HVAC and heating equipment manufacturersNAICS 333415 · SIC 3585
These manufacturers stamp, braze and assemble furnaces, boilers, heat pumps, air conditioners, fans, commercial refrigeration, industrial process ovens and the controls that run them. Most products burn gas or hold refrigerant inside occupied buildings, so one design or assembly fault can cause carbon monoxide poisoning, fires and leaks across a whole production run.
NAICS 333415 Air-Conditioning and Warm Air Heating Equipment and Commercial and Industrial Refrigeration Equipment ManufacturingSIC 3585 Air-Conditioning and Warm Air Heating Equipment and Commercial and Industrial Refrigeration EquipmentNAICS 333414 Heating Equipment (except Warm Air Furnaces) ManufacturingNAICS 333413 Industrial and Commercial Fan and Blower and Air Purification Equipment Manufacturing+5 more codes
Where losses come from.
- 01
Carbon monoxide, fires and gas leaks traced to heat exchangers, burners, valves or ignition controls
- 02
Refrigerant leaks, failed coils and condensate overflows causing water damage and costly warranty campaigns
- 03
Press, brazing and paint line injuries and fires during high-volume, seasonal production
- PropertyProperty: High, 4 of 5; sector average 3.7; all business types 2.9.
- Business interruptionBusiness interruption: High, 4 of 5; sector average 3.5; all business types 2.7.
- Premises liabilityPremises liability: Moderate, 2 of 5; sector average 1.9; all business types 2.7.
- Products and completed workProducts and completed work: High, 4 of 5; sector average 3.4; all business types 2.6.
- Workers’ injuryWorkers’ injury: Elevated, 3 of 5; sector average 3.4; all business types 3.0.
- Commercial autoCommercial auto: Moderate, 2 of 5; sector average 2.3; all business types 2.5.
- Crime and theftCrime and theft: Moderate, 2 of 5; sector average 1.9; all business types 2.2.
- Inland marine and equipmentInland marine and equipment: Moderate, 2 of 5; sector average 2.6; all business types 2.6.
- EnvironmentalEnvironmental: Elevated, 3 of 5; sector average 2.8; all business types 2.3.
- Cyber and dataCyber and data: Elevated, 3 of 5; sector average 2.7; all business types 2.7.
- Professional liabilityProfessional liability: Moderate, 2 of 5; sector average 1.5; all business types 2.0.
- Umbrella and excessUmbrella and excess: High, 4 of 5; sector average 3.6; all business types 3.6.
- Heat pumps are replacing gas furnaces as buildings electrify, shifting product risk from carbon monoxide toward electrical faults, refrigerant leaks and cold-climate performance claims.
- Mildly flammable and hydrocarbon refrigerants are replacing older blends, bringing ignition hazards into charging lines, test labs, warehouses and installed units.
- Connected thermostats and building controls run through cloud apps, so a firmware fault or outage can affect heating in many buildings at once.
Twelve lines, rated.
Each line shows its rating and the reason for it; open a line for what to watch for and the controls that matter. Ratings are UrbanStat’s own editorial view of a typical business of this type, on a five-step scale. They are a starting point for questions, not a quote, a rate or a statistical measure.
Property
HighBrazing furnaces, paint lines, foam injection and flammable refrigerant charging sit under one roof with high-piled cartoned units packed in plastic foam.
Fire, explosion, water and weather damage to buildings, contents and stock.
- Hydrocarbon or mildly flammable refrigerant charged without leak detection or ventilation
- Gas-fired test stands and burn-in rooms beside cartoned stock
- Finished units racked high in foam and cardboard before peak season
- Charging stations with gas detection, interlocked exhaust and no ignition sources
- Sprinklers designed for cartoned stock with plastics and foam
- Brazing and paint areas separated from assembly and the warehouse
Business interruption
HighFin presses, tube benders and coil lines are long-lead machines, and a loss just before the heating or cooling season costs a year's sales.
How long and how costly a shutdown is.
- Compressors, motors or control boards bought from one supplier
- One plant building every unit in a product family
- Spare dies and fin tooling stored away from the main plant
- Qualified second sources for compressors, motors and electronic controls
Premises liability
ModerateFew visitors come in, but contractor training centers fire live equipment and field technicians commission large units at customers' buildings.
Injuries to customers and the public, on site or caused by operations elsewhere.
- On-site training classes running gas-fired and refrigerant equipment
- Start-up and warranty work by own technicians at customer sites
- Training rooms with gas detection, ventilation and supervised firing
- Hot work permits and lift plans for field commissioning
Products and completed work
HighAppliances burn gas and hold refrigerant in occupied homes, so a flawed heat exchanger, valve or control design repeats across every unit shipped.
Harm caused by what the business sells, serves, makes, installs or repairs.
- Space heaters, gas fireplaces and unvented heaters sold to consumers
- Coil corrosion or leak complaints rising across one production period
- Industrial ovens whose burner controls can let fuel build up and explode
- Combustion, ignition and flame rollout testing on every model and production samples
- Serial number traceability, with warranty claims trended monthly by component
- Recall plan with registered owner and installer contact data
Workers’ injury
ElevatedPress brakes, punch presses and sharp sheet edges cause hand injuries, and lifting compressors and cabinets brings strains.
Injuries and illness to employees.
- Manual handling of heavy compressors and finished units on lines
- Brazing stations with poor fume extraction
- Temporary staff added for seasonal peaks with brief training
- Light curtains and two-hand controls on presses
- Lift assists and conveyors at heavy assembly stations
- Fume extraction at brazing and welding stations
Commercial auto
ModerateFinished units ship by carrier; the company runs field service vans, sales cars and shuttle trucks between plants.
Owned, hired and employee-driven vehicles, deliveries, customers’ vehicles in care.
- Own trucks running between plants and distribution centers
- Driving record checks and telematics on service and shuttle vehicles
Crime and theft
ModerateCopper tubing, coil scrap and compressors are attractive, and finished units resell easily through informal installer channels.
Burglary, robbery, employee dishonesty, cash, payment and invoice fraud.
- Copper and aluminum scrap sold without weight reconciliation
- Trailers of finished units left in unsecured yards
- Caged scrap with weighed, documented sales paid to the company account
- Fenced, lit yard with camera coverage and gate control
Inland marine and equipment
ModerateTruckloads of finished units travel to distributors, and stock waits in outside warehouses ahead of each season.
Property in transit, at job sites or in the insured’s care, and mobile equipment.
- Stock held at distributors or outside warehouses on consignment
- Large chillers or rooftop units shipped to sites before installation
- Transit and off-premises limits matched to peak season values
- Sale terms that state where risk passes to the buyer
Environmental
ElevatedRefrigerant escapes during charging and leak testing, and paint pretreatment, degreasing and brazing chemicals leave waste streams and old solvent footprints.
Pollution on or from the site or the work.
- Older plants with past vapor degreasing using chlorinated solvents
- Refrigerant losses not logged at charging and leak-test stations
- Refrigerant recovery at test stations with logged use
- Baseline soil and groundwater study at older sites
Cyber and data
ElevatedConnected thermostats and building controls link the maker to customers' systems, and networked production lines stop when ransomware hits.
Data breaches, ransomware, system outages and attacks on connected equipment.
- Cloud apps that let users or contractors control equipment remotely
- Production and engineering networks connected to office systems
- Signed firmware updates and a process for handling reported flaws
- Segmented plant networks with offline backups of production data
Professional liability
ModerateSelection software, load calculations and application advice given to contractors can lead to undersized or misapplied systems.
Loss or injury caused by advice, design, testing, care or another professional service.
- Custom air handlers or systems designed to a project specification
- Engineering review and written terms on application advice
Umbrella and excess
HighA carbon monoxide defect or heater fire repeated across many homes brings deaths and class actions that exhaust primary limits.
How likely one liability event is to exhaust primary limits.
- Gas-fired consumer products sold in high volumes
- Past recalls or regulator inquiries on heating products
- Boiler and furnace lines old enough to draw asbestos insulation claims
- Independent safety certification and design review for every fuel-burning model
- Distributor and private-label contracts that allocate liability clearly
Construction, occupancy, protection, exposure.
What a risk engineer expects to find at a typical site of this type, and what to compare a submission against.
- Construction
- Large single-story steel-frame plants with metal or built-up roofs, often with warehouse wings added over time and high racked storage under the same roof.
- Occupancy
- Stamping, brazing furnaces, paint lines, foam injection for insulated cabinets and panels, sometimes with flammable pentane blowing agent, refrigerant charging and gas-fired test stands, with cartoned finished units stored in bulk.
- Protection
- Sprinklers designed for cartoned plastics and foam, gas detection at refrigerant and fuel test areas, automatic fuel shut-off on test stands, and monitored alarms.
- Exposure
- Yards hold finished condensing units, pallets and copper scrap against the walls, plus refrigerant cylinder cages and bulk tanks of blowing agent or brazing gas.
What to ask and look for.
Start with the desk review before quoting, then walk the site. Tick questions off as you go; ticks are kept in this browser only.
Before quoting: ask the broker or owner
Documents to request
On site: products and design
On site: plant and protection
On site: people and equipment
On site: records and history
Refer or decline if you find
- Fuel-burning products sold without independent safety certification
- Flammable refrigerant charged with no gas detection or interlocked ventilation
- Rising carbon monoxide or heater fire complaints with no root cause review
- No serial or lot traceability for heat exchangers and gas valves
- Cartoned stock racked above the sprinkler design height
How UrbanStat data helps.
Wide-span plant and warehouse roofs are exposed to tornado and wind, and condensing units stored outdoors dent in hail. Flood ruins electrical controls and the stock built up ahead of each season.
- Tornado and hail scores at the address show how exposed wide-span roofs and yard-stored condensing units are before peak-season stock builds up.
- Street-by-street portfolio views show how much insured value builds up around a plant and its nearby warehouses, with alerts when a set threshold is passed.
- Parcel and permit data give construction dates and permit history, a quick check on warehouse additions and on when charging or paint lines went in.
What the published numbers say.
Official statistics for the industry or property type closest to this business. They describe the industry as a whole, not any one insured.
2.1 recordable injuries and illnesses per 100 full-time workers, close to the private-industry average of 2.3.
0.6 of these cases per 100 workers involved days away from work.
United States, 2024. Industry: Air-conditioning and warm air heating equipment and commercial and industrial refrigeration equipment manufacturing (NAICS 333415). Source: U.S. Bureau of Labor Statistics, Survey of Occupational Injuries and Illnesses, Table 1: incidence rates of nonfatal occupational injuries and illnesses by industry and case types, 2024.
3 fatal work injuries in 2024.
Deaths per 100,000 full-time equivalent workers, for the industry sector as a whole.
United States, private industry, 2024. Industry: Ventilation, Heating, Air-Conditioning, and Commercial Refrigeration Equipment Manufacturing (NAICS 33341), the closest published group. Source: U.S. Bureau of Labor Statistics, Census of Fatal Occupational Injuries; sector rates.
150 citations from 49 inspections; 49% were classed serious, willful or repeat.
- 1910.147 The control of hazardous energy (lockout/tagout)16
- 1910.212 General requirements for all machines11
- 1910.1200 Hazard communication9
- 1910.303 General (electrical)6
- 1910.305 Wiring methods, components, and equipment for general use6
Standards cited most often in this industry, by number of citations.
United States, citations issued October 2024 to September 2025 (federal fiscal year 2025). Industry: Air-Conditioning and Warm Air Heating Equipment and Commercial and Industrial Refrigeration Equipment Manufacturing (NAICS 333415). Covers federal and state-plan inspections. A citation is one violation item; one inspection can produce several. Source: U.S. Department of Labor, Occupational Safety and Health Administration, OSHA enforcement data (inspections and violations); standard titles from the Code of Federal Regulations, Title 29 (section headings).
7,966 fires a year reported in industrial and manufacturing properties, causing about $810 million in direct property damage a year.
United States, 2020 to 2024, annual average. The group includes utility, defense, agriculture and mining properties. Source: National Fire Protection Association, Structure Fires in Industrial and Manufacturing Properties.
148 facilities reported toxic chemical releases totaling 143,732 pounds on and off site.
- Styrene48,700
- Nickel22,451
- Copper16,337
Chemicals released in the largest amounts, in pounds. 88 of the facilities reported at least one chemical classed as a carcinogen.
United States, 2024. Industry: Air-Conditioning and Warm Air Heating Equipment and Commercial and Industrial Refrigeration Equipment Manufacturing (NAICS 333415). Covers facilities in listed industries with ten or more full-time employees that handle listed chemicals above set thresholds. Source: U.S. Environmental Protection Agency, Toxics Release Inventory basic data files.
Industry loss ratios by line2020 to 2024, the same table on every guide
Loss ratios are published by line of insurance, not by business type. They show how each line has run for insurers as a whole, whatever the business insured.
| Published line | Closest line in this guide | 2020 | 2021 | 2022 | 2023 | 2024 |
|---|---|---|---|---|---|---|
| Fire | Property | 63.2% | 67.3% | 62.4% | 45.5% | 40.9% |
| Commercial multiple peril | Property and liability sold as a package | 61.2% | 60.2% | 59.4% | 61.2% | 54.4% |
| Inland marine | Inland marine and equipment | 64.5% | 49.4% | 47.1% | 44.1% | 44.0% |
| Other liability | Premises liability, and most umbrella, professional (other than medical) and cyber cover | 65.1% | 58.8% | 61.0% | 63.7% | 71.2% |
| Products liability | Products and completed work | 48.2% | 52.2% | 46.0% | 57.5% | 60.3% |
| Workers’ compensation | Workers’ injury | 47.9% | 49.2% | 45.0% | 44.3% | 46.0% |
| Commercial auto liability | Commercial auto | 68.3% | 66.5% | 71.9% | 76.8% | 77.6% |
| Commercial auto physical damage | Commercial auto | 50.9% | 56.3% | 64.3% | 65.1% | 57.9% |
United States. Losses incurred as a percent of direct premiums earned, countrywide, before reinsurance and not including loss adjustment expense. Source: National Association of Insurance Commissioners, Report on Profitability by Line by State in 2024, ten-year summary.
- Product recall
- Gas valve, ignition control or heater defects force campaigns across years of installed units and distributor stock.
- Equipment breakdown
- Presses, coil lines, brazing furnaces and test chambers fail mechanically and stop seasonal production.
- Contingent business interruption
- Compressors, motors and control boards come from few suppliers, and their outage halts final assembly.
- Transit
- Peak-season truckloads of finished units are valuable, bulky and easily damaged in handling.
NAICS and SIC codes for hvac and heating equipment manufacturers
| System | Code | Industry |
|---|---|---|
| NAICS 2022, primary | 333415 | Air-Conditioning and Warm Air Heating Equipment and Commercial and Industrial Refrigeration Equipment Manufacturing |
| NAICS 2022 | 333414 | Heating Equipment (except Warm Air Furnaces) Manufacturing |
| NAICS 2022 | 333413 | Industrial and Commercial Fan and Blower and Air Purification Equipment Manufacturing |
| NAICS 2022 | 334512 | Automatic Environmental Control Manufacturing for Residential, Commercial, and Appliance Use |
| NAICS 2022 | 333994 | Industrial Process Furnace and Oven Manufacturing |
| SIC 1987, primary | 3585 | Air-Conditioning and Warm Air Heating Equipment and Commercial and Industrial Refrigeration Equipment |
| SIC 1987 | 3433 | Heating Equipment, Except Electric and Warm Air Furnaces |
| SIC 1987 | 3564 | Industrial and Commercial Fans and Blowers and Air Purification Equipment |
| SIC 1987 | 3822 | Automatic Controls for Regulating Residential and Commercial Environments and Appliances |
See this risk on the map.
Book a 30-minute walkthrough tailored to your portfolio and perils of interest.