any change to bank or payment details

Professional liability

Moderate
Shop drawings, duct layouts and design-assist work for contractors put the firm's own sizing and detailing decisions on the line.

Loss or injury caused by advice, design, testing, care or another professional service.

Watch for
  • Design-build duct systems or kitchen exhaust sized by the firm's own staff
Controls that matter
  • Engineer of record sign-off on any system the firm designs

Umbrella and excess

High
A torch fire on an occupied building, a grease duct fire years later or material dropped from a roof can exceed primary limits.

How likely one liability event is to exhaust primary limits.

Watch for
  • Hot work on occupied commercial roofs or historic buildings
  • Grease duct installed in multi-story mixed-use buildings
Controls that matter
  • Hot work permits with a fire watch after torches are put away
  • Limits matched to the largest building and contract worked on
03 / Property picture

Construction, occupancy, protection, exposure.

What a risk engineer expects to find at a typical site of this type, and what to compare a submission against.

Construction
A single-story steel or masonry shop with a yard for coil, duct sections and vans; crews work on customers' roofs, ceilings and mechanical rooms of every age.
Occupancy
Shearing, laser and plasma cutting, press braking, welding and soldering in the shop, with duct liner, sealants and small paint stocks; torch work and hoisting on job sites.
Protection
Fume extraction with spark arrestors on cutting tables, liner and adhesives kept away from hot work, extinguishers on every van, and hot work permits with fire watch on site.
Exposure
Shops sit in industrial parks beside other trades; on site, a torch on a timber roof or in a ceiling void threatens the customer's whole building and its occupants.
04 / Checklist

What to ask and look for.

Start with the desk review before quoting, then walk the site. Tick questions off as you go; ticks are kept in this browser only.

Before quoting: ask the broker or owner

Documents to request

On site: work performed

On site: job sites

On site: shop and equipment

On site: records

Refer or decline if you find

  • Open-flame work on roofs with no permit or fire watch
  • Roof and gutter work without fall protection
  • Grease duct assembled with unsealed or non-welded seams
  • Uninsured subcontract installers
  • Fire and smoke dampers installed with no inspection or test records
05 / Location

How UrbanStat data helps.

Storm seasons drive both demand and claims: half-finished roofs and flashings are exposed to wind and rain, installed metal panels to hail. Copper stock and loaded vans make local theft rates relevant.

WindHailHurricaneTornadoCrime
  • Crime scores at the address inform theft terms for copper stock, tools and loaded vans kept at the shop overnight.
  • Hail and wind scores at the address show how exposed the shop roof, yard-stored coil and duct sections, and parked vans are to storm damage.
  • The risk analysis API returns peril scores in seconds, so a small shop-and-yard location can be screened inside the quoting workflow.
Wind · Hail · Hurricane · Tornado
06 / Public loss data · NAICS 332322

What the published numbers say.

Official statistics for the industry or property type closest to this business. They describe the industry as a whole, not any one insured.

Workers’ injury frequency

3.3 recordable injuries and illnesses per 100 full-time workers, above the private-industry average of 2.3.

Sheet metal work manufacturing
3.3
All private industry
2.3

1.2 of these cases per 100 workers involved days away from work.

United States, 2024. Industry: Sheet metal work manufacturing (NAICS 332322). Source: U.S. Bureau of Labor Statistics, Survey of Occupational Injuries and Illnesses, Table 1: incidence rates of nonfatal occupational injuries and illnesses by industry and case types, 2024.

Workplace deaths

5 fatal work injuries in 2024.

Manufacturing
2.4
All workers
3.3

Deaths per 100,000 full-time equivalent workers, for the industry sector as a whole.

United States, private industry, 2024. Industry: Sheet Metal Work Manufacturing (NAICS 332322). Source: U.S. Bureau of Labor Statistics, Census of Fatal Occupational Injuries; sector rates.

Most cited safety standards

679 citations from 193 inspections; 65% were classed serious, willful or repeat.

  • 1910.212 General requirements for all machines
    61
  • 1910.147 The control of hazardous energy (lockout/tagout)
    59
  • 1910.1200 Hazard communication
    55
  • 1910.134 Respiratory protection
    43
  • 1910.217 Mechanical power presses
    24

Standards cited most often in this industry, by number of citations.

United States, citations issued October 2024 to September 2025 (federal fiscal year 2025). Industry: Sheet Metal Work Manufacturing (NAICS 332322). Covers federal and state-plan inspections. A citation is one violation item; one inspection can produce several. Source: U.S. Department of Labor, Occupational Safety and Health Administration, OSHA enforcement data (inspections and violations); standard titles from the Code of Federal Regulations, Title 29 (section headings).

Fire frequency

7,966 fires a year reported in industrial and manufacturing properties, causing about $810 million in direct property damage a year.

United States, 2020 to 2024, annual average. The group includes utility, defense, agriculture and mining properties. Source: National Fire Protection Association, Structure Fires in Industrial and Manufacturing Properties.

Toxic chemical releases

99 facilities reported toxic chemical releases totaling 359,813 pounds on and off site.

  • Certain glycol ethers
    143,411
  • Toluene
    66,028
  • Chlorodifluoromethane
    47,066

Chemicals released in the largest amounts, in pounds. 58 of the facilities reported at least one chemical classed as a carcinogen.

United States, 2024. Industry: Sheet Metal Work Manufacturing (NAICS 332322). Covers facilities in listed industries with ten or more full-time employees that handle listed chemicals above set thresholds. Source: U.S. Environmental Protection Agency, Toxics Release Inventory basic data files.

Industry loss ratios by line2020 to 2024, the same table on every guide

Loss ratios are published by line of insurance, not by business type. They show how each line has run for insurers as a whole, whatever the business insured.

Published lineClosest line in this guide20202021202220232024
FireProperty63.2%67.3%62.4%45.5%40.9%
Commercial multiple perilProperty and liability sold as a package61.2%60.2%59.4%61.2%54.4%
Inland marineInland marine and equipment64.5%49.4%47.1%44.1%44.0%
Other liabilityPremises liability, and most umbrella, professional (other than medical) and cyber cover65.1%58.8%61.0%63.7%71.2%
Products liabilityProducts and completed work48.2%52.2%46.0%57.5%60.3%
Workers’ compensationWorkers’ injury47.9%49.2%45.0%44.3%46.0%
Commercial auto liabilityCommercial auto68.3%66.5%71.9%76.8%77.6%
Commercial auto physical damageCommercial auto50.9%56.3%64.3%65.1%57.9%

United States. Losses incurred as a percent of direct premiums earned, countrywide, before reinsurance and not including loss adjustment expense. Source: National Association of Insurance Commissioners, Report on Profitability by Line by State in 2024, ten-year summary.

Coverages to raise
Contractors pollution
Disturbing old duct insulation and mastics can release asbestos, and leaking finished work feeds mold claims.
Employment practices
Field crews, seasonal hiring and subcontract labor bring wage, classification and harassment claims.
Equipment breakdown
A failed laser source or coil line controller stops duct output until parts arrive, though some work can be sent out.

NAICS and SIC codes for sheet metal shops and contractors

SystemCodeIndustry
NAICS 2022, primary332322Sheet Metal Work Manufacturing
NAICS 2022238220Plumbing, Heating, and Air-Conditioning Contractors
NAICS 2022238160Roofing Contractors
SIC 1987, primary3444Sheet Metal Work
SIC 19871711Plumbing, Heating, and Air-Conditioning
SIC 19871761Roofing, Siding, and Sheet Metal Work
Next step

See this risk on the map.

Book a 30-minute walkthrough tailored to your portfolio and perils of interest.

Request a Demo →