Flat glass manufacturers and fabricatorsNAICS 327211 · SIC 3211
Flat glass makers melt sand, soda ash and limestone in a furnace that runs without pause for years and float the ribbon over molten tin. Fabricators cut, temper, laminate and seal bought-in sheet. Molten glass, continuous firing and heavy, sharp product drive the losses.
NAICS 327211 Flat Glass ManufacturingSIC 3211 Flat GlassNAICS 327215 Glass Product Manufacturing Made of Purchased Glass+1 more code
Where losses come from.
- 01
Furnace leaks, power failures and fuel explosions that freeze or drain the melting tank
- 02
Deep cuts, crush injuries and burns from handling large hot or broken sheets
- 03
Tempered, laminated or insulating glass that breaks or fails after installation
- PropertyProperty: High, 4 of 5; sector average 3.7; all business types 2.9.
- Business interruptionBusiness interruption: Severe, 5 of 5; sector average 3.5; all business types 2.7.
- Premises liabilityPremises liability: Low, 1 of 5; sector average 1.9; all business types 2.7.
- Products and completed workProducts and completed work: Elevated, 3 of 5; sector average 3.4; all business types 2.6.
- Workers’ injuryWorkers’ injury: High, 4 of 5; sector average 3.4; all business types 3.0.
- Commercial autoCommercial auto: Elevated, 3 of 5; sector average 2.3; all business types 2.5.
- Crime and theftCrime and theft: Low, 1 of 5; sector average 1.9; all business types 2.2.
- Inland marine and equipmentInland marine and equipment: Elevated, 3 of 5; sector average 2.6; all business types 2.6.
- EnvironmentalEnvironmental: Elevated, 3 of 5; sector average 2.8; all business types 2.3.
- Cyber and dataCyber and data: Elevated, 3 of 5; sector average 2.7; all business types 2.7.
- Professional liabilityProfessional liability: Moderate, 2 of 5; sector average 1.5; all business types 2.0.
- Umbrella and excessUmbrella and excess: Elevated, 3 of 5; sector average 3.6; all business types 3.6.
- Solar panel glass and larger, heavier insulating units for energy-efficient buildings raise the value per load and the handling hazard in the plant.
- Furnaces are shifting toward electric boosting, oxy-fuel and hydrogen firing, which changes combustion risks and makes power supply even more critical.
- More recycled cullet in the batch saves energy but brings contamination that can cause inclusions, rejects and spontaneous breakage in tempered glass.
Twelve lines, rated.
Each line shows its rating and the reason for it; open a line for what to watch for and the controls that matter. Ratings are UrbanStat’s own editorial view of a typical business of this type, on a five-step scale. They are a starting point for questions, not a quote, a rate or a statistical measure.
Property
HighA tank of molten glass is held at extreme heat for years; a refractory breach spills it into the basement, cables and structure.
Fire, explosion, water and weather damage to buildings, contents and stock.
- Furnace late in its campaign with thinning sidewall refractory
- Hydrogen and nitrogen atmosphere over the tin bath
- Wooden crates, interleaving paper and plastic interlayer stored in the warehouse
- Refractory thickness monitoring with cooling and emergency patching kept ready
- Combustion safeguards and tested emergency power for cooling and controls
- Sprinklers over crate, packaging and interlayer storage
Business interruption
SevereA float line cannot be paused; a glass leak or long power loss forces a cold repair lasting months, with few alternative suppliers.
How long and how costly a shutdown is.
- One furnace feeding all downstream coating and fabricating lines
- Contracts to supply vehicle or solar panel makers on tight schedules
- No second independent power feed
- Backup generators and fuel sized to keep the furnace hot
- Planned cold repairs scheduled before refractory reaches its limit
- Supply agreements with other plants for base glass
Premises liability
LowPlants are closed to the public; outside exposure is limited to contractors and drivers collecting loads.
Injuries to customers and the public, on site or caused by operations elsewhere.
- Contractors working during furnace repairs with weak site induction
- Contractor induction and permits for work near hot or overhead hazards
Products and completed work
ElevatedSafety glazing is relied on in buildings and vehicles; spontaneous breakage, delamination and seal failure lead to injury and costly replacement programs.
Harm caused by what the business sells, serves, makes, installs or repairs.
- Tempered glass supplied for overhead, balustrade or facade use without heat soaking
- Vehicle or rail glazing with recall exposure
- Long warranties on insulating units and coatings
- Heat-soak testing and fragmentation tests logged per batch
- Permanent marking that traces each pane to a production run
- Contract terms that cap replacement and access costs
Workers’ injury
HighLarge sheets break without warning, and staff work around furnaces, tempering ovens, cutting tables and overhead handling gear.
Injuries and illness to employees.
- Manual handling of large panes off racks and trucks
- Batch house dust from sand and other raw materials
- Hot repairs made on a running furnace
- Vacuum lifters, cranes and secured A-frames in place of manual carrying
- Cut-resistant sleeves, aprons and gloves worn throughout the plant
- Heat stress and hot work procedures for furnace crews
Commercial auto
ElevatedFabricators run their own rack trucks to glaziers and building sites, where a shifted load is lethal.
Owned, hired and employee-driven vehicles, deliveries, customers’ vehicles in care.
- Glass carried on open exterior racks through city traffic
- Drivers unloading alone at job sites
- Purpose-built racks with load restraint checked before every trip
- Driver training on unloading sequence and rack stability
Crime and theft
LowSheet glass has no resale appeal; theft is confined to metals, tools and coating materials.
Burglary, robbery, employee dishonesty, cash, payment and invoice fraud.
- Precious-metal coating targets and tin stock left unsecured
- Locked storage and stock records for coating metals
Inland marine and equipment
ElevatedGlass is costly to move and easy to break, and fabricated units for a single project put high value on one truck.
Property in transit, at job sites or in the insured’s care, and mobile equipment.
- Oversize or coated panes shipped long distances or exported
- Customer-supplied glass taken in for tempering or laminating
- Engineered crates and stillages matched to the route
- Transit cover with limits matched to the largest single load
Environmental
ElevatedFurnaces emit combustion gases and dust, batch materials are stored in bulk, and mirror or coating lines use metal salts and solvents.
Pollution on or from the site or the work.
- Mirror silvering or painting lines with untreated rinse water
- Bulk fuel oil held as standby furnace fuel
- Stack abatement and monitoring kept within permit
- Diked fuel and chemical storage with treated process water
Cyber and data
ElevatedFurnace, tin bath and lehr run on networked process controls, and cutting lines depend on optimization software and order data.
Data breaches, ransomware, system outages and attacks on connected equipment.
- Outside engineers with remote access to furnace and tin bath controls
- Cutting optimization and order systems with no manual fallback
- Process control networks separated from office systems, with tested offline backups
- Manual furnace operating procedures drilled for loss of controls
Professional liability
ModerateFabricators advise on glass type, thickness and heat soaking for facades and balustrades; a wrong specification leads to breakage or falls.
Loss or injury caused by advice, design, testing, care or another professional service.
- Glass specification or structural calculations supplied for facade or balustrade projects
- Structural work checked by a licensed engineer, and terms limiting design liability
Umbrella and excess
ElevatedSafety glazing that shatters overhead or a balustrade that gives way can kill, and a shifted rack load endangers traffic.
How likely one liability event is to exhaust primary limits.
- Tempered glass for overhead, balustrade or high-rise facade use
- Vehicle glazing supplied to vehicle makers
- Heat-soak records and traceability that confine a defect to known runs
Construction, occupancy, protection, exposure.
What a risk engineer expects to find at a typical site of this type, and what to compare a submission against.
- Construction
- Float plants are huge noncombustible buildings with a furnace hall, tin bath and long lehr over basements of cables and cooling lines; fabricators use large steel-frame sheds.
- Occupancy
- Molten glass held continuously, a hydrogen and nitrogen atmosphere over molten tin, tempering ovens, and stores of wooden crates, interleaving paper, plastic interlayer and sealants.
- Protection
- Refractory monitoring, glass leak catch pits, emergency power for furnace cooling, combustion safeguards, gas detection at the tin bath, and sprinklers over crate and interlayer storage.
- Exposure
- Plants sit in industrial zones near suppliers and fabricators; outdoor crate yards and neighbors' storage add fire exposure, and a wide power outage threatens the furnace.
What to ask and look for.
Start with the desk review before quoting, then walk the site. Tick questions off as you go; ticks are kept in this browser only.
Before quoting: ask the broker or owner
Documents to request
On site: operations
On site: furnace and utilities
On site: storage and handling
On site: quality and records
Refer or decline if you find
- Furnace run past its planned campaign with no repair date
- No emergency power able to hold furnace temperature
- Tempered glass for overhead use shipped without heat soaking
- Large panes handled by hand without lifters or cut protection
How UrbanStat data helps.
A furnace full of molten glass tolerates neither shaking nor a long power outage. Flood water meeting a hot tank is destructive. Wide roofs and outdoor crate yards are open to wind and hail.
- Earthquake and flood scores at the address show how exposed a continuously fired furnace is to the two perils most likely to force an unplanned cold repair.
- Live event overlays show which glass plants lie in a hurricane's path, where a long power outage threatens the furnace itself.
- Street-by-street exposure views show how much insured value sits around the plant, since a furnace site and its fabricating customers often cluster in one industrial area.
What the published numbers say.
Official statistics for the industry or property type closest to this business. They describe the industry as a whole, not any one insured.
4.5 recordable injuries and illnesses per 100 full-time workers, above the private-industry average of 2.3.
1.5 of these cases per 100 workers involved days away from work.
United States, 2024. Industry: Flat glass manufacturing (NAICS 327211). Source: U.S. Bureau of Labor Statistics, Survey of Occupational Injuries and Illnesses, Table 1: incidence rates of nonfatal occupational injuries and illnesses by industry and case types, 2024.
28 fatal work injuries in 2024, most often from transportation incidents (11).
Deaths per 100,000 full-time equivalent workers, for the industry sector as a whole.
United States, private industry, 2024. Industry: Nonmetallic Mineral Product Manufacturing (NAICS 327), the closest published group. Source: U.S. Bureau of Labor Statistics, Census of Fatal Occupational Injuries; sector rates.
29 citations from 8 inspections; 62% were classed serious, willful or repeat.
- 1910.1200 Hazard communication4
- 1910.303 General (electrical)3
- 1910.305 Wiring methods, components, and equipment for general use3
- 1910.215 Abrasive wheel machinery2
- 1910.184 Slings1
Standards cited most often in this industry, by number of citations.
United States, citations issued October 2024 to September 2025 (federal fiscal year 2025). Industry: Flat Glass Manufacturing (NAICS 327211). Covers federal and state-plan inspections. A citation is one violation item; one inspection can produce several. Source: U.S. Department of Labor, Occupational Safety and Health Administration, OSHA enforcement data (inspections and violations); standard titles from the Code of Federal Regulations, Title 29 (section headings).
7,966 fires a year reported in industrial and manufacturing properties, causing about $810 million in direct property damage a year.
United States, 2020 to 2024, annual average. The group includes utility, defense, agriculture and mining properties. Source: National Fire Protection Association, Structure Fires in Industrial and Manufacturing Properties.
28 facilities reported toxic chemical releases totaling 1.1 million pounds on and off site.
- Lithium carbonate635,890
- Hydrochloric acid129,253
- Sulfuric acid108,091
Chemicals released in the largest amounts, in pounds. 8 of the facilities reported at least one chemical classed as a carcinogen.
United States, 2024. Industry: Flat Glass Manufacturing (NAICS 327211). Covers facilities in listed industries with ten or more full-time employees that handle listed chemicals above set thresholds. Source: U.S. Environmental Protection Agency, Toxics Release Inventory basic data files.
Industry loss ratios by line2020 to 2024, the same table on every guide
Loss ratios are published by line of insurance, not by business type. They show how each line has run for insurers as a whole, whatever the business insured.
| Published line | Closest line in this guide | 2020 | 2021 | 2022 | 2023 | 2024 |
|---|---|---|---|---|---|---|
| Fire | Property | 63.2% | 67.3% | 62.4% | 45.5% | 40.9% |
| Commercial multiple peril | Property and liability sold as a package | 61.2% | 60.2% | 59.4% | 61.2% | 54.4% |
| Inland marine | Inland marine and equipment | 64.5% | 49.4% | 47.1% | 44.1% | 44.0% |
| Other liability | Premises liability, and most umbrella, professional (other than medical) and cyber cover | 65.1% | 58.8% | 61.0% | 63.7% | 71.2% |
| Products liability | Products and completed work | 48.2% | 52.2% | 46.0% | 57.5% | 60.3% |
| Workers’ compensation | Workers’ injury | 47.9% | 49.2% | 45.0% | 44.3% | 46.0% |
| Commercial auto liability | Commercial auto | 68.3% | 66.5% | 71.9% | 76.8% | 77.6% |
| Commercial auto physical damage | Commercial auto | 50.9% | 56.3% | 64.3% | 65.1% | 57.9% |
United States. Losses incurred as a percent of direct premiums earned, countrywide, before reinsurance and not including loss adjustment expense. Source: National Association of Insurance Commissioners, Report on Profitability by Line by State in 2024, ten-year summary.
- Equipment breakdown
- Furnace fans, tin bath controls, tempering ovens, laminating autoclaves and transformers fail without fire and stop production.
- Utility service interruption
- A long loss of gas or power freezes the glass in the tank and forces a cold repair.
- Contingent business interruption
- Soda ash, tin and coated base glass come from few suppliers, and a few customers take most output.
- Product recall and replacement
- Faulty safety glazing in vehicles or buildings means tracing, removing and replacing installed panes at high cost.
See this risk on the map.
Book a 30-minute walkthrough tailored to your portfolio and perils of interest.