Woodworking shops
Woodworking shops saw, plane, rout, sand, glue and finish lumber and panels into cabinets, millwork, doors, store fixtures, turned goods and custom furniture, and many install the work in homes, stores and offices. Fine dust, shavings and solvent finishes feed fast fires, and saws and shapers take fingers.
Where losses come from.
- 01
Fires starting in dust collection, finishing areas or oily rags
- 02
Amputations and lacerations at table saws, shapers, jointers and routers
- 03
Installed cabinets or millwork that fall, or damage during installation
- PropertyProperty: High, 4 of 5; sector average 3.7; all business types 2.9.
- Business interruptionBusiness interruption: Elevated, 3 of 5; sector average 3.5; all business types 2.7.
- Premises liabilityPremises liability: Moderate, 2 of 5; sector average 1.9; all business types 2.7.
- Products and completed workProducts and completed work: Elevated, 3 of 5; sector average 3.4; all business types 2.6.
- Workers’ injuryWorkers’ injury: High, 4 of 5; sector average 3.4; all business types 3.0.
- Commercial autoCommercial auto: Elevated, 3 of 5; sector average 2.3; all business types 2.5.
- Crime and theftCrime and theft: Moderate, 2 of 5; sector average 1.9; all business types 2.2.
- Inland marine and equipmentInland marine and equipment: Elevated, 3 of 5; sector average 2.6; all business types 2.6.
- EnvironmentalEnvironmental: Moderate, 2 of 5; sector average 2.8; all business types 2.3.
- Cyber and dataCyber and data: Moderate, 2 of 5; sector average 2.7; all business types 2.7.
- Professional liabilityProfessional liability: Moderate, 2 of 5; sector average 1.5; all business types 2.0.
- Umbrella and excessUmbrella and excess: Elevated, 3 of 5; sector average 3.6; all business types 3.6.
- Flesh-sensing table saws and CNC nesting routers cut hand injuries at the saw, though loading and clearing CNC machines brings new pinch and crush points.
- Waterborne and UV-cured finishes are replacing solvent lacquers in many shops, reducing the flammable liquid load and the fire risk in finishing rooms.
- Imported flat-pack cabinets push local shops toward custom, high-end and commercial work, where installation, design and contract liability weigh more.
Twelve lines, rated.
Each line shows its rating and the reason for it; open a line for what to watch for and the controls that matter. Ratings are UrbanStat’s own editorial view of a typical business of this type, on a five-step scale. They are a starting point for questions, not a quote, a rate or a statistical measure.
Property
HighDry wood, fine dust on every surface and flammable lacquers meet sparks from machines, sanders and electrical gear.
Fire, explosion, water and weather damage to buildings, contents and stock.
- Dust collector or cyclone inside the shop with no spark protection
- Spraying in the open shop instead of an enclosed booth
- Stain and oil rags left in open bins
- Sprinklers, with the dust collector outdoors and ducts kept clean
- Enclosed, ventilated spray booth with filters changed regularly
- Self-closing metal cans for rags, emptied daily
Business interruption
ElevatedSmall shops rarely recover quickly: jobs in progress burn, custom orders are delayed and builders move to another shop.
How long and how costly a shutdown is.
- CNC router or edge bander with no backup
- Work for one or two builders making up most sales
- Arrangement to rent time at another shop
- Design files and cut lists backed up off site
Premises liability
ModerateCustomers visit the shop to choose finishes, and crews work inside occupied homes and buildings during installation.
Injuries to customers and the public, on site or caused by operations elsewhere.
- Customers walking through the machine area
- Installation in occupied premises with dust, tools and trip hazards
- Separate showroom or office for customer meetings
- Work areas screened and cleaned daily on site
Products and completed work
ElevatedWall cabinets, shelving and built-ins pull loose when badly fixed, and custom furniture tips or collapses.
Harm caused by what the business sells, serves, makes, installs or repairs.
- Wall-hung units installed into unknown substrates
- Stairs, railings or children's furniture in the work mix
- Fixing methods specified for each wall type and load
- Anti-tip hardware supplied with tall freestanding pieces
Workers’ injury
HighSaw blades, cutter heads and kickback cause permanent hand injuries, with wood dust, noise and lifting of sheet goods every day.
Injuries and illness to employees.
- Guards and riving knives removed from table saws
- No push sticks, feeders or flesh-sensing saws
- Inexperienced helpers on shapers and jointers
- Guarding kept in place and checked, with power feeders on shapers
- Dust extraction at each machine and hearing protection worn
- Sheet lifts or carts for panel handling
Commercial auto
ElevatedVans and box trucks, often with trailers, deliver finished work and carry installation crews most days.
Owned, hired and employee-driven vehicles, deliveries, customers’ vehicles in care.
- Unsecured cabinets and sheet goods in open trailers
- Any employee allowed to drive the truck
- Named, checked drivers and loads strapped and blanketed
- Routine vehicle and trailer inspections
Crime and theft
ModeratePortable power tools and hardware attract break-ins at the shop and theft from vans and job sites.
Burglary, robbery, employee dishonesty, cash, payment and invoice fraud.
- Tools left overnight in vehicles or unfinished houses
- Monitored alarm at the shop and locked tool storage in vans
Inland marine and equipment
ElevatedFinished cabinets, tops and millwork travel to sites and wait there for installation, along with the crew's tools.
Property in transit, at job sites or in the insured’s care, and mobile equipment.
- Completed work stored at job sites before fitting
- Stone or solid-surface tops moved by the insured
- Installation floater covering goods in transit and at site
- Delivery timed to installation dates
Environmental
ModerateLacquers, stains, thinners and adhesives are used by the drum at most; dust and noise affect neighbors.
Pollution on or from the site or the work.
- Waste finish and thinner poured out or evaporated on site
- Wood waste burned in an unapproved stove or outdoors
- Waterborne finishes where suitable and licensed solvent disposal
- Wood waste removed by a contractor or recycler
Cyber and data
ModerateCNC routers, design software and card payments rely on the network, but most shops hold few personal records.
Data breaches, ransomware, system outages and attacks on connected equipment.
- CNC programs and design files kept on one shop computer without backup
- Remote access to CNC machines left open for vendor support
- Nightly offline backup of design files and machine programs
- Vendor remote access enabled only when needed and logged
Professional liability
ModerateShops that design kitchens and prepare shop drawings for architects own the errors when dimensions, clearances or specifications are wrong.
Loss or injury caused by advice, design, testing, care or another professional service.
- Design-and-build kitchens where the shop takes measurements and layout responsibility
- Fire-rated doors or fixtures built to an architect's specification
- Signed-off drawings and field measurements before cutting starts
- Contracts limiting design responsibility to the shop's own drawings
Umbrella and excess
ElevatedA falling wall cabinet, a crash by a loaded delivery truck or a shop fire spreading to neighbors can exceed primary limits.
How likely one liability event is to exhaust primary limits.
- Fixtures and millwork installed in busy stores, schools or hospitals
- Box trucks with trailers driven by many different staff
- Engineered fixing details for heavy wall units and overhead millwork
- Named drivers with checked records and routine vehicle inspections
Construction, occupancy, protection, exposure.
What a risk engineer expects to find at a typical site of this type, and what to compare a submission against.
- Construction
- Older wood-frame or metal buildings, often on rural or edge-of-town lots or in multi-tenant industrial units, with open roof framing where dust settles on every ledge.
- Occupancy
- Sawing, routing and sanding make fine dust and shavings; lacquers, stains and contact adhesives are sprayed or wiped on; lumber, sheet goods and finished work fill the floor.
- Protection
- Sprinklers where available, a dust collector outdoors with spark detection, an enclosed spray booth, self-closing rag cans, clean electrical gear and a monitored fire and intrusion alarm.
- Exposure
- Shared walls in industrial units let fire pass to or from neighbors, and outdoor lumber racks, wood waste bins and dust collectors beside walls carry fire into the building.
What to ask and look for.
Start with the desk review before quoting, then walk the site. Tick questions off as you go; ticks are kept in this browser only.
Before quoting: ask the broker or owner
Documents to request
On site: work performed
On site: shop and fire protection
On site: machines and people
On site: vehicles and job sites
Refer or decline if you find
- Spray finishing in the open shop
- Thick dust on rafters, lights and motors
- Table saws run with guards removed
- Wood stove or waste burner heating the shop
- Unsprinklered wood-frame building shared with other tenants
How UrbanStat data helps.
Many shops occupy older wood or metal buildings on the edge of town or in rural areas, far from hydrants and fire stations. Outdoor lumber and wood waste catch embers in wildfire country, and tools draw thieves.
- Wildfire scores at the address show whether a shop with outdoor lumber, waste piles and a combustible building sits in an ember-exposed area.
- Parcel and permit data give the construction date and permit history, a check on building age, wiring upgrades and any added spray booth.
- Crime scores at the address inform alarm and tool storage requirements for a workshop full of portable equipment.
What the published numbers say.
Official statistics for the industry or property type closest to this business. They describe the industry as a whole, not any one insured.
3.5 recordable injuries and illnesses per 100 full-time workers, above the private-industry average of 2.3.
1.4 of these cases per 100 workers involved days away from work.
United States, 2024. Industry: Wood kitchen cabinet and countertop manufacturing (NAICS 33711), the closest published group. Source: U.S. Bureau of Labor Statistics, Survey of Occupational Injuries and Illnesses, Table 1: incidence rates of nonfatal occupational injuries and illnesses by industry and case types, 2024.
1 fatal work injury in 2024.
Deaths per 100,000 full-time equivalent workers, for the industry sector as a whole.
United States, private industry, 2024. Industry: Household and Institutional Furniture and Kitchen Cabinet Manufacturing (NAICS 3371), the closest published group. Source: U.S. Bureau of Labor Statistics, Census of Fatal Occupational Injuries; sector rates.
834 citations from 174 inspections; 53% were classed serious, willful or repeat.
- 1910.134 Respiratory protection116
- 1910.213 Woodworking machinery requirements72
- 1910.1200 Hazard communication59
- 1910.107 Spray finishing using flammable and combustible materials54
- 1910.147 The control of hazardous energy (lockout/tagout)52
Standards cited most often in this industry, by number of citations.
United States, citations issued October 2024 to September 2025 (federal fiscal year 2025). Industry: Wood Kitchen Cabinet and Countertop Manufacturing (NAICS 337110). Covers federal and state-plan inspections. A citation is one violation item; one inspection can produce several. Source: U.S. Department of Labor, Occupational Safety and Health Administration, OSHA enforcement data (inspections and violations); standard titles from the Code of Federal Regulations, Title 29 (section headings).
7,966 fires a year reported in industrial and manufacturing properties, causing about $810 million in direct property damage a year.
United States, 2020 to 2024, annual average. The group includes utility, defense, agriculture and mining properties. Source: National Fire Protection Association, Structure Fires in Industrial and Manufacturing Properties.
66 facilities reported toxic chemical releases totaling 2.4 million pounds on and off site.
- Xylene970,189
- N-butyl alcohol517,016
- Toluene506,748
Chemicals released in the largest amounts, in pounds. 22 of the facilities reported at least one chemical classed as a carcinogen.
United States, 2024. Industry: Wood Kitchen Cabinet and Countertop Manufacturing (NAICS 337110). Covers facilities in listed industries with ten or more full-time employees that handle listed chemicals above set thresholds. Source: U.S. Environmental Protection Agency, Toxics Release Inventory basic data files.
Industry loss ratios by line2020 to 2024, the same table on every guide
Loss ratios are published by line of insurance, not by business type. They show how each line has run for insurers as a whole, whatever the business insured.
| Published line | Closest line in this guide | 2020 | 2021 | 2022 | 2023 | 2024 |
|---|---|---|---|---|---|---|
| Fire | Property | 63.2% | 67.3% | 62.4% | 45.5% | 40.9% |
| Commercial multiple peril | Property and liability sold as a package | 61.2% | 60.2% | 59.4% | 61.2% | 54.4% |
| Inland marine | Inland marine and equipment | 64.5% | 49.4% | 47.1% | 44.1% | 44.0% |
| Other liability | Premises liability, and most umbrella, professional (other than medical) and cyber cover | 65.1% | 58.8% | 61.0% | 63.7% | 71.2% |
| Products liability | Products and completed work | 48.2% | 52.2% | 46.0% | 57.5% | 60.3% |
| Workers’ compensation | Workers’ injury | 47.9% | 49.2% | 45.0% | 44.3% | 46.0% |
| Commercial auto liability | Commercial auto | 68.3% | 66.5% | 71.9% | 76.8% | 77.6% |
| Commercial auto physical damage | Commercial auto | 50.9% | 56.3% | 64.3% | 65.1% | 57.9% |
United States. Losses incurred as a percent of direct premiums earned, countrywide, before reinsurance and not including loss adjustment expense. Source: National Association of Insurance Commissioners, Report on Profitability by Line by State in 2024, ten-year summary.
- Installation floater
- Finished cabinets and millwork wait at job sites for days, where theft, water and other trades damage them.
- Equipment breakdown
- A failed CNC router, edge bander or dust collector motor stops production without any fire.
- Contractors' tools and equipment
- Portable saws, nailers and lasers travel between van and job site daily and are easy to steal.
- Employment practices
- Small shops hire and let go often, and wage, overtime and wrongful dismissal claims follow.
| System | Code | Industry |
|---|---|---|
| NAICS 2022, primary | 337110 | Wood Kitchen Cabinet and Countertop Manufacturing |
| NAICS 2022 | 337212 | Custom Architectural Woodwork and Millwork Manufacturing |
| NAICS 2022 | 321918 | Other Millwork (including Flooring) |
| NAICS 2022 | 337122 | Nonupholstered Wood Household Furniture Manufacturing |
| NAICS 2022 | 321911 | Wood Window and Door Manufacturing |
| NAICS 2022 | 337215 | Showcase, Partition, Shelving, and Locker Manufacturing |
| NAICS 2022 | 321999 | All Other Miscellaneous Wood Product Manufacturing |
| SIC 1987, primary | 2434 | Wood Kitchen Cabinets |
| SIC 1987 | 2431 | Millwork |
| SIC 1987 | 2541 | Wood Office and Store Fixtures, Partitions, Shelving, and Lockers |
| SIC 1987 | 2511 | Wood Household Furniture, Except Upholstered |
See this risk on the map.
Book a 30-minute walkthrough tailored to your portfolio and perils of interest.