Adhesive and sealant manufacturersNAICS 325520 · SIC 2891

Adhesive manufacturers blend polymers, resins, tackifiers, fillers and solvents or water into glues, sealants, hot melts and reactive systems for construction, packaging, flooring, vehicles and consumers. Solvent and hot-oil processes drive fire losses, and a bond that lets go in service can mean ripping out a whole installation.

NAICS 325520 Adhesive ManufacturingSIC 2891 Adhesives and Sealants

Manufacturing · Updated November 2026

01 / Loss drivers

Where losses come from.

  1. 01

    Bond failures in flooring, roofing, glazing and assembly that require costly tear-out and replacement

  2. 02

    Fires in solvent churns, hot-melt kettles and thermal oil heating systems

  3. 03

    Solvent and isocyanate exposure to workers, and solvent releases to ground and air

How it comparesEach line’s rating against the average for its NAICS sector, Manufacturing (178 business types), and for all 747.
  1. PropertyProperty: High, 4 of 5; sector average 3.7; all business types 2.9.
  2. Business interruptionBusiness interruption: Elevated, 3 of 5; sector average 3.5; all business types 2.7.
  3. Premises liabilityPremises liability: Moderate, 2 of 5; sector average 1.9; all business types 2.7.
  4. Products and completed workProducts and completed work: High, 4 of 5; sector average 3.4; all business types 2.6.
  5. Workers’ injuryWorkers’ injury: Elevated, 3 of 5; sector average 3.4; all business types 3.0.
  6. Commercial autoCommercial auto: Moderate, 2 of 5; sector average 2.3; all business types 2.5.
  7. Crime and theftCrime and theft: Low, 1 of 5; sector average 1.9; all business types 2.2.
  8. Inland marine and equipmentInland marine and equipment: Moderate, 2 of 5; sector average 2.6; all business types 2.6.
  9. EnvironmentalEnvironmental: Elevated, 3 of 5; sector average 2.8; all business types 2.3.
  10. Cyber and dataCyber and data: Moderate, 2 of 5; sector average 2.7; all business types 2.7.
  11. Professional liabilityProfessional liability: Moderate, 2 of 5; sector average 1.5; all business types 2.0.
  12. Umbrella and excessUmbrella and excess: Elevated, 3 of 5; sector average 3.6; all business types 3.6.
What’s changing
  • Pressure to cut solvent emissions pushes the mix toward water-based, hot-melt and reactive products, lowering fire load but raising isocyanate sensitization and moisture-cure failures.
  • Adhesives now replace rivets and welds in vehicle bodies, electric vehicle battery packs and electronics, so a bond failure can turn into a safety recall.
  • Building owners ask for low-emission products and ingredient disclosures, and odor or indoor air complaints after flooring installs now lead to tear-out demands.
02 / Line by line

Twelve lines, rated.

Each line shows its rating and the reason for it; open a line for what to watch for and the controls that matter. Ratings are UrbanStat’s own editorial view of a typical business of this type, on a five-step scale. They are a starting point for questions, not a quote, a rate or a statistical measure.

Property

High
Rubber is dissolved in flammable solvent in churns, and hot melts are cooked in kettles heated by thermal oil.

Fire, explosion, water and weather damage to buildings, contents and stock.

Watch for
  • Solvent-based contact cements or rubber cements in the product mix
  • Thermal oil heaters and piping with leaks or no interlocks
  • Reactive raw materials such as isocyanates and peroxides stored warm
Controls that matter
  • Solvent mixing in a cutoff room with rated electrics and ventilation
  • High-temperature limits and low-flow interlocks on thermal oil systems
  • Bonding and grounding at every solvent transfer

Business interruption

Elevated
Mixers and kettles are replaceable within months, but customers qualify a specific formula and switch slowly back after an outage.

How long and how costly a shutdown is.

Watch for
  • Products specified into automotive or aerospace assembly lines
  • Key polymer or tackifier from one supplier
Controls that matter
  • Qualified toll blender for principal products
  • Raw material safety stock held in a separate building

Premises liability

Moderate
No public on site; the off-premises exposure is technical staff advising at customers' plants and job sites.

Injuries to customers and the public, on site or caused by operations elsewhere.

Watch for
  • Field technicians supervising application on construction sites
Controls that matter
  • Written scope for site visits and technical advice

Products and completed work

High
Adhesives are hidden inside floors, roofs, windows, vehicles and packages, so one bad batch or wrong recommendation spoils many finished installations.

Harm caused by what the business sells, serves, makes, installs or repairs.

Watch for
  • Flooring, roofing and structural glazing adhesives
  • Solvent-based consumer cements used in closed rooms near pilot lights
  • Food packaging and medical adhesives with migration limits
Controls that matter
  • Batch testing with retained samples and full lot traceability
  • Written substrate and moisture limits on every data sheet
  • Sales terms limiting liability, backed by documented technical advice

Workers’ injury

Elevated
Isocyanates and epoxies sensitize skin and lungs, solvents intoxicate, and hot melt at kettle temperature sticks to skin and burns deep.

Injuries and illness to employees.

Watch for
  • Open charging of solvents and isocyanates
  • Operators skimming or sampling hot-melt kettles by hand
Controls that matter
  • Closed charging, local exhaust and air monitoring for isocyanates
  • Heat-resistant gloves, sleeves and face shields at kettles
  • Medical surveillance for sensitizer exposure

Commercial auto

Moderate
Distribution is mostly by common carrier, with sales and technical staff driving to customers.

Owned, hired and employee-driven vehicles, deliveries, customers’ vehicles in care.

Watch for
  • Own trucks delivering flammable adhesives to job sites
Controls that matter
  • Driver checks and hazardous goods training where own trucks are used

Crime and theft

Low
Drums and pails of adhesive are not theft targets, and sales are invoiced.

Burglary, robbery, employee dishonesty, cash, payment and invoice fraud.

Watch for
  • Payment diversion fraud on supplier invoices
Controls that matter
  • Call-back verification before any change to supplier bank details

Inland marine and equipment

Moderate
Goods in transit are heat and frost sensitive, and dispensing equipment is often lent to customers.

Property in transit, at job sites or in the insured’s care, and mobile equipment.

Watch for
  • Applicators and bulk melt units placed at customers' plants
Controls that matter
  • Loan agreements and a current schedule of equipment at customers

Environmental

Elevated
Solvent storage and washings are the main pollution source; water-based and hot-melt lines add little.

Pollution on or from the site or the work.

Watch for
  • Underground solvent tanks or a history of chlorinated solvent use
  • Latex and wash water discharged without pretreatment
Controls that matter
  • Diked solvent storage with overfill protection
  • Wash water settled and reused, solids sent to licensed disposal

Cyber and data

Moderate
Formulas, batch records and order entry run on business systems; production is batch work with mostly manual controls and little personal data.

Data breaches, ransomware, system outages and attacks on connected equipment.

Watch for
  • Formulas and customer specifications held on one server with no offline copy
  • Automated dispensing and reactor controls reachable from the office network
Controls that matter
  • Offline backups of formulas, batch records and quality data
  • Separate networks for plant controls and office systems

Professional liability

Moderate
Technical staff recommend products for specific substrates and conditions, and a wrong recommendation is blamed for bond failures across a project.

Loss or injury caused by advice, design, testing, care or another professional service.

Watch for
  • Job-specific product selection or application advice given verbally
  • Field technicians approving surface preparation at job sites
Controls that matter
  • Written recommendations stating substrate, moisture and temperature limits
  • Advice logged against the job and reviewed by a second chemist

Umbrella and excess

Elevated
Most losses are costly tear-out, but a failed structural glazing bond or a solvent cement fire in a home can cause serious injury.

How likely one liability event is to exhaust primary limits.

Watch for
  • Structural glazing, facade and vehicle assembly adhesives
  • Consumer solvent cements sold through retail chains
Controls that matter
  • Sales terms that cap liability and exclude consequential losses
  • Qualification testing kept on file for each structural application
03 / Property picture

Construction, occupancy, protection, exposure.

What a risk engineer expects to find at a typical site of this type, and what to compare a submission against.

Construction
Single-story steel or masonry plants, often extended over the years, with mixing halls, kettle rooms, drum stores and finished goods sharing one roof.
Occupancy
Rubber and resins dissolved in solvent churns, hot melts cooked in thermal-oil kettles, and isocyanates and peroxides that react if stored too warm.
Protection
Sprinklers designed for flammable liquids in solvent areas, a cutoff mixing room with rated electrics, interlocked thermal oil heaters, and grounding at every transfer.
Exposure
Plants sit in industrial parks beside other manufacturers; burning solvent runs into drains and yards, and drum stores near the fence line take heat from any neighboring fire.
04 / Checklist

What to ask and look for.

Start with the desk review before quoting, then walk the site. Tick questions off as you go; ticks are kept in this browser only.

Before quoting: ask the broker or owner

Documents to request

On site: process and fire protection

On site: quality and technical service

On site: people and environment

Refer or decline if you find

  • Solvent churns in the open production area of an unsprinklered building
  • Thermal oil system with visible leaks or bypassed interlocks
  • Flooring or structural adhesive claims recurring across several jobs
  • No retained samples or batch records
05 / Location

How UrbanStat data helps.

Flood reaching solvent tanks, drum stores and bagged powders creates a spill and ruins stock. Heat-sensitive raw materials and reactive chemicals depend on power for cooling, so storm outages matter more than for most plants.

FloodHurricaneWind
  • Flood scores at the address show whether solvent tanks, drum storage and raw material warehouses at grade would be reached by water.
  • Parcel and permit data supply construction date, building value and permit history, a quick test of whether the plant was extended beyond its original fire protection.
  • Hurricane and wind scores for the site show the storm exposure of plants whose temperature-sensitive reactive stock depends on power for cooling.
Flood · Hurricane · Wind
06 / Public loss data · NAICS 325520

What the published numbers say.

Official statistics for the industry or property type closest to this business. They describe the industry as a whole, not any one insured.

Workers’ injury frequency

2.4 recordable injuries and illnesses per 100 full-time workers, close to the private-industry average of 2.3.

Paint, coating, and adhesive manufacturing
2.4
All private industry
2.3

0.7 of these cases per 100 workers involved days away from work.

United States, 2024. Industry: Paint, coating, and adhesive manufacturing (NAICS 3255), the closest published group. Source: U.S. Bureau of Labor Statistics, Survey of Occupational Injuries and Illnesses, Table 1: incidence rates of nonfatal occupational injuries and illnesses by industry and case types, 2024.

Workplace deaths

1 fatal work injury in 2024.

Manufacturing
2.4
All workers
3.3

Deaths per 100,000 full-time equivalent workers, for the industry sector as a whole.

United States, private industry, 2024. Industry: Paint, Coating, and Adhesive Manufacturing (NAICS 3255), the closest published group. Source: U.S. Bureau of Labor Statistics, Census of Fatal Occupational Injuries; sector rates.

Most cited safety standards

36 citations from 16 inspections; 64% were classed serious, willful or repeat.

  • 1910.147 The control of hazardous energy (lockout/tagout)
    8
  • 1910.178 Powered industrial trucks
    4
  • 1910.106 Flammable liquids
    3
  • 1910.22 General requirements (walking-working surfaces)
    2
  • 1910.303 General (electrical)
    2

Standards cited most often in this industry, by number of citations.

United States, citations issued October 2024 to September 2025 (federal fiscal year 2025). Industry: Adhesive Manufacturing (NAICS 325520). Covers federal and state-plan inspections. A citation is one violation item; one inspection can produce several. Source: U.S. Department of Labor, Occupational Safety and Health Administration, OSHA enforcement data (inspections and violations); standard titles from the Code of Federal Regulations, Title 29 (section headings).

Fire frequency

7,966 fires a year reported in industrial and manufacturing properties, causing about $810 million in direct property damage a year.

United States, 2020 to 2024, annual average. The group includes utility, defense, agriculture and mining properties. Source: National Fire Protection Association, Structure Fires in Industrial and Manufacturing Properties.

Toxic chemical releases

140 facilities reported toxic chemical releases totaling 1.9 million pounds on and off site.

  • Diisocyanates
    858,489
  • Toluene
    200,066
  • Dichloromethane
    193,153

Chemicals released in the largest amounts, in pounds. 62 of the facilities reported at least one chemical classed as a carcinogen.

United States, 2024. Industry: Adhesive Manufacturing (NAICS 325520). Covers facilities in listed industries with ten or more full-time employees that handle listed chemicals above set thresholds. Source: U.S. Environmental Protection Agency, Toxics Release Inventory basic data files.

Industry loss ratios by line2020 to 2024, the same table on every guide

Loss ratios are published by line of insurance, not by business type. They show how each line has run for insurers as a whole, whatever the business insured.

Published lineClosest line in this guide20202021202220232024
FireProperty63.2%67.3%62.4%45.5%40.9%
Commercial multiple perilProperty and liability sold as a package61.2%60.2%59.4%61.2%54.4%
Inland marineInland marine and equipment64.5%49.4%47.1%44.1%44.0%
Other liabilityPremises liability, and most umbrella, professional (other than medical) and cyber cover65.1%58.8%61.0%63.7%71.2%
Products liabilityProducts and completed work48.2%52.2%46.0%57.5%60.3%
Workers’ compensationWorkers’ injury47.9%49.2%45.0%44.3%46.0%
Commercial auto liabilityCommercial auto68.3%66.5%71.9%76.8%77.6%
Commercial auto physical damageCommercial auto50.9%56.3%64.3%65.1%57.9%

United States. Losses incurred as a percent of direct premiums earned, countrywide, before reinsurance and not including loss adjustment expense. Source: National Association of Insurance Commissioners, Report on Profitability by Line by State in 2024, ten-year summary.

Coverages to raise
Product recall
A bad batch built into floors, windows or vehicles must be traced and pulled from many customers at once.
Pollution legal liability
Solvent tanks, drum stores and wash water leave soil and drain contamination that general liability excludes.
Equipment breakdown
Thermal oil heaters, kettle agitators and mixers fail mechanically, stopping hot-melt and reactive lines without any fire.

NAICS and SIC codes for adhesive and sealant manufacturers

SystemCodeIndustry
NAICS 2022, primary325520Adhesive Manufacturing
SIC 1987, primary2891Adhesives and Sealants
Next step

See this risk on the map.

Book a 30-minute walkthrough tailored to your portfolio and perils of interest.

Request a Demo →